warning AUDI A6 2008 C6 / 3.G Infotainment MMI Operating Manual

Using the telephone87
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control
Using the telephone
Applies to vehicles: with Bluetooth car telephone kit or phone pre-installation
Introduction
You can operate a mobile phone* or the handset conveniently via
the MMI system. It does not matter whether the mobile phone is
connected to the Bluetooth car telephone kit or the phone pre-
installation. The basic operation via the MMI control console is
always the same.
Many telephone functions that you are familiar with from your land
line or your mobile phone are available in your vehicle: You can
answer and end calls, place calls on hold and go back and forth
between two separate calls (switching calls). In addition, you can
access the MMI directory, the phone book on your SIM card and the
phone book on your mobile phone.
When you place or receive telephone calls the audio source is
muted automatically and the current media drive is paused. A
crossed-out loudspeaker will appear in the display when the system
is muted. After the call the audio source will return to its previous
volume.
You can set the system so that it will switch off the navigation* voice
guidance during phone calls if desired
page 119.
Caution
•You must switch off the telephone system via the MMI menu
(Setup Telephone) in areas where the use of mobile telephones is
prohibited. Please observe all relevant caution notices and regula-
tions.
•Switch off the car telephone kit, the handset*
page 140 and
any other mobile phones in all areas where there may be a risk of
explosion. Remember that these areas may not always be
adequately marked. Such places are filling stations, fuel and chem-
ical storage facilities or transport vehicles and other places where fumes, chemicals (e.g. from leaking propane or fuel vapours in vehi-
cles or buildings) or large quantities of dust particles (e.g. from
flour, wood or metal) could accumulate in the air. This warning also
applies to all other places where you would normally switch off your
engine.
Note
The telephone functions will depend on the mobile network service
provider and the mobile phone used. For more information, contact
your service provider.
Applies to vehicles: with Bluetooth car telephone kit or phone pre-installation
Requirements for using the
telephone
If you want to use the telephone function of your MMI system, one
of the following requirements must be met:
•A mobile phone must be connected to the Bluetooth car tele-
phone kit
page 24, or
•A handset* must be connected to the Bluetooth car telephone kit

page 27, or
•A mobile phone must be connected to the phone pre-installation

page 19.
In vehicles fitted with a Bluetooth car telephone kit, the car tele-
phone must be switched on
page 26.










Using the telephone 90
WARNING
Since your telephone operates via radio waves, a connection
cannot be guaranteed under all circumstances. Do not rely solely
on your telephone when a vital communication (e.g. medical emer-
gency) is involved.
Note
You can also place an emergency call using the handset*

page 147.
Dialling a telephone number
Applies to vehicles: with Bluetooth car telephone kit or phone pre-installation
Directly via the speller
Using the speller, you can enter a telephone number
directly (as a series of numbers or as a series of letters).
Important: The telephone mode must be activated

page 26, and the speller must be displayed on the MMI
display
fig. 83.
Entering a telephone number using numbers
– Enter the telephone number via the speller.
– To confirm your entry turn the speller to OK and press the
rotary pushbutton, or
– Press the control button for Dial. After the connection
has been established, the audio system will be muted.
Entering a telephone number using letters
– Enter a code, e.g. 0800 via the speller
fig. 83.
– To switch to the speller for letters, turn the speller to A-Z

fig. 83 and press the rotary pushbutton. The speller
for letters will appear on the MMI display
fig. 84.
– Enter a series of letters, e.g. AUDISERVICE via the speller

fig. 84.
– To confirm your entry turn the speller to OK and press the
rotary pushbutton, or
Fig. 83 Entering a tele-
phone number via the
speller for numbers
Fig. 84 Entering a tele-
phone number via the
speller for letters
A1










