delete AUDI A4 2005 B6 / 2.G RNS_E Navigation System Manual

NAME (directory)103
General operation
RADIO, CD
NAME, TEL
NAV, INFO
CAR, SETUP
–Confirm Are you sure you want to delete this entry? w ith
Ye s. The selected directory entry is deleted.Deleting all directory entriesFig. 108 Directory: Delete directory– Press the function button
page 16 if another
menu is currently being displayed.
–Select Delete directory
fig.108.
–Confirm Are you sure you want to delete all entries from
the directory? with Ye s. All directories entries are
deleted.
Setting directory navigation destinationFig. 109 Directory: Select category
Fig. 110 Directory: Enter navigation destination for an entry
NAME

Navigation (NAV) 116
– Press the function button
page 16. The main
navigation menu
page 115, fig.120, the route plan

page 139, fig.146 or the previously active navigation
function menu appears in the display.
– Press the appro priate control button
page 17 to get to
the submenu through
page 115, fig.120.
The following submenus are available in navigation
function:
NAV
A1
A
Control button
functions 
page 115,
fig. 120
Navigation submenus

Memory
Previous destinations
To p c a t e g o r i e s
Load from directory
Store in directory
Load route
Store route
Delete route

Route
Route with stopover/
Route without stopover
Route list
Route criteria
Avoid route from here

Map
Zoom
Map side menu

Nav-Info
Location data (street or city where appli-
cable)
Latitude/longitude of current location
Receivable satellites
Data for final destination and where
applicable
all stopovers
Time of arrival
Distance
A1AA A

Navigation (NAV)117
General operation
RADIO, CD
NAME, TEL
NAV, INFO
CAR, SETUP The following submenus are available in navigation
Setup function:
Main navigation menuEntering a navigation destination
Destinations can be easily entered in various ways.Fig. 121 Navigation: Destination entry menu (main menu)First determined whether you would like to navigate to a final desti-
nation with or without stopovers
page 139. After you have
decided on the type of guidance (with/without stopovers), you can
enter a destination over different routes. Entering destination data
in the entry menu
fig.121 is handled in the same way in single
destination and route planning mode.
Navigation submenus
Press the
function button in
the NAV function page 151
Map scheme (day/night)
Orientation
Map type
Map contents
Voice information
Delete previous destinations
Turn list
Highway info
Intersection map
Auto intersection zoom
Compass
Version information
Demo mode
Set position/direction
SETUP

Navigation (NAV)119
General operation
RADIO, CD
NAME, TEL
NAV, INFO
CAR, SETUP
– Press the function button
page 16.
– Press the control button with the Route function.
–Select Route without stopover to switch to single desti-
nation mode
page 119
page 139. The destination
entry menu
page 117, fig.121 appears, or
–Select Route with stopover to switch to route plan

page 121 and then select Destin.. The destination
entry menu
page 117, fig.121 appears.
–Select Region
page 118, fig.122.
–Select another Region from the list
page 118, fig.123
by rotating and pressing the control knob.When selecting a country, destination data (street, city and catego-
ries) that was previously stored in the destination entry menu is
deleted.
Entering single destination (Route without stopover)Fig. 124 Navigation: Entering the destination using the speller–Press the function button
page 16.
– If necessary,Press the control button with the Route fu n c -
tion and confirm the Route without stopover function to
s w i t ch to si n g l e d e st i n at i o n m o de
page 139. Th e de s t i -
nation input menu
page 117, fig.121 appears.
– Select ggf. Region
page 118.
– Select City and enter the name using the speller,

fig.124 or
– In the speller display, select LIST
fig.124 and select
the city from the list.
NAV
NAV

Navigation (NAV)123
General operation
RADIO, CD
NAME, TEL
NAV, INFO
CAR, SETUP
Destination input street
Wi thi n a se le cted reg ion, a stre et c an b e select ed e ve n
without specifying a city.Fig. 126 Navigation: Entering a street as destination using the spellerFig. 127 Navigation: Set more detailed street information
– In a destination input menu
page 117, fig.121, select
another Region
page 118 from the list by rotating and
pressing the control knob or confirm the region already
being shown. This deletes all existing entries in the desti-
nation input menu
page 117, fig.121.
– Select Street
page 117, fig.121 and enter the street
name using the speller, or
– In the speller display, select LIST
fig.126 and select
the street from the list.
– Select a location from the following list.
– Select End entry
fig.127.
– Geben Sie ggf. Enter stopovers for route guidance with
stopovers
page 139.

Navigation (NAV) 124
– Select Start route guidance
page 129.I f y o u s e l e c t a re g io n
page 118, existing entries in the destination
input menu
page 117, fig.121 (city, street and special destina-
tion) are deleted. This allows you to search for a street within a
region.
If the street entered exists in different cities, these cities are listed
for you. Select one of the cities suggested.
After selecting the street, you can set more detailed destination
criteria by entering an Intersection or a Street number
page 128.Destination input cityFig. 128 Navigation: Entering the destination using the spellerFig. 129 Navigation: More information about destination
– In a destination input menu
page 117, fig.121, enter
another Region as applicable
page 118.
– Select City.
– Using the speller, enter the desired city
page 119,
fig.124 and confirm the city entry with OK, or
– In the speller display, select LIST and select the city from
the list.
– Select Select city center
fig.129 to navigate to the
center of the selected locality.
– Select Start route guidance
page 129.Instead of the city center, you can also enter the street, select a
special destination in the city or select on the map display.

