AUDI A4 2000 B5 / 1.G Brakes Read Mesure Value Block 08 Workshop Manual

01-140


Read Measuring Value Block
(function 08)
The control module can transmit measured
values. These measured values provide
information about the operational status of the
system and the sensors connected to it. In many
cases the data supplied can be used to
troubleshoot and repair malfunctions. The
measured values from the ABS/EDL Bosch 5.3
series are contained in four display groups,
which can be accessed via their display group
numbers.

- Observe safety precautions that apply to road
tests.

- Connect the VAG1551 Scan Tool (ST) and
select address word 03 "Brake Electronics".

Notes:

When the printer is switched on, the contents of
the display will be printed out on the scan tool
log.
When reading the measuring value block, also
check wiring and connectors for loose
terminals.

Pa
ge 1 of 13 Read Measurin
g Value Block
(function 08
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.12

- Check the control module version page 01
-
128
and press the button.
Pa
ge 2 of 13 Read Measurin
g Value Block
(function 08
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.12

01-141

Rapid data transfer
HELP
Select function XX

Indicated on display:
- Press buttons -0- and -8- to select "Read measuring value block"
function 08.
Rapid data transfer
Q
08 - Read measurin
g value block

Indicated on display:
- Press -Q- button to confirm input.
Read measurin
g value block
HELP
Input display group number
XXX

Indicated on display:
- Press buttons -0-, -0- and -1-.
- Press -Q- button to confirm input.
Pa
ge 3 of 13 Read Measurin
g Value Block
(function 08
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.12

01-142
Test table: display group 1
Notes:

Display fields 1 through 4 show the current wheel circumference speeds in km/h. These are calculated by the ABS control
module -J104- on the basis of the signals received from the wheel speed sensors. If one of the display fields shows no
reading, proceed as for DTCs 00283, 00285, 00287, 00290 "ABS Wheel Speed Sensor" Diagnostic Trouble Code (DTC)
table
In order to check whether wheel speed sensors are properly allocated to each wheel, the vehicle must be raised. On
vehicles with manual transmission put the gear shift lever in neutral. On vehicles with automatic transmission move the
selector lever to position "N". Turn appropriate wheel by hand. Remaining drive wheels must be secured against turning.
When a vehicle is accelerated uniformly on a dry surface, the displayed value will increase continuously by whole
numbers; e.g. 6 km/h, 7 km/h, 8 km/h ... . The difference between displayed values 1-4 should not be more than 1 km/h
(error from out-of-round wheels). If the values jump, for instance from ...6km/h, 7 km/h, to 12 km/h...or if the difference
between the displayed values is greater than 1 km/h, then check the installation of the wheel speed sensors and rotors. Repair Manual, Brake System, Repair Group 45

Read measuring value block
1
Indicated on display
1 to 19
1)
km/h 1 to 19
1)
km/h
1 to 19
1)
km/h 1 to 19
1)
km/h


Right rear ABS wheel speed sensor

Left rear ABS wheel speed sensor

Right front ABS wheel speed sensor
Pa
ge 4 of 13 Read Measurin
g Value Block
(function 08
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.12

Left front ABS wheel speed sensor 1) On Board Diagnostic (OBD) is terminated by the ABS control module -J104- if road speed exceeds 19 km/h.
Pa
ge 5 of 13 Read Measurin
g Value Block
(function 08
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.12

01-143

Note:
The display group numbers can be selected in
sequence by pressing buttons <-1 and 3-> on the
VAG1551 scan tool, or the arrow buttons and
on the VAG1552 mobile scan tool.
- Press -C- button to input display group number
manually. Read Measurin
g Value Block
Enter displa
y group number XXX

Indicated on display:
- Press buttons -0-, -0- and -2-.
- Press -Q- button to confirm input.
Pa
ge 6 of 13 Read Measurin
g Value Block
(function 08
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.12

01-144
Test table: display group 2 Read measuring value block
2
Indicated on display
0 or 1
0 or 1

0 or 1
---


ABS solenoid valve relay:

0 not permitted during "Read measuring value block", the relay was not activated during "ignition
on".
- Electrical test, steps 1 and 2, check voltage supply page 01
-166
. If no malfunction can be found
here, replace hydraulic control unit.
1 specified value, relay was activated by ABS control module -J104- during ignition on.

Voltage at motor for ABS return flow pump:
0 specified value, there is no voltage at the motor for the ABS return flow pump.1 not permitted during "Read measuring value block", there is voltage at the motor for the ABS return flow
pump. Replace hydraulic control unit.
Brake light switch:

0 Brake pedal not operated 1 Brake pedal operated

- Check brake light switch if there are deviations. Carry out "Electrical test",
step 3 page 01
-166
.
Pa
ge 7 of 13 Read Measurin
g Value Block
(function 08
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.12

01-145

Note:
The display group numbers can be selected in
sequence by pressing buttons <-1 and 3-> on the
VAG1551 scan tool, or the arrow buttons and
on the VAG1552 mobile scan tool.
- Press -C- button to input display group number
manually. Read Measurin
g Value Block
Enter displa
y group number XXX

Indicated on display:
Note:
For display group 3 (005):
To read the display fields for engine speed and current engine torque
with the engine running, communication between the scan tool and
the control module must be terminated via the "End Output" function
page 01
-16
. Start the engine and reinitiate communication
between the scan tool and the control module.
- Press buttons -0- and -8- to select "Read measuring value block"
function 08.
- Press -Q- button to confirm input.
- Press buttons -0-, -0- and -3-.
- Press -Q- button to confirm input.
Pa
ge 8 of 13 Read Measurin
g Value Block
(function 08
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.12

01-146
Test table: display group 3 Read measuring value block
3
Indicated on display
60 to
8000
1 RPM 0 to 100
%
0 or 1
---


Traction control (ASR) button: (Only for vehicles equipped with ASR)

0 Traction control button not operated. 1 The traction control button is operated, operational condition of ASR alternates, i.e. "ASR
OFF" and "ASR ON".
- Check traction control button if there are deviations. Carry out "Electrical test", step 11 page 01
-
166
.

Actual engine torque (AET): (Only for vehicles equipped with ASR)
0% vehicle is in deceleration mode.20% - 30% represents engine idle.100% engine is offering its maximum torque.
- If no indication is displayed, proceed according to DTC 00647 "ABS-ASR engine electrical connection 2".
Diagnostic Trouble Code (DTC) table
Engine speed: (Only for vehicles equipped with ASR)

Engine speed is displayed in increments of 60 RPM, starting at 60 RPM.
- If no indication is displayed, proceed according to DTC 00529 "Wheel speed information missing. No signal". Diagnostic
Pa
ge 9 of 13 Read Measurin
g Value Block
(function 08
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.12

Trouble Code (DTC) table
Pa
ge 10 of 13 Read Measurin
g Value Block
(function 08
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.12