AUDI A5 2008 B8 / 1.G Infotainment MMI Operating Manual

Basic operation129
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control
•If your vehicle is not equipped with these systems, the corre-
sponding button has no function.
Applies to vehicles: with multi-function steering wheel
Adjusting the volume
The volume of the active audio source (radio, CD, Audi
music interface*, TV*) and the route guidance cues can
be adjusted on the multi-function steering wheel.
Important: The MMI system must be switched on

page 40.
Increasing and reducing the volume on the
active audio source
– Use the right thumbwheel
page 128, fig. 110 to
scroll up/down.
Mute
– To mute the MMI system, scroll the right thumbwheel

page 128, fig. 110 down until a crossed-out loud-
speaker symbol appears in the status line of the MMI
display. Any activated media drives will be paused. Pause
will also appear in the heading of the MMI display.
– To deactivate the mute/pause function, scroll the right
thumbwheel up. Playback of the paused media drive will
then be resumed.
Route guidance
– Press the right thumbwheel
page 128, fig. 110. The
last route guidance cue will now be repeated.
– To change the volume, scroll the right thumbwheel
up/down during the route guidance cue.
Listening to the radio
Applies to vehicles: with multi-function steering wheel
Calling up the radio menu
Important: The radio function on the MMI system must be
switched on
page 54.
– Press the button
page 128, fig. 110 repeatedly
until the radio menu appears in the display of the driver
information system
page 130, fig. 113.
Would you like to find out more about the radio function in your
vehicle? You can find a detailed description on
page 53,
“Listening to the radio”.
Applies to vehicles: with multi-function steering wheel
Setting the waveband
The four wavebands FM, MW, LW and DAB* (digital radio)
are displayed at the top of the display of the driver infor-
mation system.
Important: The radio menu must be displayed
page 130,
fig. 113.
A4
A4
A4
Fig. 112 List of wave-
bands
MODE











Basic operation 130
– Use the left thumbwheel
page 128, fig. 110 to scroll
down and select a waveband.
– Press the left thumbwheel to confirm the waveband.
Applies to vehicles: with multi-function steering wheel
Selecting a station from the station list
Important: The radio menu must be displayed
fig. 113.
– Use the left thumbwheel
page 128, fig. 110 to scroll
up/down and select a radio station.
– Press the left thumbwheel to tune to the station.
Note
Any stations that appear in grey lettering in the MMI display are not
displayed in the driver information system.
Applies to vehicles: with multi-function steering wheel
Selecting a stored station
Important: The radio menu must be displayed
fig. 113,
and a station must be stored in the memory list
page 57.– Use the left thumbwheel
page 128, fig. 110 to scroll
up/down and select Memory.
– Press the left thumbwheel. The radio memory list will be
displayed.
– Scroll the left thumbwheel to select a radio station and
press the left thumbwheel. The system will tune to the
radio station.
Playing media
Applies to vehicles: with multi-function steering wheel
Calling up the media menu
Important: The media function must be activated on the
MMI system, and an audio source must be selected

page 63.
– Press the button
page 128, fig. 110 repeatedly
until a list of tracks
fig. 114 /
page 131, fig. 115
appears in the display of the driver information system.
Fig. 113 Radio menu
A1
A1
Fig. 114 List of CD
tracks
MODE





 




Basic operation131
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control Would you like to find out more about the media function in your
vehicle? You can find a detailed description on
page 63, “Playing
media”.
Applies to vehicles: with multi-function steering wheel
Selecting a track
Important: A list of tracks must be displayed
page 130,
fig. 114 /
fig. 115.
– Scroll the left thumbwheel
page 128, fig. 110 to mark a
track.
– Press the left thumbwheel to select the track.
Note
You can select a CD in the CD changer or a folder on a portable
player via the MMI control console
page 12.
Applies to vehicles: with multi-function steering wheel
Pausing and resuming (media drive)
Important: A track must be playing
page 63.– Scroll the right thumbwheel all the way down to pause
the track that is currently playing.
– To continue playback, scroll the right thumbwheel
upwards.
Television
Applies to vehicles: with multi-function steering wheel and TV (analog and analog/digital)
Calling up the TV menu
Important: The TV function on the MMI system must be
switched on
page 71.
– Press the button
page 128, fig. 110 repeatedly
until a list of TV channels appears in the display of the
driver information system.
Would you like to find out more about the TV function in your
vehicle? You can find a detailed description on
page 71,
“ Television”.
Fig. 115 Track list of a
folder
Fig. 116 List of TV
channels
MODE





 




