Page 96 AUDI A4 2008 B8 / 4.G Infotainment MMI Operating Manual

Handset for the Bluetooth car telephone kit 30
Handset for the Bluetooth car telephone kit
Applies to vehicles: with handset for the car telephone kit
Introduction
Requirements for the use of the telephone
•The car telephone kit must be switched on
page 26.
•The handset must be switched on
page 140.
•A Bluetooth connection must exist between the handset and the
car telephone kit
page 27.
•A SIM card must be in the handset
page 31, or
•If a mobile phone with SIM Access Profile is connected, the SIM
card must be in the mobile phone
page 24.
•The PIN code for the SIM card must have been entered

page 31.
SIM card
If there is a SIM card in the handset and a mobile phone with SIM
card is connected, the SIM card in the handset is used.
For more information on how to insert the SIM card in the handset,
please refer to
page 31.
Twin card
A twin card is a second SIM card for one telephone number. If you
are using a twin card in the handset, you should activate the PIN
query
page 98. The SIM card in the vehicle is then only activated
when you enter the PIN.
Note
•You can still place an emergency call without a SIM card

page 147.
•The handset supports “Supplementary Services”, for example if
you want to check how much credit is still available on a prepaid
card.
•When using twin cards, calls can be disconnected suddenly if
two or more cards are in operation at the same time. Please contact
your mobile network service provider if you have any questions.
•These telephone functions depend on your mobile network
service provider. For more information, contact your service
provider.
•Some mobile telephones with Hands-Free Profile do not support
the handset. If this is the case, delete the handset from the Blue-
tooth device list
page 96 or insert the SIM card into the handset.
For further information, please ask an Audi dealer or specialist
retailer.
Applies to vehicles: with handset for the car telephone kit
Cleaning and care
Take good care of the handset.
Storing and handling
Keep the handset out of the reach of small children.
Always place the handset back into the carrier after use. Otherwise,
you could place yourself or others at risk when braking or during an
accident.
The handset is ideally protected against scratches and sunlight in
the carrier.
Keep the handset away from water etc.
Do not open the device or any other parts of the system. The device
could be damaged if it is not serviced by a professional.





 




Handset for the Bluetooth car telephone kit31
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control Do not let the handset fall and avoid shaking and knocking as much
as possible.
Care and cleaning
Use a cloth dampened with a mild detergent to clean the unit.
Do not use solvents or other harsh chemicals.
Caution
Do not expose the handset to strong sunlight.
Setting up
Applies to vehicles: with handset for the car telephone kit
Inserting and removing the SIM card
Inserting SIM card
– Open the centre armrest.
– Press the release button on the handset carrier.
– Remove the handset. The SIM card slot is at the top end
of the handset
fig. 22.
– Insert the SIM card into the card holder
fig. 22. Make
sure that the card slides all the way into the slot. The cut-
away corner of the SIM card should be at the bottom left.
The correct position of the SIM card is shown on the
handset display.
– If necessary, enter the PIN on the keypad
page 140,
fig. 124 and press the control button for OK.
Removing SIM card
– Open the centre armrest.
– Press the release button on the handset carrier.
– Remove the handset. The SIM card slot is at the top end
of the handset.
Fig. 22 Position for
SIM card when
inserting
Fig. 23 Removing SIM
card





 




