oil AUDI A8 2001 D2 / 1.G 01V Transmission Rear Differential Remove And Install Workshop Manual
Page 2 of 8
39-129
3 -
Large tapered roller bearing outer race
1)
Driving out Fig. 7
, page 39
-147
Pressing in Fig. 8
, page 39
-148
4 -
Adjustment shim "S1"
Note thicknessAdjustment overview page 39
-170
5 -
Cover for final drive
1)
With O-ringReplacing O-ringInsert O-ring with oil
6 -
TORX bolt - 25 Nm
7 -
Right gasket Always replace page 39
-113
8 -
Socket head bolt - 25 Nm
Pa
ge 2 of 8 Differential, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.39.12
Page 3 of 8
39-130
9 -
Right drive flange
Removing and installing Fig. 1
10 -
Oil filler plug - 35 Nm
11 -
Differential with ring gear
1)
Disassembling and assembling page 39
-
136
12 -
Oil drain plug - 35 Nm
13 -
Socket
Holds the magnet in positionPress in until stop
14 -
Magnet
15 -
Small tapered roller bearing outer race
1)
Driving out Fig. 1
, page 39
-144
Pressing in Fig. 2
, page 39
-144Pa
ge 3 of 8 Differential, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.39.12
Page 7 of 8
39-134
Differential, removing and installing
Rear final drive removed
Special tools and equipment
Removing
VAG1306 drip tray
- Secure complete rear final drive to assembly stand page 39
-123
.
- Place VAG1306 drip tray underneath and drain gear oil.
- Remove left and right drive flanges.
- To loosen securing bolt, thread 2 bolts into drive flange and counter
hold using tire iron.
- Mark left and right drive flanges.
- Remove drive flange at installed bolts.
- Remove mounting bolts for final drive cover.
- Remove final drive cover from axle housing and remove differential.
Pa
ge 7 of 8 Differential, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.39.12
Page 8 of 8
39-135
Installing
Installation is reverse of removal, noting the
following:
- Install differential.
- Replace O-ring for final drive cover and oil for
installation.
- Install final drive cover onto final drive housing
and tighten in diagonal pattern to 25 Nm.
- Replace drive flange seals page 39
-113
.
- Fill gap between sealing lip and dust lip with
multi-purpose grease.
- Install drive flanges and tighten to 25 Nm.
- Top-up and check gear oil in rear final drive page 39
-94
.
Pa
ge 8 of 8 Differential, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.39.12