display AUDI A4 2000 B5 / 1.G Instrument Cluster OBD From Model Year 1999 Owner's Guide

01-34

Initiating "Adaptation" function 10 Rapid data transfer
HELP
Select function XX

Indicated on display
- Press buttons -1- and -0- to select "Adaptation" function 10.
Read Measurin
g Value Block
Q
10 - Adaptation

Indicated on display
- Press -Q- button to confirm input.
Adaptation
Q
Insert channel number XX

Indicated on display
Note:
After changing an adaptation value or after an adaptation in a specific
channel has been completed, "Adaptation" function 10 must be selected
again in order to select another adaptation channel. - Insert desired adaptation channel ( Adaptation table, Page 01
-
33
).
- Press -Q- button to confirm input.
Pa
ge 44 of 74 Instrument cluster, On Board Dia
gnostic
(OBD
) (throu
gh M.Y. 1999
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.EE01.01.1

01-35

Adaptation of fuel gauge display Rapid data transfer
HELP
Select function XX

Indicated on display
- Press buttons -1- and -0- to select "Adaptation" function 10 and press -
Q- button to confirm input.
Adaptation
Q
Insert channel number XX

Indicated on display
- Press buttons -0- and -3- to insert channel 03.
- Press -Q- button to confirm input
Pa
ge 45 of 74 Instrument cluster, On Board Dia
gnostic
(OBD
) (throu
gh M.Y. 1999
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.EE01.01.1

01-36


- Disconnect fuel level sensor harness connector (near rear seat back,
under trim in trunk), then perform adaptation of fuel level display.
- Switch ignition off.

- Using test lead, connect VAG1301 resistance tester to fuel level sensor
(see illustration).
- Set VAG1301 to value of 470.
- Wait approx. 4 minutes, switch ignition on and observe fuel gauge.
Pa
ge 46 of 74 Instrument cluster, On Board Dia
gnostic
(OBD
) (throu
gh M.Y. 1999
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.EE01.01.1

01-37

Note:

The fuel gauge reading is correct if the needle remains on the red section
at the right side of the reserve zone (see illustration).
- Press buttons -0- and -1-.
- Press -Q- button to confirm input
Channel 1 Adaptation 128
- 1 3-

The new adaptation value can be entered in two ways: step-by-step or
directly.
Note:
If a value over 255 is entered, the "adaptation" function will be cancelled
and the procedure will have to be started again. - Indicated on display
Pa
ge 47 of 74 Instrument cluster, On Board Dia
gnostic
(OBD
) (throu
gh M.Y. 1999
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.EE01.01.1

01-38
Step-by-step method:

- Press button -1- to adjust value downward,
down to 0 or press button -3- to adjust value
upward, up to 255 (example: 215). Channel 1 Adaptation 215
Q
- 1 3-

- Indicated on display
- Press -Q- button to confirm input.
Channel 1 Adaptation 215
Q
Store changed value?

- Indicated on display
- Press -Q- button to confirm input
Channel 1 Adaptation 215 Changed value is stored

- Indicated on display
-
Press button to end fuel gauge adjustment.
Rapid data transfer
HELP
Insert address word XX

Indicated on display
Pa
ge 48 of 74 Instrument cluster, On Board Dia
gnostic
(OBD
) (throu
gh M.Y. 1999
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.EE01.01.1

01-39

Adapting fuel consumption display (direct
input method) Rapid data transfer
HELP
Select function XX

Indicated on display
- Press buttons -1- and -0- to select "Adaptation" function 10 and press -
Q- button to confirm input.
Adaptation
Q
Insert channel number XX

Indicated on display
Notes: - Press buttons -0- and -3- to insert channel 03.
- Press -Q- button to confirm input
The value entered must be between 85% and 115%.Input is in steps of 5%.
Channel 3 Adaptation 100
-1 3-

Indicated on display
-
Press button.
Pa
ge 49 of 74 Instrument cluster, On Board Dia
gnostic
(OBD
) (throu
gh M.Y. 1999
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.EE01.01.1

01-40

Note:
Correction of the fuel consumption display is only
carried out with the direct input method. Channel 3 Adaptation 100Input adaptation value XXXXX

Indicated on display
Example:
Desired input value: 90%
Keyboard entry: 00090 - Input desired correction value using keypad on VAG1551, fill in leading
digits with zeroes "0".
Channel 3 Adaptation 100
Q
Input adaptation value 00090

Indicated on display
- Press -Q- button to confirm input
Channel 3 Adaptation 90
Q
Store chan
ged value?

Indicated on display
- Press -Q- button to confirm input
Channel 3 Adaptation 90 Chan
ged value is stored

Indicated on display
-
Press button to end adaptation.
Pa
ge 50 of 74 Instrument cluster, On Board Dia
gnostic
(OBD
) (throu
gh M.Y. 1999
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.EE01.01.1

01-41

Rapid data transfer
HELP
Insert address word XX

Indicated on display
Note:
If an incorrect entry is made, the VAG1551 will switch to the following
display: - Press buttons -1- and -0- to select "Adaptation" function 10 and press -
Q- button to confirm input.
Function is unknown or cannot be carried out at the moment.

Indicated on display
-
Press button.- Select "Adaptation" function 10 and adaptation channel 03 again.
- Repeat adaptation of fuel consumption display and press -Q- button to
confirm input.
Pa
ge 51 of 74 Instrument cluster, On Board Dia
gnostic
(OBD
) (throu
gh M.Y. 1999
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.EE01.01.1

01-42

Adapting multi-function display language
versions

Note:
Adaptation is only carried out on vehicles
equipped with on board computer. Rapid data transfer
HELP
Select function XX

Indicated on display
- Press buttons -1- and -0- to select "Adaptation" function 10 and press -
Q- button to confirm input.
Adaptation
Q
Insert channel number XX

Indicated on display
- Press buttons -0- and -4-.
- Press -Q- button to confirm input
Channel 4 Adaptation 1
-1 3-

Indicated on display
Notes:
The display shows only the last digit of the five-digit language code,
e.g. 1 for German. Input of incorrect values will end the adaptation function. "Adaptation"
function 10 must be selected again. When using the VAG1551 keypad, only the direct input method can be
used.
Pa
ge 52 of 74 Instrument cluster, On Board Dia
gnostic
(OBD
) (throu
gh M.Y. 1999
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.EE01.01.1

01-43

Language version coding table

Code
Language
00001 German
00002 English
00003 French
00004 Italian
00005 Spanish
00006 Portuguese
Step-by-step method:

- Press button -1- to move downward and button -
3- to move upward through codes. Example: 2
for English. Channel 4 Adaptation 2
Q
-1 3-

Indicated on display
- Press -Q- button to confirm input.
Channel 4 Adaptation 2
Q
Store changed value?

Indicated on display
- Press -Q- button to confirm input.
Channel 4 Adaptation 2 Chan
ged value is stored

Indicated on display
-
Press button to end language version adaptation.
Pa
ge 53 of 74 Instrument cluster, On Board Dia
gnostic
(OBD
) (throu
gh M.Y. 1999
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.EE01.01.1