battery AUDI A8 2017 User Guide

Driving
-The interior temperature differs from the tem­
perature se lected in the A/C system.
- The windshield is being defrosted~
page 71.
-The brake pedal is pressed seve ral t imes in a
row.
- The vehicle ba tte ry charge leve l is too low.
- Power consumption is high .
Ignition is switched off automaticall y
To prevent the veh icle battery from drain ing, the
ignit ion will switch off
automatically under the
following conditions:
- The vehicle must have already been driven.
- The Start/Stop system has stopped the engine.
- T he driver's door must be open .
- T he driver's safety be lt mus t be unb uck led.
- The brake pedal must not be p ressed .
- The vehicle must be stationary .
In this case, the activated low beam is replaced
by the parking light. The parking lights will
sw itch off after app roximately 30 minutes or
when you lock the vehicle .
If the Start/Stop system has not turned off the
engine or if you have sw itched the Start/Stop sys­
tem off manually, the ignition will not be auto­ mat ically switched off and the engine w ill conti n­
ue to ru n ~ & .
A WARNING
To red uce the risk of poisoning, neve r allow
t he engine to r un i n confined s paces.
(D Tips
If you select the D, N or S selector lever posi­
tion after shifting into reverse, the vehicle
m ust be driven faste r than 6 mph (10 km/h)
in orde r fo r the engine to switch off again.
80
-
Manually switching the Start /Stop system
off /on
Appl ies to : vehicles wi th Start/Stop sys te m
If you do not wish to us e th e system, you con
switch i t off manually.
Fig . 93 Ce nte r console: Start/Stop system butto n
.,. To switch the Start/Stop-System off/on man­
ually, press the
l (A) ~I button. The LED in the but­
ton turns on when the system is switched off.
0) Tips
If yo u switch the system off d uring a stop
phase, the engine will start aga in automati­
cally .
Messages in the instrument cluster display
Applies to : vehicles wit h Start/Stop syste m
Start-stop system deactivated: Please restart
engine manually
This message appears w hen spec ific cond itions
are not me t during a stop phase. The S tart/S top
system will
not b e a ble to re sta rt the eng ine. If
the D or R se lector lever positions were engaged,
P will be selected a utomat ically . The eng ine must
be started with the
I START ENGI NE STOPI but­
ton.
Start -stop system: System fault! Currently
unavailable
There is a ma lfunction in the Start/Stop system.
Drive the vehicle to an authorized Audi dealer or
aut horized Serv ice Facility as soon as possible to
have the malfunction corrected .

0 co .... N ,..... N .... 0 0 :c '<t
Setting the display brightness
Appl ies to: ve hicles with Audi side assist
The display brightness can be adjusted in the In­
fotainment system.
.. Se lect : the I CAR I function button > Car systems
contro l button > Driver ass ist > Audi side as­
sist .
The display brightness ad justs automat ica lly to
the br ightness of the surroundings, both in the
i n formation and in the warning stage . In very
dark or very bright sur roundings, the automatic
ad ju stment will set t he d isp lay to the m inimum
or maxim um level. In such cases, you may no tice
no change when adjus ting the b rightness, o r the
change may only be no tic eable once the s ur­
r o undings change .
Ad just the b rig ht ness to a level where the d isp lay
in t he inform ation stage wi ll no t dis rup t your
view ahead. If you change the bright ness, the dis­
p lay in the ex terior mirror will brief ly show the
b rightness level in the information stage . The
brightness of the warning stage is linked to the
brightness in the informat ion stage and is ad just­
ed along w ith the information stage.
(D Tips
- Side assist is not active wh ile you are ma k­
i ng the ad justment.
- Your settings are automatically store d and
ass igned to the remote control key being
used.
Messages
A ppl ies to: ve hicles with Audi side assist
If s ide ass ist switches off by itself, the LED in the
button turns off and a message will appear in the
i nstr ument cluster d is pl ay :
Audi side assist: Currently unavailable . No
sensor vision
The rada r senso rs' vision is affected . Do not cover
the area in front of the senso rs with bike wheels ,
sticke rs, dirt o r othe r objects . Clean t he a rea in
fr on t of the senso rs , if necess ary
c> page 105,
fig. 1 21 .
Assist
Audi side assist: currently unavailable
S id e assist c annot be sw itched on at this time be­
ca use there is a ma lfunction ( for example, the
battery c harge leve l may be too low).
Audi side assist: System fault!
