sensor AUDI A5 CABRIOLET 2017 Owner's Guide

a:,
a:,
...... N r--. N ...... 0
0
LL 00
-the e lectron ic control modu le and externa l side
impact sensors
- the two side airbags located in the sides o f the
front backrests
- the a irbag warning light in the inst rument cl us-
ter.
The a irbag system is monitored electronically to
make certa in that it is func tioning properly at all
times. Each time you turn on the ignit ion, the air­
bag system indicator light will come on for a few
seconds (self diagnostics).
The s ide a irbag system supp lements the safety
be lts and can help to reduce the risk of injury to
the driver's and fron t passenger 's upper torso on
the side of the vehicle that is struck in a side col­ lision. The airbag d eploys on ly in side impacts
and only when the veh icle acceleration reg istered
by the contro l unit is high enough. If this rate is
below the reference value programmed into the
control un it, the s ide a irbags w ill not be tr ig­
gered, even though the car may be badly dam­
aged as a resu lt of the collision .
It is not possib le
to define an airbag trigge ring range that w ill cov­
e r every possible angle of impact, since the ci r­
cumstances wi ll vary considerably between one
collision and another. Important factors include,
for examp le, the nature (hard or soft) of the im ­
pacting objec t, the ang le of impact, vehicle
speed, etc. ¢
page 148, Impor tant safety in­
structions on the side airbag system .
Aside from their normal safety function, safety
be lts work to help keep the driver or front pas­
senger in posit ion in the event of a side collision
so that the s ide a irbags can provide protection .
T he airbag system is
not a substitute for your
safety belt. Rather, it is part of the overa ll occu­
pant restrain t system in your veh icle. Always re­
member that the s ide a irbag system can only
h elp to protect yo u if you a re wearing your safety
be lt and wea ring it properly. This is another rea­
son why you s hou ld always wear yo ur safety
be lts, not just bec ause the law req uires yo u to do
so ¢
page 122 , General information.
It is important to remember that wh ile the s up­
p lemental s ide a irbag system is designed to re­
d uce the likelih ood of serious injur ies, other inju-
Airb ag sys tem
ries, for example, swelling, bru is ing , and minor
abrasions can also be associated wit h deployed
s ide airbags . Remember too, s ide airbags will de­
ploy only once and only in certain k inds of acci­
den ts -your safety belts are always there to offer
protect io n.
Vehicle damage, repair costs or even the lack of
vehicle damage are not necessar ily an ind ication
of over-sens it ive or fa iled a irbag activation. In
some collisions, both front and side airbags may i nflate. Remember too, that a irbags w ill deploy
only once and only i n certa in kinds of collisions -
you r safety be lts are always there to offer protec­
t ion in those accidents in wh ich airbags are no t
s u pposed to deploy or when they have already
deployed .
The side airbag system will not deploy:
-when t he ignit ion is t urned off
- in side collisions whe n the acceleration meas-
ured by the sensor is too low
- in front -end coll is ions
- in rear-end collisions
- in rollovers.
In some types of accidents the fron t air bags and
s ide airbags may be triggered togethe r.
.&, WARNING ~
- Safety belts and the airbag system will only
provide protect ion when occupants are in
the proper seat ing pos ition ¢
page 148 .
-If the ai rbag ind icator light¢ page 17
comes when the veh icle is being used, have
the system inspected immediately by your
author ized Audi dealer. It is possib le that
the airbag will inflate when it is not sup ­
posed to, or w ill not inflate w hen it should .
147

a:,
a:,
...... N r--. N ...... 0
0
LL 00
by being pushed into you as the airbag in­
flates.
- Never place or attach accessories or other
objects (such as cupholders, telephone
brackets, or even large, bulky objects) on
the doors, over or near the area marked
"AIRBAG" on the seat backrests.
- Such objects and accessories can become
dangerous projectiles and cause injury
when the supplemental side airbag de­
ploys.
- Never carry any objects or pets in the de­ ployment space between them and the
airbags or allow children or other passen­
gers to travel in this position.
- Always prevent the side airbags from being
damaged by heavy objects knocking against
or hitting the sides of the seatbacks.
- The airbag system can only be triggered
once. If the airbag has been triggered, the
system must be replaced by an authorized
Audi dealership.
