AUDI A8 2000 D2 / 1.G AHA Engine Motronic Ignition System User Guide

28-9

- Press buttons corresponding to following display
group numbers and press -Q- button to confirm
input.


022: Display group 22, for cylinders 1 and
2

023: Display group 23, for cylinders 3 and
4

024: Display group 24, for cylinders 5 and
6
Read Measuring Value Block 22 1 2 3 4

Indicated on display (1-4 display groups)
Note:
The test must be carried out during a road test because the knock sensor
system is only active with engine speed greater than 2600 RPM and
engine load greater than 3 ms.
WARNING!
A second technician is required to operate the VAG1551 scan tool
during the road test. Safety precautions page 24
-9 .
- Road test and compare display with specified values for knock sensor
system in display field 1-4.
Pa
ge 11 of 34 Motronic i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.28.1

28-10


Display fields

1 2 3 4
Display group 22 1): Knock control
Display xxx RPM xx.xx ms
xx.x
xx.x
Display Engine speed
(in 40 RPM
steps) Engine load Ignition angle correction 1 Ignition angle correction 2
Work range 0 - 6800 RPM 0.00 - 12.75
ms 0.0 - 12.0
(crankshaft)
0.0 - 12.0
(crankshaft)
Specified
Value ... RPM (test
drive) ... ms (test
drive) 0.0 - 10.0
(crankshaft)
0.0 - 10.0
(crankshaft)

--- --- If displayed values are NOT OK page 28
-11
, Evaluating display
groups 22, 23, 24
1) Display also valid for display groups 23 (cyls. 3 and
4) and 24 (cyls. 5 and
6) .
If displayed values are OK:

-
Press button.

- Press buttons -0- and -6- to select "End Output"
function 06, and press -Q- button to confirm
input.
Pa
ge 12 of 34 Motronic i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.28.1

- Check readiness code page 01
-70
.

If Diagnostic Trouble Code (DTC) memory has
been erased, or ECM has been disconnected,
generate new readiness code page 01
-73
.
Pa
ge 13 of 34 Motronic i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.28.1

28-11
Evaluation of display groups 22, 23 and 24 Display groups: 22, 23 and 24
Possible malfunction
cause
Corrective action
Display fields: 3, 4


All cylinders retarded more than
10 (crankshaft)
Knock sensor faulty- Continuation page 28
-12

Connector corroded
Knock sensor
incorrectly torqued - Loosen knock sensor and tighten to 20 Nm (15 ft lb)
Components loose on
engine - Tighten components
Poor fuel quality- Change fuel
Value for one cylinder different
from the others Connector corroded- Continuation page 28
-12

Engine damage- Check compression Repair Manual, 2.8 Liter V6 5V
Engine Mechanical, Repair Group 15

Components loose on
engine - Tighten components
Pa
ge 14 of 34 Motronic i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.28.1

28-12

Continuation

- Disconnect 3-pin connector from Knock Sensor
(KS) 1 -G61-.

If resistance is OK (no continuity): - Connect multimeter US1119 (Fluke 83 or equivalent) to measure
resistance between connector terminals, using adapters from VW1594
connector test kit.

Connector terminals 1 and 2
Connector terminals 1 and 3
Connector terminals 2 and 3
Specified value:
- Connect VAG1598/22 test box to Motronic ECM harness connector
page 01
-67
.

- Check wiring for open circuit between ECM/test box and 3-pin harness
connector, according to wiring diagram.

Connector terminal 1 to ECM/test box socket 68
Connector terminal 2 to ECM/test box socket 67
Connector terminal 3 to ECM/test box socket 67
Specified value: max. 1.5
Pa
ge 15 of 34 Motronic i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.28.1

28-13


If the wiring is OK:
If the malfunction still exists (stored in DTC memory): - Check wiring for short circuits between terminals of 3-pin connector,
and between connector and ECM/test box.

Connector terminal 2 to ECM/test box socket 68
Connector terminal 3 to ECM/test box socket 68
Specified value:
- Loosen knock sensor and tighten to 20 Nm (15 ft lb).
- Replace Knock Sensor (KS) 1 -G61-.
- Check readiness code page 01
-70
.
If Diagnostic Trouble Code (DTC) memory has been erased, or ECM
has been disconnected, generate new readiness code page 01
-73
.
Pa
ge 16 of 34 Motronic i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.28.1

28-14

- Disconnect 3-pin connector from Knock Sensor
(KS) 2 -G66-.

If resistance is OK (no continuity): - Connect multimeter US1119 (Fluke 83 or equivalent) to measure
resistance between connector terminals, using adapters from VW1594
connector test kit.

Connector terminals 1 and 2
Connector terminals 1 and 3
Connector terminals 2 and 3
Specified value:
- Connect VAG1598/22 test box to Motronic ECM harness connector
page 01
-67
.

- Check wiring for open circuit between ECM/test box and 3-pin harness
connector, according to wiring diagram.

Connector terminal 1 to ECM/test box socket 60
Connector terminal 2 to ECM/test box socket 67
Connector terminal 3 to ECM/test box socket 67
Specified value: max. 1.5
Pa
ge 17 of 34 Motronic i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.28.1

28-15


If the wiring is OK:
If the malfunction still exists (stored in DTC memory): - Check wiring for short circuits between terminals of 3-pin connector,
and between connector and ECM/test box.

Connector terminal 2 to ECM/test box socket 60
Connector terminal 3 to ECM/test box socket 60
Specified value:
- Loosen knock sensor and tighten to 20 Nm (15 ft lb).
- Replace Knock Sensor (KS) 2 -G66-.
- Check readiness code page 01
-70
.
If Diagnostic Trouble Code (DTC) memory has been erased, or ECM
has been disconnected, generate new readiness code page 01
-73
.
Pa
ge 18 of 34 Motronic i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.28.1

28-16

Misfire recognition, checking


Required special tools and test equipment

VAG1551 or VAG1552 Scan Tool (ST) with
VAG1551/3 adapter cable

Checking

- Connect VAG1551/1552 Scan Tool (ST) and
press buttons -0- and -1- to insert "Engine
Electronics" address word 01 (with engine
running at idle) page 01
-8 .
Rapid data transfer
HELP
Select function XX

Indicated on display
- Press buttons -0- and -8- to select "Read Measuring Value Block"
function 08, and press -Q- button to confirm input.
Read Measuring Value Block
HELP
Input displa
y group number XXX

Indicated on display
- Press buttons -0-, -1- and -4- to input display group number 14 (014),
and press -Q- button to confirm input.
Read Measuring Value Block 14 1 2 3 4

Indicated on display (1-4 display groups)
Pa
ge 19 of 34 Motronic i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.28.1

28-17

- Compare displayed values with specified values
for misfire recognition (display fields 3-4):

Display groups

1 2 3 4
Display group 14: Misfire recognition
Display xxx RPM xx.xx ms xxx activated
deact
Indicates Engine speed
(in 40 RPM
steps) Engine load Misfire harmful to emissions (total) Misfire recognition status
Range 0 - 6800 RPM 0.00 - 12.75
ms --- ---
Specified
value 620 - 740 RPM
(all-wheel drive) 1.0 - 2.5 ms 30 activated
740 - 860 RPM
(front-wheel
drive)

--- --- If displayed values are NOT OK page 28
-18
, display groups 15,
16
If displayed values are OK:
Pa
ge 20 of 34 Motronic i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.28.1