bulb AUDI A4 1999 B5 / 1.G Three Way Halogen Headlights Workshop Manual

94-3


6 -
High beam bulb
12 V, 55 W (H7)
7 -
Front fog light bulb 12 V, 55 W (H1)
8 -
Low beam bulb 12 V, 55 W (H7)
9 -
Wiring with harness connector
10 -
Trim strip Clipped onto headlight housing
11 -
Fixed bearing for reflector Only on vehicles without headlight
automatic vertical aim control
12 -
Cover Press lock down and remove toward rear
13 -
Headlight housing
14 -
Bulb socket
15 -
Turn signal bulb 12 V, 21 W, orange
16 -
Turn signal lens Removing and installing Page 94
-21
Pa
ge 3 of 16 Headli
ghts, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.EE01.94.1

94-5


1 -
Housing cover
2 -
Xenon bulb
12 V, 35 WReplacing Page 94
-12
3 -
Headlight housing
4 -
High beam bulb
12 V, 55 W (H7)Replacing Page 94
-14
5 -
Headlight beam adjusting motor -V48-/-
V49-
Removing and installing Page 94
-11
6 -
Igniter for gas discharge lamps -N195-
(Xenon)
Removing and installing Page 94
-15
Pa
ge 5 of 16 Headli
ghts, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.EE01.94.1

94-12

High intensity gas discharge (Xenon)
headlight bulbs, replacing


Replacing Xenon bulb for low beam

Removing

- Remove cover from headlight housing.

WARNING!

HIGH VOLTAGE!

Disconnect the battery Ground (GND) strap
before working on parts of the Xenon
headlight which are labeled with the yellow
high voltage symbol.

Notes:

Before disconnecting the battery, determine the
correct coding for the anti-theft radio.
After reconnecting the battery, check and
activate the vehicle's electrical equipment
(radio, clock, comfort and convenience
features, etc.) as outlined in this Repair Manual
or the Owner's Manual.
Pa
ge 12 of 16 Headli
ghts, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.EE01.94.1

94-13


Installing - Remove harness connector -1- on Xenon headlight and retaining ring -
2- by rotating counterclockwise.
- Insert new bulb into housing without touching glass with bare hands.

- Place retaining ring -1- on catches -3- of Xenon lamp -2- with two
recesses (arrows) and secure by turning clockwise.
- Reconnect harness connector and close housing cover.
Pa
ge 13 of 16 Headli
ghts, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.EE01.94.1

94-14

Replacing high beam bulbs

Removing

- Remove back portion of intake air duct on right
headlight.

- Remove cover from headlight housing.

Installing - Disconnect harness connector -1-.
- Release bulb retaining spring -2- and remove from housing.
- Insert new bulb into housing without touching glass with bare hands.
- Secure bulb with bulb retaining spring.
- Reconnect harness connector and close housing cover.
- Secure housing cover with bulb retaining spring.
Pa
ge 14 of 16 Headli
ghts, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.EE01.94.1

94-15

Ignitor for gas discharge lamps -N195-
(Xenon), removing and installing


WARNING!

HIGH VOLTAGE!

Disconnect the battery Ground (GND) strap
before working on parts of the Xenon
headlight which are labeled with the yellow
high voltage symbol.

Notes:

Before disconnecting the battery, determine the
correct coding for the anti-theft radio.
After reconnecting the battery, check and
activate the vehicle's electrical equipment
(radio, clock, comfort and convenience
features, etc.) as outlined in this Repair Manual
or the Owner's Manual.

Removing

- Remove cover from headlight housing.

- Remove harness connector -1- on Xenon bulb by rotating
counterclockwise.
Pa
ge 15 of 16 Headli
ghts, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.EE01.94.1

94-16


- Remove retainer -1- in housing cover by pressing catches (arrows).
- Guide harness connector for Xenon bulb through opening in cover.

Installing - Disconnect harness connector -1- from ignitor's harness connector.
- Remove locking plate for ignitor by loosening screws (arrows).
- Remove starter from housing.
- Install in reverse order of removal.
Pa
ge 16 of 16 Headli
ghts, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.EE01.94.1