- Damage (cracks, deep scratches etc.) to the
original seat covers or to the seam in the
area of the side airbag module must always
be repaired immediately by an authorized
Audi dealer.
- If children are seated improperly, their risk
of injury increases in the case of an accident
~ page 150, Child safety.
-Never attempt to modify any components of
the airbag system in any way.
- In a side collision, side airbags will not func­
tion properly if sensors cannot correctly
measure increasing air pressure inside the
doors when air escapes through larger, un­
closed openings in the door panel.
- Never drive with interior door trim panels
removed.
- Never drive when parts have been re­
moved from the inside door panel and the
openings they leave have not been proper­
ly closed.
- Never drive when loudspeakers in the
doors have been removed unless the
speaker holes have been properly closed.
- Always make certain that openings are
covered or filled if additional speakers or
Airbag system
other equipment is installed in the inside
door panels.
- Always have work on the doors done by an
authorized Audi dealer or qualified work­
shop.
149

a:,
a:,
...... N r--. N ...... 0
0
LL 00
exceptional circumstances and the PASSEN·
GER AIR BAG OFF
light does not come on
and stay on, immediately insta ll the rear­
ward-facing child safety seat in a rear seat­
ing posit ion and have the airbag system in­
spected immediately by your authorized
Audi dealer.
A WARNING
If, in except ional circumstances, you must in­
stall a forward-facing chi ld restraint on the
front passenger's seat :
- Always make sure the forward-fac ing seat
has been designed and certified by its man­
ufacturer for use on a front seat with a pas­
senger front and s ide airbag .
- Always follow the manufac turer 's instruc­
tions provided with the chi ld safety seat or
carrier.
- Always move the passenger seat into its
rearmost position in the seat's fore and aft
adjustment range, as far away from the air­
bag as possib le before installing the child
restra int. The backrest must be adjusted to
an upr ight position.
-Always make sure that the
PA SSENGER AIR
B AG OFF
light comes on and stays on all the
t ime whenever the ignition is switched on.
Always replace ch ild restraints that were in­
stalled in a vehicle dur ing a crash. Damage to
a child restraint that is not visib le could cause
it to fail in another collision situation.
Advanced front airbag system and children
Your veh icle is equipped with a front "Advanced
A irbag System" i n compliance w ith United States
F edera l Moto r Vehicle Safety Standard ( FMVSS)
208, as well as Canada Motor Ve hicle Safety
Standard (CMVSS) 208 as applicable at the time
your vehicle was manufactured .
The Advanced Airbag system in your ve hicle has
been ce rtified to meet the " low-risk" requ ire­
ments for 3 -and 6-yea r old children on the pas ­
senger side and sma ll adults on the driver side .
Child safety
The low risk deployment criteria a re intended to
reduce the risk of injury through interaction with
the a irbag that can occur, for example, by be ing
too close to the steering wheel and instrument panel when the airbag inflates. In addition, the
system has been certified to comply with the "suppression" requirements of the Safety Stand·
ard, to turn off the front airbag for infants up to
12 months who are restrained on the front pas­
senger seat in ch ild rest raints that are listed in
the Standard.
Even though your veh icle is equipped with an Ad·
vanced Airbag system, all ch ild ren, especially
those 12 yea rs and you nger, sho uld a lways ride
in the back seat proper ly restrained for their age
and size . The airbag on the passenger side makes
the front seat a potentially dangerous p lace for a
child to ride. The front seat is not the safest place
for a ch ild in a forward-fac ing ch ild safety seat. It
can be a very dangerous place for an infant or a
larger ch ild in a rearward-facing seat .
' Advanced Airbags and the weight-sensing
mat in the front seat
The Advanced A irbag System in your vehicle de ­
tects the presence of an infant or chi ld in a chi ld
restraint on the front passenger seat using the
weight -sensing mat in the seat cushion and the
sensor below the safety belt latch on the front
passenger seat that measures the tens ion on the
safety belt.
The weight-sensing mat measures total weight of the child and the chi ld safety seat and a child
blanket on the front passenger seat . The weight
on the front passenger seat is related to the de­
s ign of the child restra int and its "footprint", the
s ize and shape of the bottom of the ch ild re-
straint as it sits on the seat. The weight of a ch ild
restra int and its "footprint" va ry for different
k inds of child restra ints and for the different
models of the same kind o f chi ld rest raint of -
fered by chi ld restraint manufacturers.
