transmission AUDI A8 1998 D2 / 1.G 01V Transmission Oil Pan And Oil Strainer Assembly Owner's Guide

38-38

For transmissions with hydraulic control
E18/2

Removing

- Removing valve body page 38
-22
.

Installing - Unbolt Sensor for transmission RPM -A- from transmission.
- Bolt on Sensor for transmission RPM -A- at transmission via bolt -B-.
Tightening torque is 9 Nm.
Pa
ge 38 of 44 Oil
pan, oil strainer and valve bod
y, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.38.1

38-40

Transmission Vehicle Speed Sensor
(VSS) -G38-, removing and installing


Removing

- Removing oil pan page 38
-19
.

- Disconnect harness connector from Transmission Vehicle Speed
Sensor (VSS) -G38- (arrow).

Installing - Remove Transmission Vehicle Speed Sensor (VSS) -2-.
- Install and tighten Transmission Vehicle Speed Sensor (VSS) -2- using
spacer sleeve -1- (height: 8 mm) to 6 Nm.
Pa
ge 40 of 44 Oil
pan, oil strainer and valve bod
y, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.38.1

38-41


- Connect connector at Transmission Vehicle Speed Sensor (VSS) -
G38-.
- Installing oil pan page 38
-20
.
- Fill up ATF page 37
-140
.
Pa
ge 41 of 44 Oil
pan, oil strainer and valve bod
y, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.38.1

38-42

Wiring harness in transmission,
removing and installing


Removing

- Removing valve body page 38
-22
.

Only for Park/Neutral Position (PNP) Switch -E17- - Lever out retainer straps of connectors at solenoid valves using a small
screwdriver and disconnect connectors -A- in sequence.
- Unhook wiring harness at side retainer straps -B- of valve body.

- Turn valve body on its back side and loosen connector at Sensor for
transmission RPM -1-.
- Remove retaining clip (arrow A) and unclip wiring harness from
retaining clip (arrow B).
- Disconnect connector -2- from Solenoid Valve 4 -N91-.
Pa
ge 42 of 44 Oil
pan, oil strainer and valve bod
y, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.38.1

38-43

Only for transmission with hydraulic control
E18/2

Installing, valid for all:
Installation is reverse of removal, noting the following: - Turn valve body on its back side and loosen connector at Sensor for
transmission RPM -1-.
- Remove retaining clip (arrow A) and unclip wiring harness from
retaining clip (arrow B).
- When installing, connect connectors of wiring harness to the
corresponding solenoid valves.
- Clip wiring harness into the respective retaining clips. In case of
deviations, the wiring harness can be pinched during installation of the
valve body.
- Installing valve body page 38
-25
.
- Fill up ATF page 37
-140
.
Pa
ge 43 of 44 Oil
pan, oil strainer and valve bod
y, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.38.1

38-44

Transmission Fluid Temperature Sensor
-G93-, replacing


Note:
Transmission Fluid Temperature Sensor -G93- is
integrated in the transmission wiring harness.

Removing

- Remove wiring harness in transmission page
38
-42
.

Installing
Installation is the reverse of removal. Also carry
out the following procedure.

- Replace wiring harness with a new one.
Pa
ge 44 of 44 Oil
pan, oil strainer and valve bod
y, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.38.1