T he system canno t gua rantee that it will detect
vehicle s cor rec tly and it has switc hed off. The
senso rs have been moved or are f aulty. H ave the
system checked by an au thorized Audi dealer o r
autho rized Audi Serv ice Facility soon.
Audi side assist: Unavailable when towing
S ide ass ist swit ches off automatically when a fac­
tory -inst alled tra ile r hi tch is con necte d to the
electrical connec tor on the t rai ler . There is no
guarantee the system will switch off when using
a retrofitted trailer hitch. Do not use side assist
when towing a trai ler.
Night vision assist with
pedestrian and wild
animal detection
Description
App lies to : vehicles wit h night vision assist
The night vision assist can detect, highlight and,
if necessary, warn about pedestrians and large wild animals.
N ight v ision assist w ith pedestrian and w ild ani ­
mal detection assists you at nig ht by using an in­
frared camera to monitor the a rea in front of
your vehicle, within the limits of the system. It can d isplay objects up to a distance of approxi ­
mately 1000 feet (300 m) . The thermal image
de te cted by the camera is show n in the inst ru­
ment cluster d is pla y. Warm areas appear lighter
and co ld areas appear d arker.
107

0 co .... N ,..... N .... 0 0 :c '<t
Your vehicle is equipped with an intelligent ene r­
gy management system for distributing electrici­
ty. This s ignif icantly improves the starting abi lity
and increases the vehicle battery life.
The energy management system Is made up of
batt ery diagno sis , idling current management ,
and dynam ic energ y man agement.
Battery diagnosis
The batte ry diagnosis de termines the vehicle bat ­
tery charge level. The sensors determ ine the bat ­
tery voltage, the battery current, and the battery
temperature. The current charge level and the performance of the vehicle battery are deter­
mined based on th is.
Idling curr ent manag ement
The idling current management decreases the
energy used whi le parked . With the engine
switched off, it manages the energy distribution
to the different electrical components. Data from
the battery diagnosis is taken into account for
this .
Depending on the vehicle battery charge level,
e lectrical equipment is sw itched off one item af ­
ter the other to prevent the vehicle battery from
draining and to maintain the starting ability .
Dynamic en erg y manag ement
While driving, dynamic energy management dis­
tr ibutes the appropriate amount of energy to the
e lectrical equipment. It controls the battery
charge level so that the amount of energy is not
greater than the amount being generated in or­
der to ma inta in an optimal veh icle battery charge
l evel.
(D Tips
- Energy management cannot overcome the
laws of physics . Note that the charge level
and length of the vehicle battery life a re
limited .
- When the start ing ability is endangered, the
(•) indicator light turns on
9 page 21.
Intellig ent Technology
What you should know
Maintaining the starting ability is the highest
priority .
A lot of stress is placed on the veh icle battery
when driving short distances, during city driving, and at cold times of the year . A lot of energy is
used but little is generated. It is also critical
whe n the eng ine is not r unni ng but elect rical
equipmen t is switched on . In this case, energy is
u sed but none is generated.
In situat ions like th is, energy management w ill
active ly regulate the distrib ution of energy.
Long period s without use
If you do not drive your vehicle for severa l days or
weeks, electrical equ ipment is gradually scaled
back or sw itched off. This reduces energy use and
ensures the vehicle will be ab le to start after long
per iods of time. Some conven ience f unctions,
s u ch as interio r lig hting or power seat adjust­
ment, may no t be av ailable under certain circum­
stances . These conven ience f unctions wi ll be
available again once you sw itch the ignition on
and start the engine.
With the engine switched off
T he veh icle ba tte ry w ill dr ain if you use Info tain­
ment functions such as listening to the radio
whi le the engine is switched off.
If the sta rting abili ty is impaired by the energy
u se, the following message will appear in the In ­
fotainment system display:
Please start the engine , otherwi se the system
will turn off shortl y.
This message indicates that the system will
switch off automatically after 3 m inutes . If you
would like to continue us ing the funct ions, you
must start the engine.
With the engine running
Although e lectr ica l energy is generated while
driv ing, the ve hicle battery can drai n. This can
happen if litt le energy is generated b ut much is
used , and the charge level of the vehicle battery
is not optimal. .,.
131

Intelligent Technology
To restore the balance of energy, components
that require large amounts of energy are tempo­
rarily scaled back or switched off. Heating sys­
tems in particular require a great deal of energy .
If you notice, for example, that the seat heating"
or rear window defogger is not working, then it has been temporarily reduced or switched off .
These systems are available again as soon as the
energy supply has been restored.
