warning AUDI A6 2017 Owners Manual

co
co
.... N
" N .... 0 0 <..:l '<t
should always ride in the back seat properly restrained for their age and size.
A WARNING
Improperly installed child safety seats in­
crease the risk of serious personal injury and
death in a collision.
-Always make sure that the safety belt re­ tractor is locked when installing a child safety seat. An unlocked safety belt retrac­
tor cannot hold the child safety seat in place
dur ing normal driving or in a crash .
- Always buckle the child safety seat firmly in
place even if a child is not sitting in it . A
loose child safety seat can fly around during
a sudden stop or in a collision.
- Always make sure that the rear seat back­
rest to wh ich the center rea r safety be lt* is
attached is secure ly latched whenever the
rear cente r safety belt is being used to se­
cure a chi ld restraint.
- If the backrest is not securely latched, the
child and the child restraint will be thrown
forward together with the backrest and will
strike parts of the vehicle interior . The chi ld
can be seriously injured or killed.
- Never install rear-facing chi ld safety seats
or infant carriers on the front passenger
seat. A child will be serious ly injured and
can be killed when the passenger airbag in­
flates.
- The inflating a irbag w ill hit the child safety
seat or infant carrier with great force and
will smash the ch ild safety seat and child
against the backrest, center armrest, door
or roof.
- Always install rear -facing child safety seats
or infant carriers on the rear seat.
- Forward -facing ch ild safety seats or infant
carriers installed on the front passenger 's
seat may inte rfere with the deployment of
the a irbag and cause serious injury to the
child.
- It is safer to install a forward-fac ing ch ild
safety seat on the rear seat.
- Always read and heed all WARNINGS when­
ever using a child restrained in a veh icle is
being used
r:::> page 171 . Specia l precaut ions
Ch ild safety
apply when install ing a child safety seat on
the front passenger seat
r:::> page 148, Child
restraints on the front seat -some impor­
tant things to know .
A WARNING
Always take special precautions if you must
i nstall a forward or rearward-facing child re­
stra int on the front passenger's seat in excep­
tional s ituations:
- Whenever a forward or rearward-fac ing
child restraint is installed on the front pas­
senger seat, the
PASSENGER AIR BAG OFF
light must come on and stay on whenever
the ignition is switched on .
- I f the
PASSENGER AIR BAG OFF light does
not come on and stay on, perform the
checks described
r:::> poge 159, Monitoring
the Advanced Airbag System.
- Take the child restraint off the front passen ­
ger seat and install it properly at one of the rear seat positions if the
PAS SENGER AIR
BAG O FF
light does not stay on whenever
the ignition is switched on.
-Improper installat ion of child restraints can
reduce the ir effectiveness or even prevent
them from providing any protect ion.
- An improperly installed child restra int can
interfere with the airbag as it deploys and
serious ly injure or even kill the child.
- Always carefully follow the manufacturer's
instructions provided with the child safety
seat or carr ier.
- After checking to make sure that the child
restraint is properly installed, make certain
that the child restraint is correctly recog ­
n ized by the capacitive passenge r detection
system in the front passenger seat and that
the
PASSENGER AIR BAG OFF light signals
the correct front passenger frontal airbag
stat us.
A WARNING
Forwa rd -facing child restraints :
-
183

Child safety
-Always make sure the forward-facing seat
has been designed and certified by its man­
ufacturer for use on a front seat with a
passenger front and side airbag.
- Never put the forward-facing child restraint
up, against or very near the instrument pan­
el.
- Always move the front passenger seat to
the highest position in the up and down ad­
justment range and move it back to the
rearmost position in the seat's fore and aft
adjustment range, as far away from the air­
bag as possible, before installing the for­
ward-facing child restraint.
- Always make sure that the safety belt upper
anchorage is behind the child restraint and
not next to or in front of the child restraint
so that the safety belt will be properly posi­
tioned.
- Make sure that the
PASSENGER AIR BAG
OFF
light comes on and stays on all the time
whenever the ignition is switched on.