Navigation (NAV) 134Memory control buttonPrevious destinations
The previous destinations are stored and can be
loaded directly as a navigation destination.Fig. 140 Navigation: select previous destinations–Press the Memory c o n t r o l b ut t o n i n t h e n a v i g a t i o n m e n u .
– Select Previous destinations. You will see a list of the
most recently entered destinations. This list is updated
automatically.
– Select your desired entry.
– Select Start route guidance.Tips


There may be entries which cannot be displayed fully in the
display because they contain too many letters and are too long. If
you select one of these entries using the control knob, a second
window will open up after a few seconds. You will be given addi-
tional information about the selected entry in this window.


The list of previous destinations can be deleted in the Setup
Navigation menu
page 156.
To p c a t e g o r i e sFig. 141 Navigation: Top categories–Press the Memory control button in the navigation menu.

Navigation (NAV)137
General operation
RADIO, CD
NAME, TEL
NAV, INFO
CAR, SETUP
Tips
Administration of the directory data is handled through the
button
page 98.
Save route
Once calculated, route plans can be saved with the
route criteria you entered and loaded later as a new
destination.Fig. 144 Navigation: Route plan– Enter a route plan
fig.144.
–Press the Memory co n t ro l bu t to n i n t h e n a vi g a t i o n m e n u .
–Select Save route.– Using the speller, enter the name for the route.
– Select OK in the speller. The route plan entered is saved.
A route plan provides the option of setting up to three stopovers in
addition to a destination
page 121. You can then drive to each of
these destinations in turn in the sequence set up.
The route entered will be saved with the final destination and stop-
overs and can be loaded again as a new destination
page 137.
The route plan can be changed at any time after input is complete.
Select a destination from the route plan by rotating and pressing
the control knob. Then you can select Change, Move, Delete o r Drive
to now
page 137.
If you have selected the Drive to now function and you would not
l i k e t o e d i t t h e r o u t e , r o u t e g u i d a n c e i s i m p o r t e d a n d c u r r e n t v e h i c l e
location is used as the route guidance starting point after you have
selected Start route guidance.
If the Save route f u n c t i o n i s g r e y e d o u t , t h i s i n d i c a t e s t h a t e i t h e r t h e
route memory is full or the Route without stopover function (single
destination mode) is set. Please delete routes not needed from the
route memory
page 138. Or select the Route with stopover func-
tion
page 139Tips
You can save individual destinations to the directory
page 135.
Load route–Press the Memory c o n t r o l b ut to n i n t h e n a v i g a t i o n m e n u .
NAME

Navigation (NAV) 138
– Select Load route
page 134, fig.140.
– Select the route that you would like to load from the list.
– Select Start route guidance.After storing several route plans
page 137, they can be loaded
with a few operating steps.
A route plan can be changed at any time. Select a destination from
the route plan by rotating and pressing the control knob. Then you
can select Change, Move, Delete or Drive to now.
Change
Here you are entering new navigation data for your destination or
stopover.
Move
Here you are reordering the sequence of your destination and stop-
overs.
Delete
The selected destination or stopover can be deleted. If you delete a
destination, the system will automatically select a stopover and
make that your new destination.
Drive to now
You can drive directly to the selected final destination or stopover.
If you do not want to ed it the saved route, the route will b e sa ved in
the memory when Start route guidance is activated and the current
vehicle location will be used as the starting point for navigation.
Tips
A function may not be selected (“greyed-out”) if it is not available
according to the restrictions you have set, or if not permitted by
local circumstances.Delete route–Press the Memory control button in the navigation menu.
– Select Delete route.
– Select the route to be deleted from the list.
–Confirm Are you sure you want to delete the route? with
Ye s. The selected route is deleted.

Navigation (NAV) 140stopover, your route guidance will proceed with stopovers until you
select and confirm Route without stopover.
Route with stopover
Select this option to be guided to your final destination with stop-
overs.
Stopovers can also be special destinations
page 126.
Stopovers already entered can be deleted, changed or moved at any
time, or you can drive to them immediately page 137.
Route without stopover
Select this option to navigate directly to your destination.
Tips
If you switch to the Navigation function and you are shown the
menu for Route planning
page 139, fig .1 4 6 , y o u a r e in r o ut e g u id -
ance with stopovers. If you would like to navigate directly to a final
destination, select and confirm Route without stopovers in the menu
for the Route function.
Route listFig. 147 Navigation: Route list–Press the Route control button in the navigation menu.
– Select Route list
page 139, fig.145 . The detai led route
list appears
fig.147.The route list provides you with the following information:

Notes on the route


Distance information


Street designations


City namesTips
If route guidance is not activated, Route list will be greyed-out.