In addition, you may notice that the idle speed
has slightly increased. That is normal and no
cause for concern . By increasing the idling speed,
the additional requ ired energy will be generated
and the vehicle battery will be charged.
Notice about data
recorded by the Event
Data Recorder and
vehicle control modules
Event Data Recorder
This vehicle is equipped with an Event Data Re­
corder (EDR). The main purpose of an EDR is to
record, in certain crash or near crash-like situa­
tions , such as an airbag deployment o r hitting a
road obstacle, data that will assist in understand­
ing how a vehicle 's systems performed. The EDR
is designed to record data related to vehicle dy­
namics and safety systems for a short period of
time, typically 30 seconds or less. The EDR in this
vehicle is designed to record such data as :
- How various systems in your vehicle were oper­
ating;
- Whether or not the driver and passenger safety
belts were buckled/fastened;
- How far (if at all) the driver was depressing the
accelerator and/or brake pedal; and,
- How fast the vehicle was traveling.
These data can help prov ide a better understand­
ing of the circumstances in which crashes and in­
juries occur. NOTE: EDR data are recorded by your
vehicle only if a non-trivial crash situation occurs ;
no data are recorded by the EDR under normal
driving conditions and no personal data (e .g.,
name, gender, age, and crash location) are re­
corded. However, other parties, such as law en-
132
forcement, could combine the EDR data with the
type of personally identifying data routinely ac­
quired during a crash investigation.
To read data recorded by an EDR, special equ ip­
ment is required, and access to the vehicle or the
EDR is needed . In addition to the vehicle manu­
facturer, other part ies, such as law enforcement,
that have the special equipment, can read the in­
formation if they have access to the vehicle or the
EDR .
Some state laws restrict the retrieval or down­
loading of data stored by ED Rs installed in a vehi­
cle for the express purpose of retrieving data af­
ter an accident or crash event without the own ­
er 's consent .
Audi will not access the EDR and/or simi lar data
or give it to others -
- unless the vehicle owner (or lessee if the vehi ­
cle has been leased) agrees; or
- upon the official request by the police; or
- upon the order of a court of law or a govern-
ment agency; or
- for the defense of a lawsuit through the judicial
discovery process.
- Audi may also use the data for research about
veh icle operation and safety performance or
provide the data to a third party for research
purposes without identifying the specific vehi­
cle or information about the identity of its own ­
er or lessee and only after the recorded vehicle
data has been accessed.
Vehicle control modules
Your vehicle is also equipped with a number of
electronic control modules for various vehicle
systems, such as engine management, emission control, airbags, and safety belts.
These electronic control modules record data during normal vehicle operation that may be
needed by trained technicians for diagnostic and
repair purposes. The recording capability of these
modules is limited to data (no sound is record­
ed) . Only a small amount of data is actually re­
corded over a very limited period of time, or stor­
ed when a system fault is detected by a contro l
module . Some of the data stored may relate to .,._

0 co .... N ,..... N .... 0 0 :c '<t
Clearing the Jukebox
Requirement: the Jukebox must contain audio/
video fi les.
- Selecting fil es/fo ld ers : se lect the Settings con­
t rol button
> De lete jukebo x > individual files
or folders.
Press the All control button to select
all fi les or folders.
Or : select and confirm a
fo lder and press and hold the control knob . A ll
files in the folder are se lected for de leting .
-Deleting files and folder s: select the Start de­
leting
control button > Y es. T he status of the
deleting process is shown in the Infotainment
display. Jukebox playback stops dur ing the de­
let ing process and starts again automatically
once the deletion is complete .
Showing m emory cap acity
Select: Setting s control b utton > Jukebo x memo­
r y.
The used/free Jukebox memory as well as the
number of stored tracks appear in the Infotain­
ment d isplay.
The Jukebox is started and operated through the MMI
¢ page 189.
@ Note
Do not import audio/video files when the en­
gine is t urned off because this will drain the
veh icle battery.
@ Tips
- Tracks from audio CDs cannot be imported
to the Jukebox for legal reasons.
- Files already imported are recognized and will be grayed out when setting up a new i mport.
- It is not possible to play audio/v ideo files in
t h e DVD dr ive while importing them.
- The Jukebox does not provide an export
function due to lega l reasons .
- Files or tracks without stored information
are listed as
Unkno wn. Audi recommends
adding addit iona l information (s uch as 103
tags) to aud io files.
- Reset the Jukebox to the facto ry defau lt set­
tings when selling your vehicle¢
page 206.