A WARNING
Rearward-facing child restraints:
- A child in a rearward-facing child safety seat
installed on the front passenger seat will be
seriously injured and can be killed if the
front airbag inflates -even with an Ad­
vanced Airbag System.
- The inflating airbag will hit the child safety seat or infant carrier with great force and
will smash the child safety seat and child against the backrest, center armrest, door
or roof.
-Always be especially careful if you must in­
stall a rearward facing child safety seat on
the front passenger seat in exceptional cir­
cumstances.
- Make sure that the
PASSENGER AIR BAG
OFF
light comes on and stays on all the time
whenever the ignition is switched on.
- If the
PASSENGER AIR BAG OFF light does
not come on and stay on, immediately in­
stall the rear-facing child safety seat in a
rear seating position and have the airbag
system inspected by your Audi dealer.
184 ·
Activating the convertible locking retractor
Use the convertible locking retractor to secure a
child restraint.
Always heed the child safety seat manufacturer's
instructions when installing a child restraint in
your vehicle. To activate the convertible locking retractor:
.. Place the child restraint on a seat, preferably
on the rear seat.
.. Slowly pull the belt
all the way out.
.. Route it around or through the child restraint
belt path
~ ,&. .
.. Push the child safety seat down with your full
weight to get the safety belt really tight.
.. Insert the belt tongue into the buckle for that
seating position.
.. Guide the safety belt back into the retractor un­
til the belt lies flat and snug on the child safety
seat.
.. You should hear a "clicking" noise as the belt
winds back into the inertia reel. Test the con ­
vertible locking retractor by pulling on the belt.
You should no longer be able to pull the belt
out of the retractor. The convertible locking re­
tractor is now activated.
.. Make sure that the red release button is facing
away from the child restraint so that it can be
unbuckled quickly.
.. Pull on the belt to make sure the safety belt is
properly tight and fastened so that the seat
cannot move forward or sideways more than
one inch (2 .5 cm) .
A WARNING
Using the wrong child restraint or an improp­
erly installed child restraint can cause serious
personal injury or death in a crash.
- Always make sure that the safety belt re­
tractor is locked when installing a child
safety seat. An unlocked safety belt retrac­
tor cannot hold the child safety seat in place
during normal driving or in a crash.
- Always buckle the child safety seat firmly in
place even if a child is not sitting in it. A
loose child safety seat can fly around during
a sudden stop or in a crash.
IIJJ,-

co
co
.... N
" N .... 0 0 <..:l '<t
-Always make sure the seat backrest to which
the child restraint is installed is in an up­
right position and securely latched into
place and cannot fold forward. Otherwise,
the seatback with the child safety seat at­
tached to it could f ly forward in the event of
an accident or other emergency situation.
- Always read and heed all WARNINGS when­
ever using a child restrained in a veh icle is
being used¢
page 171. Specia l precaut ions
apply when installing a child safety seat on
the front passenger seat¢
page 148, Child
restraints on the front seat -some impor­
tant things to know.
Deactivating the convertible locking
retractor
The convertible locking retractor for child re­
straints will be deactivated automatically when
the belt is wound all the way back into the re­
tractor .
~ Press the red button on the safety belt buckle.
The belt tongue will pop out of the buckle.
~ Guide the safety belt all the way back into its
stowed position .
Always let the safety belt retract completely into
its stowed position. The safety belt can now be
used as an ordinary safety belt without the con­
vertible locking retractor for child restraints.
If the convertible locking retractor should be ac­
tivated inadvertently, the safety belt must be un­
fastened and guided completely back into its
stowed position to deact ivate this feature. If the
convert ible locking retractor is not deactivated,
the safety belt w ill gradually become tighter and
uncomfortable to wear.
_& WARNING
-
Improperly installed chi ld safety seats in­
crease the risk of serious personal injury and
death in a collision.
- Never unfasten the safety belt to deactivate
the convertible locking retractor for child re­
straints while the vehicle is moving . You
Child safety
would not be restrained and could be seri­
ously injured in an accident.
- Always read and heed all WARNINGS when­
ever using a child restrained in a vehicle is
be ing used
¢page 171. Special precautions
apply when install ing a child safety seat on
the front passenger seat¢
page 148, Child
restraints on the front seat -some impor­
tant things to know.