Basic operation 132
Applies to vehicles: with multi-function steering wheel and TV (analog and analog/digital)
Selecting a TV channel
Important: A list of TV channels must be displayed

page 131.
– Use the left thumbwheel
page 128, fig. 110 to scroll
up/down and mark a TV channel.
– Press the left thumbwheel to select the TV channel.
The separating line
page 131, fig. 116 distinguishes digital TV
channels from analog TV channels and digital radio stations.
Using the telephone
Applies to vehicles: with multi-function steering wheel and Bluetooth car telephone kit or
phone pre-installation
Introduction
Talking on the phone while driving has become commonplace. Now
you can operate all relevant telephone functions conveniently and
safely on the multi-function steering wheel. For this, your vehicle is
equipped with phone pre-installation or a Bluetooth car telephone
kit.
The following messages can appear on the display of the driver
information system:
A1
A1
Please
wait...Connection with vehicle is being established.
Please
insert
the SIM card
a)
There is no SIM card in the mobile phone.
Reading
SIM carda)The SIM card memory is being scanned.
Please enter
PIN into
MMIThe PIN code has not yet been entered

page 88.
No
connectiona)No network connection
CallReceiving incoming call. If the caller's number
is transmitted with the call, it will also appear in
the display.
BusyNumber dialled is engaged.
Auto
redialThe last number dialled is redialled automati-
cally after a short time.
Telephone
is switched offThe telephone is switched off.
ConnectingEstablishing a connection.











Basic operation133
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control Would you like to find out more about the telephone function in
your vehicle? You can find a detailed description on
page 87,
“Using the telephone”.
Note
•The functions of the telephone can be operated using the multi-
function steering wheel only if the telephone equipment was
installed at the factory.
•The functions of the telephone depend on your mobile phone
and whether they are supported by your mobile network service
provider.
Applies to vehicles: with multi-function steering wheel and Bluetooth car telephone kit or
phone pre-installation
Calling up the telephone menu
Important: The phone pre-installation
page 20 or the
Bluetooth car telephone kit
page 25 must be activated.
– Press the button
page 128, fig. 110 repeatedly
until the telephone menu appears in the display of the
driver information system
fig. 117.
Te l e p h o n e m e n u :
•Dialled no.: Contains the numbers that were dialled last.
•Directory: Contains the entries in the MMI directory
page 80.
•Phone book: Contains the entries on the SIM card.
•Received calls: Contains the calls that were last received.
•Missed calls: Contains recent missed calls.
You can select a number directly from any of these lists.
No
entries
availableThe phone book has no entries or the phone
book entries have not yet been imported into
the on-board phone memory (car telephone kit*

page 29 or phone pre-installation*

page 23).
Telephone
not connected
or attached
a)
The telephone is not connected with the vehi-
cle.
Connect
tel. or
insert SIM card
b)
Insert the SIM card in the handset* or in a
mobile phone with SIM Access Profile or con-
nect the mobile phone to the car telephone kit.
a)Applies to phone pre-installation.b)Applies to car telephone kit and mobile phones with SIM Access Profile.
Fig. 117 Telephone
menu
MODE





 




Basic operation 134
Applies to vehicles: with multi-function steering wheel and Bluetooth car telephone kit or
phone pre-installation
Dialling a telephone number and ending a call
Telephone numbers stored in the phone book, in the direc-
tory and in the call lists can be selected.
Important: The telephone menu must be displayed

page 133, fig. 117.
Placing calls
– Scroll the left thumbwheel
page 128, fig. 110 to select
Dialled no., Directory, Phone book, Received calls or
Missed calls.
– Press the left thumbwheel. A list of entries
fig. 118 will
appear in the display of the driver information system.
– Scroll the left thumbwheel to select an entry.
– Press the left thumbwheel. The telephone number will be
dialled.Placing a further call*
23)
– Scroll the left thumbwheel
page 128, fig. 110 to select
Hold.
– Press the left thumbwheel. The call will then be placed on
hold.
– Press the button
page 128, fig. 110 repeatedly
until the telephone menu appears in the display of the
driver information system
page 133, fig. 117.
– Scroll the left thumbwheel to select one of the call lists,
the phone book or the directory.
– Press the left thumbwheel. A list of entries
fig. 118 will
appear in the display of the driver information system.
– Scroll the left thumbwheel to mark the stored entry you
wish to select.
– Press the left thumbwheel. All phone numbers stored for
the selected entry will be shown.
– Scroll the left thumbwheel to select a phone number.
– Press the left thumbwheel. The telephone number will be
dialled. The current audio source will be muted.
Ending calls
– Scroll the left thumbwheel to select End call and press
the left thumbwheel.
Placing calls
You can enter a number which has not yet been stored via the MMI

page 90 or the handset*
page 145.
Fig. 118 Selecting a
number from the
phone book
23)Applies to car telephone kit and mobile phones with SIM Access Profile.
MODE





