AUDI A6 1996 C5 / 2.G AHA Engine Multiport Fuel Injection And Ignition System Owners Manual

24-70


Display fields

1 2 3 4
Display group 2: Load measurement
Display xxx RPM xx.xx ms xx.xx ms xx.x g/s
Indicates Engine
speed
(in 40 RPM
steps) Engine load Injection
time Mass air flow
Range 0 - 6800
RPM 0.00 - 12.75 ms 0.00 -
20.00 ms 0.0 - 140 g/s
Specified
value 620 - 740
RPM
(all-wheel
drive)
or
740 - 860
RPM
(front-wheel
drive) 1.00 - 2.50 ms 2.00 - 5.00
ms 2.8 - 5.6 g/s

2520 RPM 0.80 - 2.50 ms 1.60 - 5.00
ms 10.0 - 15.0 g/s
--- If not as specified page 24
-71
,
--- If not as specified page 24
-72
,
Pa
ge 91 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

Evaluation of display group 2, display
field 2 Evaluation of display group 2, display
field 4
If displayed values are OK (as specified):

-
Press button to advance program
sequence.
- Press buttons -0- and -6- to select "End Output"
function 06, and press -Q- button to confirm
input.

- Switch ignition off.
Pa
ge 92 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-71
Evaluation of display group 2, display field 2 Display group:
2


Display field:
2
Possible malfunction cause
Corrective action
less than 1.00
ms
Smaller values can only occur while driving during
deceleration
more than 2.50
ms Shift lever in drive range (auto. transmission)
Engine is affected by additional consumers- Move shift lever into P or N
- Eliminate load (A/C, power steering, generator)

Poor idle (does not run on all cylinders)- Check and spark plugs page 28
-21
(checking
ignition coils)
- Check fuel injectors page 24
-102


Throttle valve control module -J338- faulty- Check throttle valve control module page 24
-
128

Pa
ge 93 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-72
Evaluation of display group 2, display field 4 Display
group: 2


Display field:
4
Possible malfunction cause
Corrective action
less than 2.8
g/s
Large amount of false air between intake air duct and
Mass Air Flow (MAF) sensor - Check intake air system for leaks (false
air) page 24
-126

larger than 5.6
g/s
Shift lever in drive range (auto. transmission)
Engine affected by additional consumers- Move shift lever into P or N
- Eliminate load (A/C, power steering,
generator)

Open circuits in wire 1 or 2 between MAF sensor and
ECM - Check voltage supply page 24
-73


Open circuit in wire 3 between MAF sensor and relay
panel - Check wiring page 24
-73
Pa
ge 94 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-73

Checking voltage supply

If there is no voltage:
Checking wiring - Disconnect 3-pin harness connector from Mass Air Flow sensor (MAF).
- Connect multimeter US1119 (Fluke 83 or equivalent) between harness
connector terminals 2 (Ground) and 3 (B+), using adapter cables from
VW1594 connector test kit.
Specified value: 9.0-14.5 volts
- Switch ignition off.
- Check wiring using applicable wiring diagram.
- Switch ignition off.
- Connect VAG1598/22 test box to ECM harness connector page 01
-
67
.
- Check wiring for open circuits, between ECM/test box and 3-pin MAF
sensor harness connector.

Connector terminal 1 to ECM/test box socket 13
Connector terminal 2 to ECM/test box socket 12
Specified value: max. 1.5
Pa
ge 95 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-74

- Check wiring for short circuits between terminals
of 3-pin connector, and between connector and
ECM/test box.


Connector terminal 1 to ECM/test box
socket 12

Specified value:

- Switch multimeter to 20 VDC measuring
range.

- Check wiring at 3-pin connector for short circuit
to B+ (battery positive voltage), according to
applicable wiring diagram.


Connector terminal 1 to vehicle Ground

Connector terminal 2 to vehicle Ground

Specified value: 0 volts
If wiring is OK:

- Replace Mass Air Flow sensor (MAF) -G70-.

-
Check readiness code page 01
-70
. If
Pa
ge 96 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

Diagnostic Trouble Code (DTC) memory has
been erased, or ECM was disconnected,
generate new readiness code page 01
-73
.
Pa
ge 97 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-75

Engine Coolant Temperature (ECT)
sensor, checking


Required special tools and test equipment

VAG1551 or VAG1552 Scan Tool (ST) with
VAG1551/3 adapter cable
VAG1598/22 test box
Multimeter US1119 (Fluke 83 or equivalent)
VW1594 connector test kit
Wiring diagram

Test requirements
Engine cold
Pa
ge 98 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-76

Checking

- Connect VAG1551 or VAG1552 scan tool and
press buttons -0- and -1- to insert "Engine
Electronics" address word 01 (with ignition
switched on) page 01
-8 .
Rapid data transfer
HELP
Select function XX

Indicated on display
- Press buttons -0- and -8- to select "Read Measuring Value Block"
function 08, and press -Q- button to confirm input.
Read Measurin
g Value Block
HELP
Input displa
y group number XXX

Indicated on display
- Press buttons -0-, -0- and -4- to input display group number 4 (004),
and press -Q- button to confirm input.
Read Measuring Value Block 4 1 2 3 4

Indicated on display (1-4 = display fields)
Pa
ge 99 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-77

- Compare display with specified value for engine
coolant temperature sensor (display field 3):

Display fields

1 2 3 4
Display group 4: General engine data
Display xxx RPM xx.xxx V
xxx.x C
xxx.x C
Indicates Engine
speed
(in 40 RPM
steps) Battery Positive
Voltage (B+) Engine coolant temperature Intake air
temperature
Range 0 - 6800
RPM 0.000 - 16.500 V -46.5 to 141.0 -46.5 to 141.0
Specified
value 0 RPM 10.000 - 14.500 V approx. ambient temperature 1), 2) ---

--- --- If specified value is not attained page 24
-79
,
Evaluation of display group 4
---
1) After a long standing period (approx. 12 hours). 2) If indicated temperature deviates significantly from the ambient temperature, check ECT sensor wiring for resistance or
open circuits.
Pa
ge 100 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1