LATCH system (lower
anchorages and tethers
for children)
Child Restraint System anchors and how
are they related to child safety
To provide a simpler and more practicab le way to
attach the child restraint on the vehicle seat,
Federal regulations require special lower ancho­
rages in vehicles and devices on new child re­
straints to attach to the vehicle anchorages .
In the United States, the combination of the
tether anchorages and the lower anchorages is
now generally called the LATCH system for
"Lower Anchorages and Tethers for Children". In
Canada, the terms "top tether" with "lower uni­
versa l anchorages" (or "lower universal anchor­
age bars") are used to descr ibe the system .
In other countries the term "ISOFIX" is used to
describe the lower anchorages .
Forward-facing child restraints manufactured af­
ter September 1, 1999 , are required by U.S. fed­
eral regulations to comply with new child head
movement performance req uirements. These
new performance requirements make a tether
necessary on most new ch ild seats.
Installing a child restraint that requires a top
tethe r without one can seriously impair the per­
formance of the child restraint and its ab ility to
protect the child in a collision. Installing a child
restra int that requi res a top tether without the
top tether may be a violation of state law.
Child restraint manufacturers offer LATCH lower
anchorages on their child seats w ith hook-on or ..,.
185

Child safety
push-on connectors attached to adjustable
straps.
I n addition to the LATCH lower anchorages, these
chi ld restraint systems usually require the use of
tether straps to he lp keep the child restraint
firm ly in place.
A WARNING
Improper installation of child restraints will
increase the risk of injury and death in a
crash.
- Always follow the instructions provided by
the manufacturer of the child restraint you intend to install in your veh icle.
- Never install a child restraint without a properly attached top tether strap if the
child restraint manufacturer's instruct ions
requ ire the top tether strap to be used.
- Improper use of child restra int LATCH lower
anchorage points can lead to injury in a colli­
s ion . The LATCH lower anchorage points are
designed to withstand on ly those loads im­
posed by cor rect ly fitted child restraints .
- Never mount two child restraint systems on
one LATCH lower anchorage point.
- Never secure or attach any luggage or other
item to the LATCH lower anchorages.
Location
Fig. 168 Schematic overview : LA TCH anchorage point loca­
t ions
The illustration shows the seating locatio ns in
your veh icle which are equipped with the lower
anchorages system.
186
Description
The lower anchorage positions are marked for
quick locating .
Fig. 169 Lower anchorages, covers marked
Fig . 170 Rear seats: lower anchorage bracket locat ions
L o wer anch ora g es
The circular markings on the rear seat help you to
identify the location of lower anc horages for the
two outboard seating positions
¢fig . 169. The
LATCH lower universal anchorage attachment
points are between the rear seatback and rear
seat cushion .
Remove the covers
¢ fig . 169 to access the lower
anchorage attachment points.
The lower ancho rage attac hment po ints are vis i­
ble
¢ fig. 170.
Lower anchorages secure the child restra int in
the seat wi thou t usi ng the vehicle's safety belts.
Anchorages p rov ide a secure and easy-to-use at ­
tachment and minimize the possibility o f improp­
er child restraint installation.
All child restra ints manufact ured after Septem­
ber 1, 2002, must have lower anchorage attach-
ments for the
LATCH system. ..,.

co
co
.... N
" N .... 0 0 <..:l '<t
Please remember that the lower anchorage
points are only intended for installation and at­
tachment of child restraints specifically cert ified
for use with
LATCH lower anchorages. Child re­
straints that are not equipped with the lower an­
chorage attachments can still be installed in
compliance w ith the child restra int manufactur­
er 's instructions on using vehicle safety belts .
.8, WARNING
Improper use of LATCH lower anchorages can
cause serious personal injury in an accident.
- Always caref ully follow the child restra ints
man ufactu rer's inst ructions for proper in­
sta llation of the child restr aint and proper
u se of the lower anchorages or safety be lts
in your vehicle.
- Never secure or attach any luggage or other
items to the
LATCH lower anchorages.