Navigation 104
Navigation
Applies to vehicles: with navigation system
Introduction
Let the “Global Positioning System” (GPS) guide you to
your destination.
Wasting time studying confusing maps and tediously planning
routes are things of the past! Now you can simply enter your desired
destination into the navigation system, and the route guidance will
guide you directly to it. You can also set up to three stopovers on the
way to your destination.
The route guidance will be transmitted in the form of spoken cues
that will inform you in good time of any necessary turns, stops etc.
In which language would you like to hear the route guidance? You
can select any of the following languages: German, English, French,
Italian, Portuguese, Spanish or Dutch. You can have the last route
guidance cue repeated by pressing the right-side thumbwheel on
the multi-function steering wheel
page 137.
A detailed route map is displayed on the MMI screen
page 110.
You can also receive information on your route via the driver infor-
mation system
page 111.
If you do not want to follow a certain route guidance cue, no
problem! The navigation system will re-calculate the route from the
current location of the vehicle. In addition, if the dynamic navigation
function is activated, the navigation system will even take into
account traffic reports so that you can reach your destination even
faster.
If the vehicle is located in a place that cannot be identified by the
software (e.g. car park), a speech cue will inform you of this.
WARNING
•Today's driving conditions require the full attention of drivers.
Please see
page 9, “Notes on traffic safety”.
•Pay attention to traffic rules when driving.
•The route calculated by the navigation system is a recommen-
dation of how best to reach a destination. Pay attention to traffic
lights, no stopping signs, lane change restrictions, one-way
streets, etc.
Caution
•Should the navigation directions contradict the current traffic
regulations, you must always follow the traffic regulations.
•The volume should only be set at a level which enables you to
hear distant police and emergency vehicles clearly - failure to do so
could result in an accident.
Note
•Snow or other obstructions on the GPS aerial or interference
caused by trees or large buildings could affect the reception of the
satellite signals and make positioning difficult. GPS reception and
vehicle positioning can also be adversely affected by deactivation or
a malfunction of several satellites.
•Street and town names can change, therefore the names stored
on the DVD can in some cases be different from the names that have
since been changed.
•The navigation DVDs can only be purchased from Audi dealers.
They can also provide you with information on the most recently
updated navigation DVDs.










Navigation 112
After you have entered a destination or a route and have started the
route guidance, the navigation information is displayed in the driver
information system. If you select another function (e.g. radio) using
the multi-function steering wheel, the navigation will briefly be
replaced by the function selected
page 128.
Distance to turn-off
Estimated time of arrival
Total distance to destination/next stopover
Name of motorway, major road or street you are driving on. An
arrow in front of the street name indicates that you are
supposed to turn into the street.
Arrow indicating a turn-off. A necessary lane change before the
turn is also displayed.
Bar graph. If an arrow is displayed, a bar graph will also appear.
The fewer bars are displayed, the shorter the distance to the
turn-off point.
WARNING
The route calculated by the navigation system is a recommenda-
tion of how best to reach a destination. Pay attention to traffic
lights, no stopping signs, lane change restrictions, one-way
streets, etc.
Note
An exclamation mark “!” in front of the street name indicates that
the navigation DVD does not contain all the information on this
street or street section. Pay attention to traffic rules such as one-way
streets or pedestrian zones.
Storing a destination
Applies to vehicles: with navigation system
In the directory (single destination)
A single destination can either be stored as a new entry or
added to an existing entry.
Important: You must have entered a single destination

page 107.
Storing a destination as a new entry
– Press the Memory control button.
– Turn the rotary pushbutton to Store in directory and
press to confirm.
– Turn the rotary pushbutton and select New entry.
– Press the rotary pushbutton. An entry space will now
appear
fig. 103.
– Turn the rotary pushbutton to Surname and press the
rotary pushbutton. The speller will appear on the MMI
display
page 43.
– Enter the surname using the speller.
A1
A2
A3
A4
A5
A6
Fig. 103 Address card











