engine AUDI A8 1996 D2 / 1.G 01V Transmission Remove And Install Owner's Manual

37-95

- Only perform vehicle alignment if necessary.

Repair Manual, Suspension, Wheels,
Steering, Repair Group 44; Vehicle alignment


- Install transmission supports at left and right with
transmission mount page 37
-125


Bolt torque converter to drive plate
For vehicles with hex bolts: - Remove bolt -A- after transmission is bolted to engine.
- Apply corrosion protection to contact surface between bolt -A- and oil
pan.

- Bolt torque converter to drive plate via 3 bolts using special tool V175
(turn crank shaft an additional 1/3 turn every time).
Pa
ge 25 of 64 Transmission, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.2

37-96
For vehicles with Torx bolts:

Repair Manual, Electrical Equipment, Repair Group 27; Starter,
removing and installing
- Bolt 3 torque converter bolts to drive plate using respective Torx insert
(turn crank shaft an additional 1/3 turn every time).
- Install starter.
- Install ATF lines to engine/transmission subframe.
- Install bracket for ATF- line.
- Slightly raise engine/transmission subframe at rear via VAG1383A
hoist.

Repair Manual, Suspension, Wheels, Steering, Repair Group 40
- Bolt in engine speed (RPM) sensor -G28- (arrow -B-) at front left of
transmission (if installed).
- Connect connector for speedometer Vehicle Speed Sensor (VSS).
- Bolt drive axles to transmission flanges.
Pa
ge 26 of 64 Transmission, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.2

37-99

Removing and installing for 2.7 Liter 5V turbo
engine:

- Remove bolts (arrows) and remove engine covers -A- and -B-.
- Remove cover above air filter.

- Remove coolant expansion tank (arrows) and lay to side.
- Disconnect connector for coolant level display.
- Remove cover from valve cover (cylinder bank 4-6).
Pa
ge 29 of 64 Transmission, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.2

37-101


- Disconnect connector -1- for oxygen sensor (right side) at bulkhead.
- Expose wire with connector to oxygen sensor.

- Disconnect connectors -2- of left oxygen sensor at bulkhead and
remove lower part of connectors from bracket.
- Expose wire with connector to oxygen sensor.
- Remove all connecting bolts for engine/transmission which can be
reached from the top.
Pa
ge 31 of 64 Transmission, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.2

37-102

- Assemble both 10-222A/3 engine support
adapters for front and rear spindles on support
bar.

- Set 10-222A engine support bridge onto the fender mounting flanges
using 10-222A/1 brackets.
- Hang both spindles on the adapters.
- Secure engine to spindles. To do so, additionally use a shackle -1- at
the rear side of the engine to avoid damage.
- Take up weight of engine/transmission assembly on spindles.
- Tighten the rear spindle less, to enable later lowering at rear.
- Raise vehicle.
- Remove front wheels.

- Remove sound-deadening pan.
- Remove bracket for noise insulation panel.
Pa
ge 32 of 64 Transmission, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.2

37-103


Repair Manual, Suspension, Wheels, Steering, Repair Group 40
- Remove left and right heat shields for drive axles (arrows).
- Disconnect drive axles from transmission drive flanges.

- Unbolt engine speed (RPM) sensor -G28- (arrow B) from transmission
at front left.
- Remove connector for speedometer (arrow -A-) from transmission.
Pa
ge 33 of 64 Transmission, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.2

37-106

- Loosen left and right transmission mounts from
subframe page 37
-125


Note:
When installing, make sure that locating sleeves -2- engage again. - Mark installation positions for threaded assemblies -1- and positioning
sleeves -2-.
- Remove nuts -1- on left and right engine mounts.

Use 3282/19 adjustment plate to position the 3282 transmission support
for Automatic Transmission 01V.
The symbols on the adjustment plate indicate the necessary mounts and
the arrow points toward front of vehicle. - Position 3282 transmission support.
Pa
ge 36 of 64 Transmission, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.2

37-107


Automatic Transmission 01V with All Wheel Drive is supported at the
same positions as the Front Wheel Drive version.
WARNING!
When working on the subframe, all precautions and notes which are
listed in Repair Manual, Suspension, Wheels, Steering must be
must be observed. - Roll VAG1383A engine/transmission hoist with 3282 transmission
support under transmission and support transmission.
- Align adjustment plate parallel to transmission.
- Secure transmission on 3282 transmission support using bolt -A-.

Repair Manual, Suspension, Wheels, Steering, Repair Group 40;
Subframe, removing and installing
- Before loosening carrier, special tool 3393 must be used to check
whether holes -1- and -2- line up.
- Completely lower subframe at rear and front.
Pa
ge 37 of 64 Transmission, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.2

37-108


- Mark installation position of protector shield and hose clamp -1- at left
and right exhaust pipe using a waterproof marker, to quickly find the
correct installation position when re-installing.
- Remove hose clamp -1- from left and right protector shield for
turbocharger.
- Unbolt left and right exhaust pipes -2- from turbocharger.

Repair Manual, Engine Mechanical, Repair Group 26; removing and
installing exhaust system. - Remove heat shield -A- above driveshaft.
- Remove rear part of exhaust system if necessary:- Remove heat shield -2- for driveshaft from cover for Torsen differential
(arrows).
- Unbolt driveshaft from transmission and hang or support.
Pa
ge 38 of 64 Transmission, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.2

37-110

Removing 3 torque converter bolts

If opening -A- is not present, perform the following two work steps to be
able to remove the 3 bolts of the torque converter.
Repair Manual, Electrical Equipment, Repair Group 27; Starter, removing and installing
- Remove plug above opening -A- in engine flange.
- Remove torque converter bolts from drive plate via opening -A- in
engine flange (turn crankshaft 1/3 rotation each time).
- Remove starter.

- Remove torque converter from drive plate by removing 3 bolts using
special tool V175 (turn crank shaft an additional 1/3 turn every time).
Pa
ge 40 of 64 Transmission, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.2