- Always read and heed t he important infor­
mation about child restraints in this chapter
and WARNINGS
~ page 171, Child safety .
Installing a child restraint with LATCH
lower anchorages
Whenever you install a child restraint always fol­
low the child restraint manufacturer's instruc­
tions.
F ig . 171 Lower anchorages: proper mount ing
Mounting
.,. Make sure the seatback of the rear seat bench
is in the upr ight position and sec urely latched
i n place .
.. Attach both hook-on connectors with the spring
catch re lease on the ch ild safety seat onto the
Ch ild safety
LATCH lower anchorage so that the connectors
lock into p lace
¢ fig. 171.
.. Pull on the connector attachments to make
sure they are properly attached to the LATCH
lower anchorage.
.. Pull straps tight following the ch ild restraint
manufacturer 's instructions .
Relea sing
.. Loosen the tension on the straps fo llow ing the
child restra int manufacturer's instructions.
.. Depress the spr ing catches to release the an­
chorage hooks from the lower anchorages .
Remember: Use tether straps to help keep the
child restraint firmly in p lace.
.8, WARNING "---Imp roper use of the LATCH system can in­
crease the risk of serious personal injury and
death in an accident.
- These anchors were developed only for child safety seats using the "LATCH" system.
- Never attach other ch ild safety seats, belts
or other objects to these anchors.
- Always make sure that you hear a click when
latching the seat in place. If you do not hear
a click the seat is not sec ure and co uld f ly
forward and hit the inter io r of the vehicle,
or be ejected from the vehicle .
.8, WARNING
I mp roper installation of child restra ints w ill
i n cr ease the risk of inju ry in an a ccident.
- Always follow the ch ild restraint system
manufac ture r's ins tructions fo r prope r in­
s tallat ion of the ch ild restrain t system and
proper use of tether straps as well as the
lower anchorages or safety belts in yo ur ve­
h icle.
- Always read and heed the important infor­
matio n and WARNINGS about ch ild safety
and the installat ion of child restraint sys­
tems
¢ page 171, Child safety .
-
187

Child safety
Tether anchors and tether straps
Fig. 172 Tether anchors: recess flaps behind the rear seat·
backs
The tether anchors fo r the rear seating positions
are located in recesses in the rear window shelf
~ fig. 172
A tether is a stra ight or V-shaped strap tha t at­
taches the top part of a child restra int to speci al
anchorage points in the vehicle.
The purpose of the tether is to red uce the for­
ward movement of the child restraint in a crash,
in order to help red uce the risk of head injury
that could be caused by strik ing the vehicle inte­
rior.
Forward fac ing child restraints manufactured af ­
ter September 1, 1999, are required by U.S. fed­
eral regulations to comply with new child head
movement performance requirements. These
new perfo rmance requirements make a tethe r
necessary on most new child safety seats.
A WARNING
Improper installation of ch ild restraints will
increase the r isk of injury and death in a
crash.
- Always follow the instructions provided by
the manufacturer of the child restra int you
intend to install in your Audi .
- Improper use of child restra int anchors (in­
clud ing tether anchors) can lead to inj ury in
a collision . The ancho rs are designed to
withs tand only those loads imposed by cor­
rectly fitted child restra ints.
- Never mount two chi ld restraint systems on
one LATCH lower a nchor po int.
188
- Never attach two child restraint systems to
one tether strap or tether anchorage.
- Never attach a tether strap to a tie-down
hook in the luggage compartment .
- Never use child restraint tether anchorages
to secure safety be lts or other kinds of occu­
pant restraints.
- Never secure or attach any luggage or othe r
items to the LATCH lower anchorages or to
the tether anchors.
- If you must install a rearward facing child
safety seat on the front passenger seat be­
cause of exceptional circumstances and the
PASSEN GER AIR BAG OFF light does not
come on and stay on, immediately install
the rea r-facing child safety seat in a rear
seating position and have the ai rbag system
inspected by yo ur Audi dea ler.
Installing the upper tether strap on the
anchorage
F ig. 173 Tether strap: p roper rout ing and mount ing
Install ing the tether st rap
.. Release or deploy the tether strap on the ch ild
restraint according to the chi ld restraint manu­
facturer's instructions.