Media dr ives and conn ections
Bluetooth audio player
App lies to : vehicles wi th Blue toot h int erface
You can play music wirelessly from your cell
phone through the MMI using the Bluetooth au­
dio player.
Requirement: the vehicle must be stationary. The
B luetooth function on the portab le aud io player
and the MMI
Aud io pla yer must be switched on
¢ page 155.
.,. Select the I MEDIAi button > Source control but­
ton
> Bluetooth audio player> Find new Blue­
tooth audio player .
The available Bluetooth au­
dio players are d isplayed .
.,. Select and confirm the des ired Bluetooth audio
player from the l ist .
.,. Select and confirm
Audio player . The MMI gen­
erates a PIN for the con nection.
.,. Sele ct and confirm
Yes .
.,. Enter the PIN for connecting on your cell
phone .
Or: if the PIN is a lready displayed on
your cell phone, confirm it in the ce ll phone and
in the MMI. The t ime allowed for enter ing the
PIN is limited to approximate ly 30 seconds.
The media are started and operated through the
portable device o r the MMI, depending on the de­
vice being used
¢ page 189.
@ Tips
-Be sure to pay attention to any possible con ­
nection prompts on your Bluetooth audio
player.
- You only have to pai r your device one time .
Bl uetooth devices that are already paired
are automatically connected to the MMI as
soo n as they are in range.
- Severa l Bluetooth audio players can be con­
nected to the MMI, but only one portab le
device can be active.
- Bluetooth A2DP and AVRCP (1.0/1.3) are
supported.
- The supported media fu nctions depend on
the Bluetooth aud io player being used.
- For more informat ion on the suppo rted de­
vices, v is it
www .audi.com /bluetooth or
contact your authorized Aud i dea ler or a u­
thorized Aud i Serv ice Fac ility.
183

Media drive s and conn ections
Troubleshooting
Problem Solution
Aud i music inte rface /Blueto oth
Refer to the information on the Audi music interface¢ page 185/
audio pla yer : the portab le aud io Bluetooth audio player*¢ page 183. You can learn about support-
device/Bluetooth aud io player is ed dev ices in the Audi database for mobile devices at
not supported.
www .aud i.com /b lue tooth .
Au di music interface :
When start- Adjust the volume of the portable device to approximate ly 70 per-
ing the p layback through the 3 .5 cent of the maximum output
( Input level )¢ page 190 .
mm stereo jack adapter cable*/AV
adapter cab le*, the volume is too
high.
Audi mu sic inte rface: the porta- F
or many ce ll phones or med ia p layers, playba ck is not possible
ble device is not recognized as a when the battery leve l is too low (less than 5% of its capacity).
source. The portable device will on
ly be recognized as a so urce in the MMI
after connecting if the battery charge is sufficient .
Audi music interface: malfunc- The Audio player function is switched On . Switch th is function Off
t ions du ring audio playback when yo u are not using the Bluetooth aud io player*.
through an iPod/ iPhone.
Aud i music in te rface: there is The Audi music interface source is already selected when connect-
static when connecting or discon- ing or disconnecting . Either mute the portable device or sw itch to
nect ing t he 3 .5 mm stereo jack*/ a nother audio source (such as the rad io
¢ page 177) before con-
AV adapter cable* or when con- necting or disconnecting the po rtable devi ce.
nect ing o r disconnect ing the port-
able device to the 3 .5 mm stereo
jack */AVadapter cable *.
Bluetooth audio pla yer: audio Only one interface should be act ively used at a time to ensure
playback inte rference . problem-free playback .
Jukebox: songs on the imported When importing
playlists, a ll of the files themselves must be im-
playlist are grayed out. ported.
Wi-Fi audio pla yer*: the audio/ To avoid in terruptions d uring aud io/video playback, deactivate the
video playback is inter rupted. power saving function o n the Wi -Fi med ia p layer* or connec t it to
a charger.
Wi-Fi hotspot *: your Wi-Fi device Make sure the network optim izat io n functions are sw itched off in
is d isconnected from the W i-F i the Wi-Fi settings or in the network settings for your W i-F i dev ice.
hotspot . For addit ional info rmation refer to the user guide for your Wi-Fi
dev ice.
188

Rear Seat Entertainment
Labeling the wireless headphones
-Attach the supplied label CD or@ c::> fig. 209 on
the inside of the left/right wire less head­
phones.
