fuse AUDI A6 1998 C5 / 2.G 01V Transmission Electrical Testing Workshop Manual

01-275

The contact numbers of the connector and the
socket numbers of VAG 1598/20 test box match
up page 01
-277
.

To check the multi-function switch, it is not
necessary to connect test box VAG 1598/20
because first the connectors for the multi-
function switch are checked.

CAUTION!

To avoid permanent damage of electronic
components, select the appropriate
measuring range on tester before connecting
the measuring leads.

Test requirements
Battery voltage OK
Fuses for Transmission Control Module
(TCM) OK

Electrical Wiring Diagrams, Troubleshooting &
Component Locations

Fuses for component being tested OK. The
fuse holder is behind a cover on the side of
Pa
ge 4 of 66 Electrical testin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.16

01-277
88-pin connector for Transmission Control Module (TCM) -J217- (sockets on VAG1598/20)
1- Solenoid valve 5 -N92- 18-
Kick-down switch -F8- (not for E-gas and V6-TDI)
2- Shift lock solenoid -N110- 19-
Control input to transmission from ABS control module
3- Vacant 20-
Engine intervention (via ignition timing)
1)
4- Solenoid valve 7 -N94- 21-
ATF temperature sensor -G93-
5- Solenoid valve 4 -N91- 22-
ATF temperature sensor -G93-
6- Ground (GND) for power consumers, term.
31 23-
Sensor for transmission RPM -G182- (shielding)
7- Vacant 24-
Vacant
8- Multi-function TR switch -F125-, L2 25-
Selector lever display (not for Highline combi)
9- Multi-function TR switch -F125-, L4
supply voltage for cruise control system 26-
Supply voltage (terminal 30) with or without fuses depending on
model wiring diagram
10-
Brake light switch -F- (not for E-gas and
V6-TDI) 27-
Kick-down for air conditioning
1)
11-
Vacant 28-
Ground (GND) for electronics (terminal 31)
4)
12- Vacant 29- Solenoid valve 6 -N93-
Pa
ge 7 of 66 Electrical testin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.16

01-283

Voltage measurement: switch multimeter to 20 V measuring range
Test step
VAG
1598/20
sockets Test of
Test conditions
- Additional stepsSpecified
value Corrective action
3
1)
10 + 6
10 +
28
2) Brake light switch
-F-
Ignition switched
on Brake pedal not
depressed less than 1 V
- Check wiring per wiring
diagram.
- Replace and adjust brake
light switch -F-.
not for E-gas
engines
- Brake pedal
depressed approx. battery
voltage Repair Manual, Brake
System, Repair Group 47

4 9 + 6
9 + 28
2) Supply voltage for
Cruise Control, Control
Module
-J213-
Ignition switched
on Selector lever in
D, 4 and 3 approx. battery
voltage - Check wiring from terminals
6 and 28 to Ground.
- Check wiring from terminal 9
to terminal 15 of central
electrics.
- Check wiring to cruise
control, control module -J213-
- Check multi-function switch -
F125- page 01
-322


Selector lever in
P, R, N, and 2 less than 5 V
- Check fuse 31
Pa
ge 16 of 66 Electrical testin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.16

01-312

- If the specified value is not read, check fuses
and wiring connectors according to wiring
diagram and make necessary repairs.

Note:
If the check results and the voltage supply to the
Multi-function TR switch were OK, check wiring
connections from Transmission Control Module
(TCM) -J217- to Multi-function Transmission
Range (TR) switch page 01
-316

Pa
ge 61 of 66 Electrical testin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.16

01-314
Transmission with Multi-function Transmission Range (TR) switch -F125- with 8 - pin connector, checking
Voltage measurement: switch multimeter to 20 V measuring range
Test
step VAG
1598/20
sockets Test of
Test conditions
- Additional stepsSpecified
value Corrective action
1 36 + 34
36 + 6 Multi-function Transmission
Range (TR) switch -F125- Ignition switched
on
- Selector lever in P,
N, and D Approx. 12
V - Check connector at multi-function
switch for corrosion
- Check wiring per wiring diagram

- Selector lever in R,
4, 3, and 2 Less than 1
V - Check fuses
- Check voltage supply to -F125-
page 01
-311
.

8 + 34
8 + 6
Ignition switched
on
- Selector lever in R,
N, and 4 Approx. 12
V - Check wiring from 88-pin control
module to 8-pin connector page
01
-319
.


- Selector lever in P,
D, 3, and 2 Less than 1
V

37 + 34
37 + 6
- Selector lever in N,
D, 4, and 2 Approx. 12
V
Pa
ge 63 of 66 Electrical testin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.16

01-315
Transmission with Multi-function Transmission Range (TR) switch -F125- with 8 - pin connector, checking
Resistance measurement: switch multimeter to 2 M measuring range
Test
step VAG
1598/20
sockets Test of
Test conditions
- Additional stepsSpecified
value Corrective action
2 36 + 8
Multi-function Transmission
Range (TR) switch -F125 Ignition switched
off
- Selector lever in Nless than 26

- Check connector at multi-function
switch for corrosion

- Selector lever in P,
R, D, 4, 3, and 2 infinitive
1)
- Check wiring from 88-pin control
module to 8-pin connector page 01
-319
.

37 + 9

Ignition switched
off
- Selector lever in D
and 4 less than 26

- Perform test steps 6 and 27.


- Fuse 31 removed
2)
- Selector lever in P,
R, N, 3 and 2 infinitive
1)

37 + 36

Ignition switched
off less than 26

Pa
ge 65 of 66 Electrical testin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.16