.. Guide the upper tether strap
under the rea r
head restraint ~
fig. 173 (raise the head re­
straint if necessary). For child restraints with V­
tether straps, always make sure that the head
restraint guide rods do not interfere with any
part of the top tether strap.
.. Tilt the recess flap up to expose the anchor
bracket .
., Attach the tether st rap anchorage hook into
the opening of t he tether ancho rage.

co
co
.... N
" N .... 0 0 <..:l -<t
~Pullon the tether strap hook so that the spring
catch of the hook engages.
~ Tighten the tether strap firmly fo llow ing the
child restraint manufacturer's instructions.
Releasing the tether strap
~ Loosen the tension following the child restraint
manufacturer's instructions.
~ Depress the spring catch on the hook and re­
lease it from the anchorage .
(1;) Note
If you leave the chi ld restraint with the tether
strap firmly installed for several days, this
could leave a mark on the upholstery on the
seat cushion and backrest in the area where
the tether strap was installed . The upholstery
would also be permanently stretched around
the tether strap . This applies especially to
leather seats.
Using tether straps on rearward-facing
child restraints
Current ly, few rear-facing chi ld restraint systems
come with a tether. Please read and heed the
child restraint system manufacturer's instruc­
tions carefully to determine how to properly in­
stall the tether .
A WARNING
A child in a rearward-facing child safety seat
installed on the front passenge r seat w ill be
ser iously injured and can be killed if the front
airbag inflates - even w ith an Advanced A irbag
System.
- T he inflating airbag will hit the child safety
seat or infant carrier with great force and
will smash the chi ld safety seat and child
against the backrest, center armrest, or
door.
- If you must install a rearward facing child
safety seat on the front passenger seat be­
cause of exceptiona l circumstances and the
PASSENGER AIR BAG OFF light does not
come on and stay on, immed iately install
the rear-facing child safety seat in a rear
Child safety
seating position and have the airbag system
inspected by your Audi dealer.
Additional information
Sources of information about child
restraints and their use
There are a number of sources of additional in­
formation about child restraint selection, instal­
lation and use :
N HT SA advises that the best ch ild safety seat is
the one that fits your child and fits in your vehi­
cle, and that you wi ll use correct ly and consis ­
tent ly.
T ry before you buy!
U.S National Highway Traffic Safety Administra­
tion
T el. : 1-888 -327-4236 ( TTY: 1-800-424-9153)
http:/ /www.nhtsa.gov
http:/ /www.sa fercar.gov
National SAFE KIDS Campaign
T el.: (202) 662-0600
http:/ /www.safekids .org
Safety BeltSafe U.S.A
Tel.: (800) 745-SAFE (En glish)
T el.: (800) 747-SANO (Spanish)
http:/ /www.carseat.org
Transport Canada Information Centre
T el.: 1-800-333-0371 o r call 1-613-998-8616 if
you are in the Ottawa area
http://www.tc.gc.ca/ eng/roadsafety/menu . htm
Audi Customer Relations
Tel.: (800) 822-2834
189

Checking and Filling
These fuel s contain substances that can se ­
verely damage the fue l system and the en­
gine if the engine is started .
Refueling
Fuel filler neck
The fuel fille r neck is located on the r ight rear
side pane l beh ind the f uel fi ller flap.
If the power locking system should fail , you can
still open the flap manua lly - for deta iled instruc­
tions see~
page 194 .
You can find the fuel tank capac ity of your vehicle
i n
~ page 257 .
The label on the inside of the fuel filler flap tells
you the correc t fuel for your vehicle . For more in­
formation about fue l specifications , see
~ page 190 .
Your veh icle fuel t ank has an onboard refuelling
vapor recovery sys tem . This fea tu re he lps to pre­
vent fuel vapors from escaping from the tank and pollut ing the env ironment while you refuel your
ve hicle. In order to fill the tank prope rly while
p rotecting the environment, please fo llow this
re fueling proce dure caref ully.
