transmission AUDI A6 1995 C5 / 2.G 01E Transmission Final Drive Rear Remove And Install Workshop Manual

39-102


Rear final drive, removing and
installing

Special tools, testers and auxiliary items

Universal support V.A.G 1359/2
Engine/transmission jack V.A.G 1383 A

Removing

- Remove rear section of exhaust system
(rearward of exhaust pipe clamp(s)):

Repair Manual, 2.7 Liter V6 5V BiTurbo
Engine Mechanical, Engine Code(s): APB, Repair Group 26


- Remove heat shield above driveshaft.
Pa
ge 1 of 8 Rear final drive, removin
g and installin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM03.39.14

39-104


- Support final drive with transmission jack V.A.G 1383 A and universal
support V.A.G 1359/2.
- Secure final drive with a strap.

- Unscrew bolts (arrows) on front cross member for rear final drive.
- Disconnect front cross member.
Pa
ge 3 of 8 Rear final drive, removin
g and installin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM03.39.14

39-105


Note:
The cross member -1- need not be removed.
Installing
Installation is carried out in the reverse order, when doing this observe the
following:
Note: - Unscrew securing bolts -B- and -C- of rear cross member on rear final
drive.
- Lower final drive on transmission jack.
Always replace self-locking nuts.It is essential to clean out the locking fluid remaining in the threads in
the drive flange on the rear final drive after removing the driveshaft.
Otherwise there is a danger that the new bolts will seize when they
are screwed in and then shear if they have to be removed later. The threaded holes can be cleaned with a thread tap.Replace gasket between driveshaft and drive flange (pull off backing
foil and stick gasket onto drive flange). Surface must be free of
grease. Replace driveshaft bolts (self-locking).
Pa
ge 4 of 8 Rear final drive, removin
g and installin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM03.39.14

39-106


Note: - Raise final drive with transmission jack until both drive axles can be
connected.
- Lightly tighten securing bolts for drive axles.
- Lift final drive and bolt to cross member and final drive support.
- Bolt on driveshaft Page 39
-71
.

To prevent imbalance, the flanges on the driveshaft -A- and on the
rear final drive -B- must be installed so that the paint markings are in
alignment (arrows). After removing the driveshaft from the rear final drive, the additional
balance disk (thick washer) that may be located between the lock
plate and the bolt head must not be reinstalled. Always replace all
flange bolts after disassembling. Replace driveshaft bolts (self-locking).
Pa
ge 5 of 8 Rear final drive, removin
g and installin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM03.39.14

39-108

Rear final drive, securing to repair stand


Special tools, testers and auxiliary items

Engine/transmission support VW 540

- Secure complete rear final drive to a repair stand with engine and
transmission support VW 540.
Pa
ge 8 of 8 Rear final drive, removin
g and installin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM03.39.14