Calling up traffic information123
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control
Important: The system must be tuned to a traffic station

page 122, and a navigation DVD must be inserted in the
drive
page 14.
– Press the function selector button marked .
– If the list of traffic messages
page 122, fig. 108 does
not appear in the MMI display, press the function
selector button again. A list of traffic messages

page 122, fig. 108 will now appear in the MMI display.
– Turn the rotary pushbutton to mark an entry.
– Press the rotary pushbutton. Traffic information on the
entry will now be displayed.
– To display the next traffic message in the detail view, turn
the rotary pushbutton to Display next report and press to
confirm.
– To display the selected message on the map in the detail
view, turn the rotary pushbutton to Show report on map.
– Press the rotary pushbutton. The red hatched line shows
the stretch of road affected by the traffic obstruction

fig. 109.– To display the next traffic message on the map, press the
rotary pushbutton again.
When the route guidance is active, the TMC traffic messages which
are relevant for your route are shown with a red warning symbol and
are sorted by distance to your current location
page 122,
fig. 108. A traffic obstruction in the immediate vicinity will be shown
at the top of the list.
All other traffic messages are then shown with greyed-out warning
symbols and are sorted according to road category (motorways,
major roads, other roads) and road number.
Urgent traffic messages such as a car travelling in the wrong direc-
tion on the motorway are automatically displayed in the MMI
display. To cancel the report, simply press the button or
the rotary pushbutton.
When the route guidance is active, traffic messages are shown with
red warning symbols and are sorted according to road category
(motorways, major roads, other roads) and road number.
Other settings
Applies to vehicles: with TP memo timer
TP memo timer
– Select: Function selector button > function
selector button > TP memo timer.
You can set two times of day at which you want the MMI system to
record traffic reports. Use the Timer status option to activate and
deactivate the timers individually or together. You can set the time
by turning the rotary pushbutton to mark the timer and pressing to
confirm. Then turn the rotary pushbutton to change the time.
Switch from hours to minutes by pressing the rotary pushbutton.
Fig. 109 Displaying a
TMC traffic message
on the map
INFO
INFO
A1
RETURN
INFO
SETUP











Using the telephone 148
– When the message Do you really wish to connect to the
emergency number? appears in the handset display,
confirm with Ye s. The emergency number will be dialled.
With SIM card and PIN entered
– Switch on the ignition, the MMI and (if not already acti-
vated) the handset
page 140. A Bluetooth connection
must exist between the handset and the car telephone
kit, and a SIM card must be in the handset.
– If necessary, press the “End call” button to display the
main screen
page 142, fig. 126.
– Enter the emergency number (e.g. 112).
– Press the “Call” button
page 140, fig. 124 to start
dialling.
WARNING
Since your telephone operates via radio waves, a connection
cannot be guaranteed under all circumstances. Do not rely solely
on your telephone when a vital communication (e.g. medical emer-
gency) is involved.
Note
•You can also dial an emergency number on the MMI
page 89.
•Always follow the directions of the emergency operators when
making an emergency call. Do not end the call before you are
requested to do so. Otherwise, this could result in life-saving infor-
mation not being passed on.
•Emergency numbers are not the same for all countries. Please
familiarise yourself with the correct emergency numbers in advance
when travelling in foreign countries or regions where the numbers
may be different.
Applies to vehicles: with handset for the car telephone kit
Ending calls
– To end an active call or stop dialling a number, press the
control button for End call
fig. 133, or
– Press the “End call” button
page 140, fig. 124.
If you placed a call on hold earlier on, that call will remain on hold.
Use the Resume function to continue the call.
If a menu is open in the handset display, the menu will be closed the
first time you press the “End call” button. The active call is discon-
nected when you press the “End call” button again.
A7
Fig. 133 Active call
A3