T he we igh t ranges for the indiv id ual types,
makes and mode ls of ch ild restraints that the
NH TSA has specified in the Safety Standard to­
gether with the weight ranges of typical infants .,.
15 1

a:,
a:,
...... N r--. N ...... 0
0
LL 00
Off-Road driving?
Your Aud i does not have enough g ro und clear­
ance to be used as an off -road vehicle. It is there ­
fore best to avoid roug h tracks and uneven ter­
rain as much as possible. A lso refer to
¢ page 175.
_&. WARNING
Always adjust you r driving to road and t raff ic
conditions. Do not let the extra safety afford­
ed by all-wheel drive tempt you into tak ing
extra risks.
-Although the all-whee l dr ive is very effec­
t ive, a lways remember that bra king capac ity
is limited by tire traction . Yo u should there­
fore not d rive a t exc ess ive speeds on icy or
slippery road su rfaces.
- On wet ro ad surfaces, be caref ul not to drive
too f ast be cause the fro nt wheels co uld be­
gin to slide on top of the w ater ( aquaplan ­
ing). If this sho uld o ccu r, you w ill have no
warning from a sud den increase in eng ine
speed as with a front-whee l dr ive vehicle .
Always drive at speeds wh ich are su ited to
the road cond it ions -risk of crash.
Energy management
Starting ability is optimized
Energy management controls the distribution of
electrical energy and thus optimizes the availa­
bility of electrical energy for s tarting the engine.
If a veh icle wit h a conventional energy system is
not driven for a long per iod of t ime, the battery is
d ischa rged by idling current consumers (e.g. im­
mo bilizer). In cert ain cir cums tan ces it c an result
i n there be ing insuff ic ient ene rgy available to
start the engine.
I ntell igen t energy management in your veh icle
h andles the distr ib ution of ele ct ric al ene rgy.
S tarting ab ility is mar ked ly imp roved an d the l ife
of the batte ry is extended.
B asically, e nergy management consis ts of
bat­
tery diagno sis, idling curr ent management
and
dynamic energy management .
Intelligent Technology
Battery diagnosis
Battery diagnos is con tinuously dete rmi nes the
state o f the bat tery . Sensors determine battery
vo ltage, battery c urrent and batte ry tempera­
tu re. This determines t he current state of charge
and the power of the battery.
Idling current management
Id ling cur rent management reduces ene rgy con­
s u mption whi le the vehicle is standing . With the
ignition switched off, it contro ls the energy sup­
ply to the vario us electrical components . Data
from battery d iagnosis is cons idered.
Depend ing on the ba ttery's s tate of charge, indi ­
vidual consumers are gradually turned off to pre­
vent excess ive discharge of t he battery and thus
mainta in starting capab ility.
Dynamic energy management
While t he vehi cle is being d riven, dynami c energy
management dis trib utes the energy generate d
according to the needs of the individual compo­
nents. It regulates consumption, so that more
electrical e nergy is not being used than is being
generated and ensures an opt imal state of
charge for the battery .
(i) Tips
-But even ene rgy management cannot neg­
ate the lim its of physics. Consider that the
powe r and life of a battery are lim ited.
- If starting ab ility is threatened, the indica ­
to r li ght (•) appears¢
page 14.
What you should know
The highest priority is given to maintaining start­
ing capability.
The battery is severe ly taxed in short-distance
driv ing, in city traffic and dur ing the cold time of
year. Abundant e lectrica l energy is required, but
o n ly a little is generated. It is also c ritical if the
engi ne is not running and electrical components
are tu rned on . In this instance energy is being
co nsumed bu t no ne is being ge nerated. .,,.
173

Care and cleaning
Care and cleaning
General information
Regular, prope r care helps to maintain your vehi ­
cle's value.
It can a lso be a requirement when
submitting war ranty claims for cor rosion damage
and pa int defects on the body.
The necessary care prod ucts can be obtained
from an autho rized Audi deale r or authorized
Aud i Service Facility. Read and follow the instruc­
tions for use on the packaging.
A WARNING
- Using clean ing and care products incorrectly
can be dangero us to your hea lth .