 




Basic operation135
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control Placing a further call*
23)
You can call a stored phone number while another call is on hold.
Press the control button for End call to end whichever call is
currently active.
When you have ended the current call, the call that was holding
remains on hold. Select Resume
page 136 to continue with the
call that is on hold.
Use the option Switch
page 136 to go back and forth between
two calls.
Note
•You can use the multi-function steering wheel to dial only those
numbers that have been stored beforehand. Use the MMI control
console to dial a new number
page 90.
•If you activate the voice guidance option off (phone)* in the navi-
gation* function you will not hear any navigation cues while you are
talking on the telephone*
page 119.
Applies to vehicles: with multi-function steering wheel and Bluetooth car telephone kit or
phone pre-installation
Answering and ignoring telephone calls
Important: There must be an incoming call.Answering telephone calls
– Press the left thumbwheel
page 128, fig. 110.
Ignoring telephone calls
– Scroll the left thumbwheel to select Ignore and press the
left thumbwheel.
Depending on whether the caller is stored in the phone book and
whether the number is transmitted with the call, the name, the tele-
phone number or Unknown will appear in the driver information
system.
Applies to vehicles: with multi-function steering wheel, Bluetooth car telephone kit and
mobile phone with SIM Access Profile
Options during a call (car telephone kit)
Certain options can also be selected using the multi-function
steering wheel. The available options will be displayed in the driver
information system.
The options available during a call depend on the current telephone
status. For example, if you have placed a call on hold, the Hold
option will be replaced by Resume.
Fig. 119 Incoming call
Fig. 120 Replacing a
call





 




Basic operation 136
Holding/resuming a call
You can use the left thumbwheel on the multi-function steering
wheel to place a call on hold.
Select Hold to hold the call and Resume to continue talking. The call
on hold is displayed in the driver information system.
Switching between calls
You can switch between two phone calls (one of them will be on
hold at any given time).
Should you receive a second call during a phone conversation, the
option Switch will appear in the driver information system display.
Select Ignore if you don't want to receive the call.
Select End call to end whichever call is currently active. The call on
hold will remain in the hold queue and can be continued by
selecting Resume.
Replacing a call
If you already have a call on hold and are talking to a second caller
when a third call is received, the options Replace and Ignore will
appear on the display of the driver information system.
If you select Replace, the active call will be replaced by the incoming
call. If you select Ignore, the incoming call will be declined. The call
on hold will remain in the hold queue.
Note
The option Call waiting must be activated on the MMI
page 97 for
you to be made aware of incoming calls during a conversation. The
call options depend on your mobile network service provider. For
more information, contact your service provider.
Applies to vehicles: with multi-function steering wheel and phone pre-installation
Options during a call (phone pre-installation)
If you are already talking on the phone when someone else calls, the
options Replace and Ignore will appear on the display of the driver
information system.
If you select Replace, the active call will be replaced by the incoming
call. If you select Ignore, the incoming call will be declined. The call
on hold will remain in the hold queue.
Note
The option Call waiting must be activated on your mobile phone for
you to be made aware of incoming calls during a conversation. The
call options depend on your mobile network service provider. For
more information, contact your service provider.
Navigation
Applies to vehicles: with multi-function steering wheel and navigation system
Calling up the navigation menu
Important: The navigation function on the MMI system
must be switched on
page 105.
Fig. 121 Navigation in
the driver information
system





 !




Basic operation137
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control
– Press the button
page 128, fig. 110 repeatedly
until the navigation menu appears in the display of the
driver information system
page 136, fig. 121.
Would you like to find out more about the navigation function in
your vehicle? You can find a detailed description on
page 104.
Applies to vehicles: with multi-function steering wheel and navigation system
Repeating voice guidance cues
– Press the right thumbwheel to have the last route
guidance cue repeated
page 128, fig. 110.
Vo i c e c o n t r o l
Applies to vehicles: with multi-function steering wheel and speech dialogue system or
telephone speech control system
Switching the speech dialogue system /
telephone speech control system on and off
Switching on
– Press the button .Switching off
– Press and hold the talk button until you hear the cue
<Cancel>.
The system will give a beep tone when it is ready to begin with a
dialogue. The desired functions can then be accessed with speech
commands.
Note
For a more detailed description, please refer to the chapter on

page 169, “Speech dialogue system” or
page 161, “Basic oper-
ation”. If your vehicle is not equipped with the speech
dialogue/control system, this button has no function.
MODE
AD
Fig. 122 Multi-func-
tion steering wheel:
Ta l k b u t t o n
A3
A3





 




138