8_ WARNING
Under no rmal o perating conditions, never car ­
ry additiona l fuel containers in yo ur car. Gas
canisters and ot her containers used to trans­
port fuel can be dangerous . Such containers,
full or empty, may leak and could cause a fire
in a collision . If yo u must t ransport fue l to
use for yo ur lawn mower, snow blower, etc.,
be
very careful and a lways observe loca l and
s tate laws regar ding t he use, transportation
a nd sto rage of s uch fue l conta iners. Make ce r­
t ain the con tainer mee ts in dust ry sta ndards
(A NSI/AS TM F8S 2 - 86) .
(D Note
Never d rive yo ur vehicle unt il t he fuel tan k is
c ompletely empty . T he irregu lar sup ply of
fue l can ca use m isfiri ng. Gasoline cou ld enter
t he exha ust system and damage the catalytic
converter.
192
Fueling procedure
Fi g. 17 4 R ig ht rea r side o f th e ve hicle: ope ning t he fuel
fi ll er door
Fig . 1 75 Fue l fill er doo r w it h at tac hed fu el cap
The fue l filler doo r is u nlocked or locked by the
central locking system .
Opening the fuel cap
" Press on the left side of the fue l filler door to
open
~ fig . 174.
"Unscrew the tank cap co unterclo ckwise .
" Place the cap from
above on the open f uel f iller
door
~ fig. 175 .
Closing the fuel cap
" Scr ew the tank cap on to the right on the filler
neck unt il it ca nnot turn any fart her .
" Then press on the left s ide of the t an k door un-
til it latches.
Once the pump no zzle switches off , t he fuel ta nk
i s "full ". Do not fill the tank mo re . O therwise the
expans io n sp ace in the tan k w ill be filled.
The co rrect fuel type for your vehicle can be
fo und o n a label located on the inside of the f uel
fille r door . Fo r addi tional informat io n on fuel,
see
~ page 190 .

co
co
.... N
" N .... 0 0 <..:l '<t
The fuel tank capacity of your vehicle is listed in
the
Tech nical D ata s e ction ¢ page 257.
To avoid fuel spill ing or evaporating from the f uel
tank always close fuel cap p roperly and com­
p letely. An improperly closed fue l filler cap may
also cause the MIL lamp
r:!> pag e 25 to come on.
A WARNING
Not paying attention when fueling or han­
dling fuel incorrectly can lead to fires, exp lo­
sions or serious in juries.
- Fuel ignites easily and can cause serious burns and other injuries .
- If you do not switch the eng ine off when fu­
eling and/or do not insert the fuel no zzle
completely into the tank opening, fue l can
leak out or run over . Leaked fuel can ignite
and start a fire .
- Do no t use the telephone while fueling. The
electromagnet ic rays can cause sparks,
wh ich can ignite fuel vapors and start a fire .
- Do not s it in your vehicle while fueling . If
you must make an except ion and enter your
vehicle again wh ile fue ling , close the door
and touch meta l to discha rge static electric­
ity befo re touching the fue l nozzle . Static
electricity can create spar ks, wh ich can ig­
ni te vapors when fue ling.
- Do not smoke or have an open flame i n the
area when fueling your vehicle or filling a
fuel container because this increases the
risk of a n explosion .
- For your safety , carrying fuel containers in
your vehicle is not recommended . Whether
full or empty, the container can leak and cause a fire in the event of an accident.
- If you must make an exception and trans­
port a fuel container, note the following:
- Never fill the fuel containe r with fuel
while it is in or on the vehicle. Stat ic elec­
tr icity is d ischa rged when filling wh ich can
cause the f uel vapors to ignite and in­
creases the risk of an explos ion .
- Always p lace a fuel containe r on the
g round before fi lling .
- Always ho ld the fuel no zzle comp letely in
the fuel container when filling.
Ch eck ing and Filling
-If the fuel container is made of metal, the
fuel nozzle must always be in contact with
the container when filling it with fuel. This prevents stat ic electricity from discharg­
ing .
- Never spill fue l in the vehicle or the lug­
gage compartment. Evaporated fuel is ex ­
plosive and increases the risk of serious in­
ju ry or death .
- Follow legal req uirements when using,
stor ing and transporti ng fuel containers.