- Always store clean ing and care products out
of reach of children to reduce the r isk of po i­
so ning.
@ For the sake of the environment
- P referab ly purchase env ironmenta lly-friend­
l y cleaning products.
- Do not dispose of leftove r clean ing and care
products wit h household t rash.
Car washes
The longer that deposits remain on the veh icle,
the more the surface may be damaged. High
temperatures such as those caused by sunlight
increase the damaging effect.
Before washing, rinse
off heavy depos its with
p lenty of water.
Stubborn deposits s uch as bird d roppings or tree
sap are best removed with plenty of water and a mic rofibe r cloth.
A lso, wash the und erside of yo ur vehicle o nce
road sa lt stops being used for the season .
Pressure washers
When washing your veh icle w ith a pressure wash­
er, always follow the operating instructions pro ­
vided wi th the press ure washer. This is espe cially
impor tant i n rega rd to the pressure and spraying
d istance. Do not direct the stream of water di­
rectly onto seals for the side windows, doors,
182
lu ggage compartment lid or hood or onto the
tires, rubber hoses, insulating material, the pow­
er top, sensors* or camera lenses* . Keep a dis­
tance of at least 16 inches (40 cm).
Do not remove snow and ice with a pressure
washer.
Neve r use cone nozzles or high press ure nozzles.
The wate r temperatu re must not be above 140 °F
(60 °() .
Automatic car washes
Spray off the vehicle before washing.
Make sure that the win dows and power top are
closed and the windsh ield wipers are off. Follow
i nst ruct ions from the car wash operator, espe­
c ia lly if there are accessories attached to yo ur ve­
hicle.
If possible, use car washes that do not have
brushes.
Washing by hand
Clean th e ve hicle star ting from the top and work­
i ng down using a soft sponge or clea ning brus h.
Use solvent -free cleaning products.
Washing vehicles with matte finish paint by
hand
To avo id damaging the paint when washing, fi rst
remove dust and large pa rticles from your vehi­
cle. Insects, grease spots and f ingerprints are
best removed w ith a special cleaner for matte
finish paint.
Apply t he product using a microf iber cloth. To
avo id damaging the paint surface, do not use too
much pressure.
Rinse the ve hicle thoroughly with wate r. Then
clean using a neutra l shampoo and a soft micro ­
fiber clot h.
Rinse the vehicl e thorough ly again and le t i t air
d ry. Remove any water residue using a chamois.
A WARNING
- Only wash the vehicle when the ignition is
off and follow the instr uctions from the car
-

a:,
a:,
...... N r--. N ...... 0
0
LL 00
wash operator to reduce the risk of acc idents.
- To reduce the risk of cuts, protect yourself
from sharp metal components when wash­
ing the underbody or the inside of the wheel
housings .
- After washing the vehicle, the brak ing effect
may be delayed due to mo isture on the
brake rotors or ice in the w inter . This in­
c reases the risk of an acc ident. The bra kes
must be d ried fi rst w ith a few careful b rake
applications.
(D Note
- If you wash t he vehicle in an automatic car
wash, yo u m ust fold the exte rior m irrors in
to reduce the risk of damage. Power fo ld ing
exter ior mir ro rs* m ust only be folded in and
out using t he power folding fu nction .
- To reduce the risk of paint damage, do not
wash the vehicle in d irect sunlig ht.
- To reduce the risk of damage, do not wash
th e power top wit h a press ure washe r.
Ca re and cleaning
- To re duce the risk of damage to the surface,
do not use insect removing sponges, kitchen
sponges or s imilar items .
- Matte finish painted veh icle components:
- To reduce the risk of damage to the sur-
face, do not use po lishing agents or hard
wax.
- Never use protective wax . It can destroy
the matte finish effect .
- Do not place any stickers or magnetic
signs on vehicle parts painted with matte
finish paint . The paint cou ld be damaged
when the stickers or magnets are re­
moved .
@ For the sake of the environment
Only wash the vehicle in facili ties s pec ia lly de­
s igned for that pu rpose. This will reduce the
r isk of dir ty wate r contam ina ted with o il from
en te ring the sewe r sys tem.