Telephone speech control system 160
Telephone speech control system
Applies to vehicles: with telephone speech control system
Introduction
You can use speech commands to operate various func-
tions of the telephone.
Functions
The speech control and hands-free system together enable you to
operate the on-board phone system very conveniently. The speech
control system recognises commands and digits spoken by
different people.
The speech control system allows you to do the following:
•Store name tags
page 164
•Enter and dial a telephone number
page 163
Traffic reports are not announced during a running dialogue. The
dialogue will be ended immediately when an incoming phone call is
received.
Unrecognised speech commands
The system acknowledges your commands with a tone signal. If the
system does not recognise a speech command, it will answer with
<Pardon?> and request you to repeat the command. After a third
failed attempt the system will answer with <Cancel> and the
dialogue will be ended.
How to help the system understand you
•Speak clearly in a normal volume. Speak louder if you are driving
fast.
•Speak in a normal tone without long pauses.
•Avoid speaking when the system is saying a cue.
•Close doors, windows and sun roof* to reduce background
noise. Make sure that passengers are not talking when you say a
command.
•Keep the air outlets of the air distribution system pointed away
from the microphone, which is fitted in the vicinity of the front inte-
rior lights.
•The system should only be operated by the driver, since the
hands-free microphone is directed towards the driver.
<The function is not possible>
Should the system say <The function is not possible>, please check
the status of the speech control system:
•Is the MMI active and the ignition on?
•Does a Bluetooth connection exist between the mobile phone
and the on-board phone system (car telephone kit* or phone pre-
installation*)?
•Is the mobile phone inserted in the mobile phone adapter*25)?
•Is the mobile phone switched on and the PIN entered?
•Are the phone book entries being loaded from the mobile phone
into the on-board phone system (car telephone kit*
page 29 or
phone pre-installation*
page 23)?
WARNING
•Please direct your full attention to the road at all times! As the
driver, you have full responsibility for the safety of the vehicle and
other road users. For this reason, you should only use the func-
tions in a manner that allows you to maintain control of the
vehicle in all situations - accident risk!
•The speech control system must not be used in cases of emer-
gency, since the voice changes in stressful situations. This could
result in a failed or delayed telephone connection. Always dial
emergency numbers manually!
25)Applies to phone pre-installation.





!




Speech dialogue system169
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control
Speech dialogue system
Applies to vehicles: with multi-function steering wheel and speech dialogue system
Introduction
You can operate many functions of the MMI quickly and
easily with the speech dialogue system.
Using the speech dialogue system you can conveniently switch
between the various modes, e.g. from radio to CD mode. You can
also access various functions on the radio, the CD changer, the tele-
phone* or the directory by saying commands or calling up previ-
ously stored name tags
page 172. In addition, you can select navi-
gation* destinations and have the system guide you to them, call up
the map display and change the map scale
page 178.
If you do not know a command, no problem! If the speech dialogue
system is activated, simply say HELP. The system will transmit the
commands you can currently say or will help you with a cue

page 171.
The speech dialogue system recognises commands and spoken
numbers regardless of the speaker.
How to help the system understand you
•Speak clearly in a normal volume. Speak louder if you are driving
fast.
•Speak in a normal tone without long pauses.
•Avoid talking while the speech dialogue system is giving a cue.
•Close doors, windows and sun roof* to reduce background
noise. Make sure that passengers are not talking when you say a
command.
•Keep the air outlets of the air distribution system pointed away
from the microphone, which is fitted in the vicinity of the front inte-
rior lights.
•The system should only be operated by the driver, since the
hands-free microphone is directed towards the driver.Unrecognised speech commands
The system acknowledges your commands with a tone signal. If the
system does not recognise a speech command, it will answer with
<Pardon?> and request you to repeat the command. After a third
failed attempt the system will answer with <Cancel> and the
dialogue will be ended.
WARNING
•Please direct your full attention to the road at all times! As the
driver, you have full responsibility for the safety of the vehicle and
other road users. For this reason, you should only use the func-
tions in a manner that allows you to maintain control of the
vehicle in all situations - accident risk!
•The speech control system must not be used in cases of emer-
gency, since the voice changes in stressful situations. This could
result in a failed or delayed telephone connection. Always dial
emergency numbers manually!





!