Handset for the Bluetooth car telephone kit 32
– Press the SIM card holder down with the SIM card still in
it and then let go of the holder again
page 31, fig. 23.
The SIM card will be released.
– Remove the SIM card from the SIM card holder.
If the SIM card is inserted improperly, or if it is damaged or not
compatible, the message Please insert the SIM card
page 31,
fig. 22 will appear on the display. Remove the SIM card and insert it
properly or replace it with another SIM card.
The PIN (Personal Identification Number) protects your SIM card
against unauthorised use. You receive the PIN code from your
mobile network service provider together with the SIM card.
If you enter the wrong PIN code three times
4) in a row, your SIM card
will be blocked and a message will appear in the display.
The PUK (Personal Unblocking Key) is used to unblock a SIM card
which has been blocked. You receive the PUK from your mobile
network service provider together with the SIM card.
WARNING
Always keep the SIM card out of reach of young children; it is rela-
tively small and could possibly be swallowed.
Caution
•The handset and the SIM card can be damaged if care is not
taken.
−Please do not use force when sliding the SIM card into the slot.
−When inserting the SIM card, make sure it is in the correct
position.
•There are many different telephone SIM cards available on the
market, so it cannot be guaranteed that every card will function properly. The old type of SIM card (5V technology) can no longer be
used. If you have this type of SIM card, please contact your mobile
network service provider to obtain a replacement (with 3V tech-
nology). Never attempt to operate your telephone with an incompat-
ible SIM card, as this can cause damage to the card or your tele-
phone.
•The SIM card contacts can be easily damaged by scratches or
bending. For this reason, handle the SIM card with care.
Note
•When using a twin card please follow the recommendations of
your provider. Otherwise, you may experience connection problems
and callers may not be able to reach you.
•You can also enter the PIN and PUK using the MMI
page 88.
•If you are using a twin card in the handset, you should activate
the PIN query
page 98. The SIM card in the vehicle is then only
activated when you enter the PIN.
Applies to vehicles: with handset for the car telephone kit
Charging and changing the battery
Inside the handset is a rechargeable lithium ion battery.
4)The total number of times you can enter the PIN code may vary depending
on your type of SIM card
Fig. 24 Opening the
battery cover











Handset for the Bluetooth car telephone kit33
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control
Charging the battery
– Place the handset into the carrier. The battery is charged
in the handset.
Changing the battery
– Switch off the handset
page 140.
– Release the latch
page 32, fig. 24.
– Lift the cover.
– Remove the old battery
fig. 25.
– Insert the new battery with the contacts facing down
(Audi symbol facing upwards). Note the installation
instructions on the battery.
– Place the notches of the cover into the lower section of
the handset and press the cover back into place.
Charging the battery
The battery level indicator
page 142, fig. 126 shows the power
level of the battery. If all of the segments (vertical bars) are shown,
the battery is fully charged. The battery level indicator flashes while
the battery is being charged.A new battery only reaches its full capacity if it is fully charged and
discharged several times.
Changing the battery
Batteries have a limited service life. When the operating time of the
battery has considerably reduced, it is time to replace the battery.
WARNING
•Batteries can cause injuries and property damage.
−Keep battery contacts away from conducting materials such
as jewellery or keys.
−Do not heat the battery, as this can cause chemical
substances to be released. Note the symbols on the battery.
−Do not dismantle the battery. This could cause a battery
short-circuit or the release of chemical substances.
−Keep the battery away from naked flames to prevent explo-
sion.
•The handset and battery should not be exposed to extremely
hot or cold environments.
•Always keep the battery out of the reach of children.
Caution
•Prevent the battery from coming into contact with liquids.
•Do not expose the handset or battery to strong sunlight.
•Do not drop the handset or battery.
For the sake of the environment
Batteries contain toxic substances. They must be disposed of appro-
priately and must not be discarded with ordinary household waste.
Fig. 25 Changing the
battery
WARNING (continued)





 