Cleaning and care information
When cleaning and caring for individua l vehicle
components, refer to the follow ing tables. The
in fo rmat ion conta ined there is s imp ly recom­
mendations . Fo r q uest ions or for components t
h at are not listed, consult an autho rized Aud i
dealer or authori zed Audi Se rvice Fac il ity. Also
f o llow the information fo und in ~ &, .
Exterior cleaning
Component Situation
Solution
Windshield wiper
Deposi ts ~ page 54, Cleaning windshield wiper blades
blades
Headlights/ Tail
Deposits Soft sponge with a m ild soap solutiona)
lights
Sensors /camera
Deposits Sensors: soft cloth wit h solvent-free cleaning solution
lenses Camera lenses: soft cloth w ith alcohol-free cleaning solu-
tion
Snow/ice Hand br ush/solven t-free de-icing spray
Wheels Road salt Water
Brake dust Acid-free s
pecial clean ing so lu tion
E x haust tail pipe s Road salt Water, cleaning solution su itab le for stainless stee l, if nee -
essary
183

Check ing and F illing
The location of the coolant expansion tank can be
seen in the engine compartment illustration
¢ page 195.
To obtain an accura te reading, the eng ine must
be switched off .
The expans io n tank in your vehicle is equipped
with a n elec tric coolant level sensor.
When the coolant level is too low, the war ning
lig ht in the Auto-Check System¢
page 15 will
blin k until you add coo la nt and the level has bee n
restored to normal. Even t hou gh the re is an e lec­
tr ic coolant level sensor, we still re commend you
check the coo lant level from time to time .
Coolant loss
Coolant loss may indicate a leak in the cooling
system. I n the event of coolant loss, the cooling
system should be inspected immediately by your
author ized Audi dealer. It is not enough me rely
to add coolant.
I n a
se aled system, losses can occur only if the
boi ling point of the coo lant is ex ceeded as a re ­
sul t of over heat ing.
A WARNING
T he cooling system is unde r pressure and can
get very hot . Red uce the risk of scalding from
hot coolant by following these steps.
- Turn off the eng ine and a llow it to cool
down .
- Protect your face, hands and arms from es ­
caping fluid and steam by cove ring the ca p
with a la rge, thick rag.
- Turn the cap s lowly and very ca refu lly in a
counter-clockwise direction w hile ap ply ing
light, downwa rd pressure o n the top of the
cap.
- To avo id being burned, do not sp ill anti­
freeze or coolant on the exha ust system or
hot eng ine parts. Under certain conditions,
the ethy lene g lycol in e ngine coolant can
catch fire.
(D Note
Do not add any type of radiato r leak sealant
to your veh icle's engine coolant. Adding radia-
200
tor repair fluid may a dverse ly affect the func ­
tion and performance of your coo ling system
and could result in damage not covered by
your New Vehicle Limited Warranty.
Adding coolant
Be very careful when adding engine coolant.
Befo re yo u check any thing in the engine compart­
ment,
always read and heed all WARNINGS
¢ A in Working in the engine compartment on
page 193.
Requireme nt: The re mus t be a res idual amo unt
of coolant in the expans ion tank ¢(!) .
""Tur n off t he engine .
"" Let the eng ine cool down.
"" Pla ce a thick rag over the coolan t ex pan sio n
tank ¢
page 199, fig. 174 and carefull y turn
the cap counter-clockwise ¢,&. .
"" Add coolant m ixed in the cor rect rat io
¢page 199, Coolant up to the MAX ma rking.
"" Make sure that the fluid level remains stab le.
Add more coolant if necessa ry .
"" Twis t the cap o n aga in
tightly.
Replacement eng ine coolant must conform to ex­
act specifications ¢
page 199, Coolant.
We recommend using only coo lant ad ditive G 12+
+ , G13 or in an emergency G12+. Do
not use a
different additive. In an emergency use plain wa­
te r unt il you can get the cor rect addit ive and ca n
r esto re the cor rect rat io. Thi s should be done as
soon as possib le.
If you have lost a considerable amount of coo l­
an t, then you s hou ld add co ld a ntifreeze and cold
water only whe n the engine is co ld.
A lways use
new engine coo lant when ref illing.
Do no t fill c oolant above the "MAX" mark . Excess
coolant will be forced out th rough the pressure
r elief valve in the cap when the engine becomes
hot.
