AUDI A6 2000 C5 / 2.G 01E Transmission Final Drive Flange Housing Remove And Install Workshop Manual

39-81


Drive flange housing, removing
and installing Assembly overview

1 -
Bolt, 40 Nm
2 -
Front cross member
3 -
Bolt, 40 Nm
4 -
Final drive support
5 -
Drive flange housing
6 -
Rear final drive housing
7 -
O-ring
8 -
Bolt, 35 Nm
9 -
Bolt, 23 Nm
10 -
Bracket
For exhaust system
Pa
ge 1 of 7 Drive flan
ge housin
g, removin
g and installin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM03.39.11

39-82

Removing

Rear final drive installed

Special tools, testers and auxiliary items
Multipurpose tool VW 771 and 771/15
Drip tray V.A.G 1306
Universal support V.A.G 1359/2
Engine/transmission jack V.A.G 1383 A

- Place drip tray V.A.G 1306 underneath and
drain transmission oil.

- Remove rear section of exhaust system
(rearward of exhaust pipe clamp(s)):

Repair Manual, 2.7 Liter V6 5V BiTurbo
Engine Mechanical, Engine Code(s): APB, Repair Group 26

Pa
ge 2 of 7 Drive flan
ge housin
g, removin
g and installin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM03.39.11

39-83

- Remove heat shield above driveshaft.

- Remove heat shield next to rear final drive.

- Check whether there is a factory marking (paint spot) on driveshaft. If
not, mark position of driveshaft flange -A- in relation to rear final drive
(arrow -B-) with paint.
- Unscrew bolts from driveshaft flange.

Note:
If it is not possible to push the driveshaft up and off the flange, lower the
final drive before tying up the driveshaft. When lowering the final drive,
prevent the driveshaft from dropping down, and do not bend the center
joint further than the maximum angle permitted Page 39
-64
, Notes. - Secure driveshaft to parking brake cable bracket with wire.
Pa
ge 3 of 7 Drive flan
ge housin
g, removin
g and installin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM03.39.11

39-84

- Support final drive with transmission jack V.A.G
1383 A.

- Unscrew bolts (arrows) on front cross member for rear final drive.
- Detach front cross member.
- Lower final drive about 10 cm.

Note:
Fourth bolt not shown in illustration. - Unscrew 4 bolts for drive flange housing (see -1-, -2- and -3- in
illustration).
Pa
ge 4 of 7 Drive flan
ge housin
g, removin
g and installin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM03.39.11

39-85


- Pull off drive flange with drive flange housing.
Pa
ge 5 of 7 Drive flan
ge housin
g, removin
g and installin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM03.39.11

39-86

Installing
Installation is carried out in the reverse order;
when doing this note the following:

Note:

After removing the driveshaft, it is important to
clean any remaining locking compound out of
the threads in the drive flanges on the
transmission and rear final drive. If this is
neglected, the new bolts can seize when they
are screwed in and shear off later if they have
to be removed.
The threaded holes can be cleaned with a
thread tap.
Replace gasket between driveshaft and drive
flange (pull off backing foil and stick gasket onto
drive flange). Surface must be free of grease.
Replace driveshaft bolts (self-locking).

- If there is a factory marking on the driveshaft,
measure the radial run-out at the flange for the
driveshaft ( Page 39
-73
) and align the paint
marking on the driveshaft with new marking on
the flange.
Pa
ge 6 of 7 Drive flan
ge housin
g, removin
g and installin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM03.39.11

39-87

- Align exhaust system free of stress.

Repair Manual, 2.7 Liter V6 5V
BiTurbo
Engine Mechanical, Engine Code(s): APB, Repair Group 26


- Top up gear oil in rear final drive and check oil
level Page 39
-80
.

Tightening torques

Component
Nm
Drive flange housing to rear final drive 35
Driveshaft to final drive
(input flange) 55
Front cross member for rear final drive to
body 40
Front cross member for rear final drive and
exhaust bracket to body 23
Oil filler plug 35
Nuts for clamp 40
Pa
ge 7 of 7 Drive flan
ge housin
g, removin
g and installin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM03.39.11