- Make sure the fuel container conforms to
industry standards (ANSI/ASTM F852-86).
CD Note
- Remove spilled fuel from vehicle pa int im­
mediately , because it can damage paint.
- Never drive unt il the fuel tank is complete ly
empty. The irregular supply of fue l that re­
sults from that can cause eng ine misfires .
Uncombusted fuel will enter t he exhaust
system and increase the risk of damage to
the catalyti c converter .
CD Note
Applies to: vehicles with diesel engines
If the f uel tank ru ns completely empty, the
i gni tion must remain sw itched on for a t least
30 seco nds after refueling before sta rting the
engine . It may take longer than usua l for the
engine to start, even up to a minute. This is
because the air must first bleed out of the
fuel system when start ing the engine .
@ For the sake of the environment
Do not overfill the fuel tank, otherwise fuel
can leak out when the veh icle is warming up.
(D Tips
The fuel filler door on your vehicle does not l ock if you lock the ve hicle from the ins ide.
(D Tips
Applies to: vehicles with diesel e ngin es
Diesel veh icles are equipped w ith a misfueling
guard
l )_ It a llows the vehicle to be fueled on-
l y w ith a diesel fuel p ump nozzle .
IJJ,,
193

Checking and Filling
& WARNING
AdBlue can irritate the skin, eyes and respira­tory system. If there is contact with the fluid,
flush immediately with plenty of water . Con­
sult a physician if necessary.
(D Note
- Only use Ad Blue that conforms to the
standard ISO 22241 -1. Do not mix any addi ­
tives with the Ad Blue and do not dilute it
with water.
- Do not add Ad Blue to the diesel tank or add diesel fuel to the Ad Blue tank. Do not start
the engine under any circumstances if the
wrong fuel is filled in the tank. There is a
risk of damaging the fuel tank system and
the engine. See an authorized Audi dealer or
authorized Audi Service Facility for assis­
tance.
- AdBlue attacks surfaces such as painted ve­
hicle components, plastic and carpet. Re­
move the fluid as quickly as possible with a
damp cloth and plenty of cold water. If the
Ad Blue has already crystallized, use warm
water and a sponge . AdBlue residue that is
not removed will crystallize and can damage
the affected surface.
- Do not store refill bottles or canisters per ­
manently in the vehicle. If the container
leaks, the escaping AdBlue could damage
the vehicle interior.
- Do not allow AdBlue to come into contact
with clothing. If there is contact with the
fluid , flush immediately with plenty of
wa­
ter.
(j) Tips
Follow the Ad Blue manufacturer 's instruc­
tions for use and storage.
Refilling AdBlue using a bottle
Applies to: vehicles with selective catalytic reduction
... Remove the cap from the refill bottle ¢.&. in
Filling AdBlue on page 196,
c::> (D in Filling
AdBlue on page 196.
196
... Position the bottle on the filler tube and turn
the bottle clockwise until it stops turning.
... Press lightly against the bottom of the bottle
to empty it . Continue pressing the bottom of
the bottle until it is empty or until fluid stops
flowing into the tank .
... Remove the bottle and seal the filler neck
c::> page 197, Completing AdBlue refill.
d) Note
Only use refill bottles that are approved for
your vehicle. Using other systems can cause AdBlue to leak.
(D Tips
- You can obtain refill bottles from an author­
ized Audi dealer or authorized Audi Service
Facility.
- A permitted refill bottle contains approxi­
mately 0.5 gallon (1.9 liters) of AdBlue.
Refilling AdBlue using a canister
Applies to: vehicles with selective catalytic reduction
®
+®
Fig. 179 Canister w ith attachable hose
... Remove the cover from the refill canister c::> .&.
in Filling AdBlue on page 196 , c::>(D in Filling
AdBlue on page 196 .
.,. Secure the end of the hose <Don the opening in
the canister @by turning the hose to the right.
.,. Remove the cap @from the other end of the
hose @.
... Position the end of the hose @on the filler
neck in the vehicle and turn the hose to the
right to tighten it .
... Lift the canister up and then tip it . Continue
holding the canister in a tipped position until it
1J,,