~

a:,
a:,
...... N r--. N ...... 0
0
LL 00
check your tires as soon as possible, and inflate
them to the proper pressure. Driving on a signifi­
cantly under-inflated tire causes the tire to over­
heat and can lead to t ire failure. Under-inflation
a lso reduces fuel efficiency and tire tread life,
and may affect the vehicle 's handling and stop ­
p ing ability .
Please note that the TPMS is not a substitute for
proper tire maintenance, and it is the driver's re­
sponsib ility to ma intain correct tire pressure,
even if under-inflation has not reached the level
to tr igger illum inat ion of the TPMS low tire p res­
sure telltale.
Your veh icle has also bee n eq uipped w ith a TPMS
malfunct ion indicator to indicate when the sys­
tem is not operat ing properly . The TPMS ma l­
function ind icator is combined w ith the low tire
p ressure tellta le. Whe n the system detects a
malfunct ion, the te lltale will flash fo r approx i­
mately one mi nute and then remain continuo usly
illuminated. This sequence will continue upon
subseq uent veh icle start-ups as long as the ma l­
function ex ists .
When t he malfunction indicator is ill uminated,
the system may not be ab le to detect or signal
l ow tire press ure as intended. TPMS ma lf u nctions
may occur for a var iety of reasons, including the
installation of replacement or alternate t ires or
wheels on the vehicle that prevent the TPMS
from functioning properly . Always c heck the
TPMS malfunction telltale afte r rep lacing one o r
mo re t ires o r whee ls on your ve hicl e to e nsur e
th at t he replacement or al tern ate tir es and
wheels a llow the TPMS to con tinue to function
p roperly .
Wheel s
If the Tire Pressure Monitoring System
indicator appears
Applies to : vehicles wi th Tir e Pressure Monito ring Syste m
Th e tire pressure indicator in th e instrument
cluster informs you if the tire pressure is too low
or if there is a system malfunction.
Fi g. 182 Instrument cl uster: indic ator lig ht w ith message
U sing the ABS sensors, the t ire pressure monito r­
i ng system compares the tire tread c ircumfer­
ence and v ibration characterist ics of the ind ividu ­
al tires. If the press ure changes in one or more
t ir es, th is is indicated in the instrument cluster
display with an indica to r li gh t
IE and a message.
If only one tire is affected, the loc ation of tha t
t ir e will be indicated.
T he t ire press ures mus t be stored in the Infota in­
me nt system again each time t he pr essures
c h ange (switching between parti al and full load
pressure) or afte r changing or replac ing a tire on
yo ur vehicle ¢
page 226 . The tire p ressure moni­
toring system on ly monitors the tire pressure you
have stored. Re fer to the t ire pressure label for
the recommended t ire pressure for yo ur vehicle
r=> page217, fig.181.
T ire tread c irc umference and vibration character ­
istics can change and ca use a tire press ure warn­
ing if :
- the tire pressure in one or more tires is too low.
- t he t ire h as str uctural damage.
- t he t ire w as re pla ce d or the t ire pressu re was
ch anged and it was no t store d ¢
page 226 .
- the spare tire* is i nstalled .
Indicator lights
IE Loss of pressure in at least one tire¢.& .
Check the tires and replace or repair if necessary .
IJJ,,
225

Tires with unidirectional tread design
Tires with unidirectional tread design must be
mounted with their tread pattern pointed in the
right dir ection .
Using a spare tire with a tread pattern
intended for use in a specific direction
When us ing a spa re t ire with a tread pa tte rn in­
tended fo r use in a specific direction, please note
the following:
- The direct ion of rotat io n i s marked by an
arrow
on the side of the tire .
-If the spare tire has to be installed in the incor­
rect d irection, use the spare tire only tempora ­
rily s ince the tire w ill not be ab le to achieve its
opt imum performanc e ch arac teristics with re­
gar d to a quaplaning, noise and wea r.
- We recommend that you pay particular atten­
t io n t o this fac t during we t weat he r and that
yo u a dju st yo ur speed to match road condi ­
t ions.
- Replace the fla t tir e with a new one and have i t
i ns ta lled on yo ur vehicle a s soon as possible t o
res tore the handling advantages of a unid irec­
t iona l tire .
Notes on wheel changing
Please read t he info rmation ¢ page 214, New
tires or wheels
i f you are going to use a spare tire
which is different from t he tires on your vehicle.