Basic operation 40
Basic operation
All MMI menus at a glance
The menu structure
page 38, fig. 26 and
page 39, fig. 27
contains the available options for each main function of the MMI
system.
Note
Depending on the equipment fitted in your vehicle, the menus may
differ from those shown here.
Switching on and off
Vehicles without advanced key*
– The ignition must be switched on to turn on the MMI
system. The menu of the last main function selected will
appear. The last used audio/video source will automati-
cally be activated.
– To switch off the MMI system, remove the ignition key.
Your settings will be stored.Vehicles with advanced key*
– To switch on the MMI system, press the button.
– To switch off the MMI system, press the button
twice. Your settings will be stored.
Manual mode
– To switch on the MMI system, briefly press the ON/OFF
button
fig. 28.
– To switch off the MMI system, press and hold the ON/OFF
button until the MMI is switched off.
The MMI system will not be switched on automatically when the
ignition is switched on if it was turned off manually the last time it
was operated.
The MMI system remains in operative mode for approximately 10
minutes after the ignition is switched off. If you do not press any
function selector button, control button or the rotary pushbutton on
the MMI control console within this time period, the MMI system
will be switched off automatically.
Note
If the ignition is switched off and the battery charge level is low, the
MMI system will be switched off automatically.Fig. 28 ON/OFF button
START
STOP










Basic operation 42
MMI display
“Standard” menus
After pressing a function selector button
page 41, a menu will
appear in the MMI display.
Fig. 30 Setup Naviga-
tion
Fig. 31 Radio
submenu
LegendSymbol /
MarkingExplanation
Heading
Selected mode (e.g. radio
fig. 31).
Display in Setup menu: Setup menu in
the selected mode (e.g. Setup Naviga-
tion
fig. 30).
In vehicles with a telephone* the net-
work provider and, if applicable, the
roaming symbol
 will be shown.
TMC symbolsReception of TMC traffic messages

page 121.
Arrows
pointing
up/downIndicate further menu options
(next/previous page).
CursorPoints to the item selected in a menu.
Selected
optionA selected item is highlighted in white.
Selection boxSelection possibilities for selected
item.
ArrowIndicates more selection or setting
possibilities.
Temperature
display*Selected temperature setting in vehi-
cles with automatic air conditioner*.
Signal
strength indi-
cator*Quality of mobile phone connection,
or
PIN: Entering PIN
page 88
PUK: Entering PUK
page 88
SIM: Inserting SIM card
Envelope*
Unread text message
page 100.
Crossed-out envelope: No more text
messages can be received (SIM card
memory is full)
page 100.
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10











Basic operation43
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control
Speller
Use the speller to enter addresses, a navigation destina-
tion or a telephone number.
Some functions in the directory, telephone* or navigation* mode
require you to enter letters or numbers. In the MMI display the
speller for numbers
fig. 32 or letters
fig. 33 will appear.
While entering the numbers/letters, you can switch from numbers
to letters and vice versa as desired by turning the rotary pushbutton
to 0..9
fig. 33 or A..Z
fig. 32 and then pressing the rotary
pushbutton.
All symbols for entering letters and numbers are explained in the
following table:
TP symbolReception of traffic reports
page 58.
Corners of
display
Indicates the functions that can be
selected.
Use control buttons to select func-
tions. The top right corner of the dis-
play corresponds to the top right
control button.
SubtitlesInforms you of a selected option (e.g.
current radio station).
Function
wheelIs operated by turning and pressing
the rotary pushbutton.
Crossed-out
loudspeaker
symbolCurrent audio source is muted.
Time
Telephone
symbol*Missed calls*
page 91, fig. 85.
LegendSymbol /
MarkingExplanation
A11
A12
A13
A14
A15
A16
A17
Fig. 32 Speller for
numbers: Entering
phone numbers
Fig. 33 Speller for
letters: Finding a direc-
tory entry
A11A5





 