Afte r you change a tire:
- Check the tire pressure on the spare immedi­
ately after installation .
- Have the wheel bolt tightening torque
checked with a torque wrench as soon as pos­
sible by your authorized Audi dealer or quali­
fied workshop.
- With steel and alloy wheel rims, the wheel
bolts are correctly tightened at a torque of 90
ft lbs. (120 Nm).
- If you notice that the wheel bolts are corroded
and difficult to turn while changing a tire ,
gi they should be replaced before you check the ......
~ tightening torque.
N ...... 0
0
LL 00
Emergency assistance
-Replace the flat tire with a new one and have
it installed on your vehicle as soon as possi­
ble. Remount the wheel cover .
Until then , drive with extra care and at reduced
speeds.
_& WARNING
- If you are going to equip yo ur vehicle with
tires or r ims which differ from those wh ich
were factory installed, then be sure to read
the information
c> page 214, New tires or
wheels.
- Always make sure the damage d w heel or
even a flat tire and the jack and tool kit are proper ly secured in the luggage compart­
men t an d ar e not loose in the passenger
compa rtme nt.
- In an accident or sudde n maneuver they
coul d fly forward, injuring a nyo ne in t he ve­
h icl e.
- Always s tore damaged w heel, jack and tools
secure ly i n t he lu ggage compartmen t. Ot h­
e rw ise, in an accident or sud den m aneuve r
they could fly forward, causing injury to pas ­
sen gers in t he veh icle.
(D Note
D o no t use c omm erc ially ava ilable tire se al­
a nts. Otherwise, t he e lectr ical comp onents of
the tire p re ssu re m on ito ring syst em * w ill no
l on ger wor k pro perly and t he sensor fo r the
tire p ressure monito ring system* wi ll have to
b e replaced by qualifie d wo rkshop .
-
233

a:,
a:,
...... N
" N ...... 0
0
LL co
Fuse panel @ (black)
No . Consumer
1 Dynamic steering
2 Electronic Stabilization Cont rol (mod ule)
A/C system press ure sensor, elect rome -
chan ica l park ing brake , Homelink, auto-
3 mat
ic dimming interior rear v iew mirror,
air q uality/outside a ir sensor, Electronic
Stabili zation Cont rol (button)
5 Sound actuator
6 Headlight range control/
headlight (cor-
ne ring light)
7 Headlight (cornering light)
Con trol modules (e lectrom echan ica l par k-
8 ing brake, s hock ab so rbe r, q uattro s port),
DCDC converter
9 Adapt ive cru ise control
1 0 Shift ga te/clu tch se nsor
1 1 Side assist
12 Headlight range control
, p arkin g sys tem
13 Airbag
14 Rear wiper (a
llroad)
1 5 Auxiliary fuse (instrument panel)
1 6 Auxiliary fuse terminal 15 (engine area
)
Fuse panel@ (brown)
No . Consumer
2 Brake light senso r
3 Fuel pump
4 Clutch sensor
5
Left seat heating w it h /w it h out seat venti-
l a tion
6 Electronic Stabili zation Cont rol (e lectr ic)
7 Ho rn
8
Front left door (window regulator, central
locki ng, mirror, switch, lig hting)
9 Windshield wiper moto r
10 Electronic Stabilization Cont rol (va lves)
Fuses and bulbs
No . Consumer
Two-door mode ls: rear left w indow reg ula-
1 1 tor; Four-door mode
ls: rear left door (w in-
dow regu lator, central locking, switch,
li ght ing)
1 2 Rain and
light sensor
Fuse panel © (red)
No . Consumer
3 Lumbar support
4 Dynam ic steering
5 Inter
io r ligh ting ( Cabr io let)
6 W
indshie ld washer system, headlight
wash er system
7 Vehicle e lectrica l system control module 1
8 Ve hicl e e lec trica l sy stem con trol module 1
9
Left rear window regu lator motor (Cabr io-
l et)/s unroof
1 0 Vehicle e lec tric al system con trol module 1
1 1 R
ight rear window regulator (Cabriolet)/
su n shade motor
1 2 A
nti- theft alarm warning system
Right cockpit fuse assignment
Fig. 194 R ig h t cockp it : f use pane l wit h plast ic cl ip
235