Basic operation 44
Entering letters, numbers and symbols using
the speller
You can find an overview of the speller on
page 43.
Entering letters, numbers and symbols
– Turn the rotary pushbutton and select the letter, number
or symbol with the cursor . The selected figure will
appear larger in the selection ring .
– To apply the letter, number or symbol, press the rotary
pushbutton. Your entry will appear in the entry space .
– After entering all the characters, turn the rotary push-
button to OK and press the rotary pushbutton.
Deleting letters, numbers and symbols
– Turn the rotary pushbutton and use the pointer to select
DEL .
– To delete the last character in the entry space, press the
rotary pushbutton.
– To delete all characters in the entry space, press and hold
the rotary pushbutton until no characters are displayed
in the entry space.
In some cases (such as when using the navigation* function) certain
letters are not available for selection if they are an illogical option.
This means that you can only select those letters that are offered as
a logical possibility for this entry.
Use the speller for numbers to enter special characters (such as a
dash or full stop).
LegendSymbol /
MarkingExplanation
Po i n t e rTo highlight the selected item in white
and make it appear larger in the selec-
tion ring.
DELTo delete the character to the left of
the highlighted cursor.
To move the cursor in the entry space
forwards and backwards.
OKTo confirm a completed entry.
A...ZTo switch the speller from numbers to
letters.
Cursor
Entry space
Selection ringTo enlarge the character selected with
the cursor.
To switch from lower case to upper
case letters.
LISTTo show a list of suggestions.
0..9To switch the speller from letters to
numbers.
SpaceTo enter a space in the entry space.
List of sug-
gestionsTo show suggested entries in alpha-
betical order.
Indicates additional list entries.
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A1
A8
A7
A4
A2










Basic operation 46
If you are in CD mode, the CD playback will be paused while the
mute function is activated.
Note
You can also adjust the volume by scrolling the right thumbwheel
on the multi-function steering wheel up and down without having
to remove your hands from the steering wheel
page 129.
Other audio sources
The volume of the voice guidance*, traffic reports*, the
speech dialogue system* and the telephone* can be
adjusted separately.
The system automatically sends a test message while the
settings are being adjusted.
– Starting from any of the audio, TV*, or SETUP menus,
press the control button for Sound
page 41.
– Turn the rotary pushbutton and select Volume settings.
– Press the rotary pushbutton. The Volume settings menu
will appear on the MMI display
fig. 36.
– Turn the rotary pushbutton to select an item in the menu.– Press the rotary pushbutton. Now you can adjust the
volume for the selected item.
– Turn the rotary pushbutton to select the desired volume.
– Press the rotary pushbutton to confirm your adjustment.
Note
Select Audio during route guid. to adjust the volume of the current
audio source during route guidance (spoken navigation
directions).
Adjusting the sound
Basic settings
Fig. 36 Volume
settings
Fig. 37 Selecting
balance





!




Basic operation47
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control
– Starting from any of the audio, TV*, or SETUP menus,
press the control button for Sound
page 41.
– Turn the rotary pushbutton to select an item in the menu
(e.g. Balance
page 46, fig. 37).
– Press the rotary pushbutton. The selected item will
appear larger on the MMI display
fig. 38.
– Turn the rotary pushbutton clockwise or anti-clockwise to
adjust the sound settings.
– Press the rotary pushbutton to confirm your adjustment.
The following sound settings are available:
•Balance: Varies left and right volume levels
•Fader: Varies front and rear volume levels
•Tr e b l e
•Bass
•GALA (speed-dependent volume control)
•Subwoofer* (for extra bass depth)6)
•DSP *
page 47
•DSP Bang & Olufsen*
page 48
•Volume settings for other audio sources
page 46
The settings for treble and bass are effective for the currently
selected function. The settings for balance and fader apply regard-
less of the selected function.
Applies to vehicles: with DSP
Digital Signal Processing (DSP)
With the sound focus function you can achieve three-
dimensional sound effects. GALA adjusts the volume level
and sound settings to the vehicle's speed.
Displaying the DSP menu
– Starting from any of the audio, TV*, or SETUP menus,
press the control button for Sound
page 41.
– Turn the rotary pushbutton to DSP and press to confirm.
The DSP menu will appear on the MMI display
fig. 39.
Sound focus
– Turn the rotary pushbutton to Sound focus and press to
confirm.
6)The subwoofer cannot be adjusted if your vehicle is equipped with the Bang
& Olufsen* sound system.
Fig. 38 Adjusting
balance
Fig. 39 Adjusting
three-dimensional
sound effects (sound
focus)