La beling the w ireless headphones:
CD Wireless headphones label (paired with the
left RSE display)
@ Wireless headphones label (paired with the
right RSE display)
Switching wireless headphones on/off
- Switching on:
to switch the wire less head­
phones on, press the On/Off button<!)
CD
9 fig. 208 on the right earpiece (R) for approxi­
mately
3 seconds and release it once the LED
@ starts blinking . The light @will blink s lowly
once the connection to the wireless head­ phones has been established.
- Switching off : to switch the wireless head­
phones off, press and hold the On/Off button<!)
CD until the LED @turns off.
The wireless headphones switch off automatical­ ly about five minutes after the RSE switches off.
Disconnect wireless headphones
You can delete the pairing between the wireless
headphones and the RSE if yo u need to switch
out the headphones o r change the pairing .
- Select:
I M ENU I button> Setup RSE control but­
ton
> Headphones > Delete wireless head ­
phones.
A WARNING
- For safety reasons, as the driver, only use
the headphones when the vehicle is station­
ary to reduce the r isk of a crash .
- When driving, store the headphones secure­
ly so that they do not move around in the
vehicle interior when braking or in a crash.
- Maintain a moderate volume leve l when lis­
tening to audio playback through the head­
phones. Continuous exposure to extreme
volume levels may result in loss of hearing.
198
-
@ Tips
-If the wire less headphones were already
paired, the connection to the headphones
will be reestablished after switching the
RSE on if the headphones are sw itched on.
- The RSE only supports wireless headphones
from your authorized Audi dealer.
- Audio/video output through the wire less
headphones stops during the pairing proc­
ess.
- The pairing process must be done separate­
ly for the left and right w ireless head­
phones. The wireless headphones are as­
signed to the left or right RSE display de­
pend ing on the side of the RSE control unit
where you started the pairing process. The
pairing between the wireless headphones
and the lef t/r ight RSE display is ide ntifi ed
with a label.
- Volume that is too high or too low is auto­
matically adjusted to a preset leve l when
the wireless headphones are connected.
Charging and changing the battery
Applies to: vehicles with Rear Seat Entertainment
If the light on the wireless headphones turns
red the batteries are low and need to be charg-
,
ed or replaced .
Fig. 210 Connec tion for the charg ing cable/battery com­
partm ent
-Charging the battery : connect the charging ca­
ble to the connection
CD c::> fig . 210 on the bot­
tom side of the left earpiece (L) . Then connect
the charging cable to the cigarette lighter * /12
Volt socket* in the rear center console.
Or:
charge the battery for the wireless headphones .,.

0 co .... N ,..... N .... 0 0 :c '<t
with the mini USB adapter cable through the
Audi music interface ¢
page 185.
-Ch angin g th e batt erie s: turn the cover @
¢ fig. 210 on the left earpiece (L) to the left/
right and change the batteries as labeled in the
battery compartment. Then attach the cover
back on to the left earpiece (L).
You can identify the charge status of the battery
¢
table on page 199 based on the blinking
speed
of the L ED in the charging cable connec­
tion ©¢
fig. 210 .
Blinking fre- Charge status
quency
Blinking The batteries are charging.
Remains on The batteries are charged.
Blinking An error occurred while charg-
quickly ing .
..&, WARNING
-Do not use damaged rechargeable batteries.
T h is increases the r isk of an explos ion.
- T he headphones can become warm when
the batteries a re charg ing and increase the
risk of inj ury.
- Do not cha rge standard batteries with the
charg ing cable. This increases the risk of an
exp losion .
- Be careful when using the c igarette lighter.
Inattentive or unsupervised use of the c iga­
ret te lighter can cause burns.
- T he cigarette lighter/sockets and any elec­
trical accessories connected to them func­
tion only when the ignition is switched on .
Using the cigarette lighter/sockets or elec­
trical accessories incorrectly can lead to se­ rious injur ies or cause a f ire. To reduce the
risk of injuries, never leave children unat­
tended in the vehicle with the vehicle key.
(D Note
- Do not charge the batteries in the wireless
headphones when the engine is not run­
ning. This w ill dra in the vehicle battery.
- For wireless headphones, only use batteries
that are approved for that type of device,
for example NiMH batteries with a min i-
R ear S eat Ent ertainm ent
mum capacity of 550 mAh in AAA size that
are suitable for quick charging.
~ For the sa ke of the environment
Batter ies contain polluting substances. They
must be disposed of using methods that wi ll
not harm the environment. Do not dispose of
them in househo ld trash .
(D Tips
The charging time for the included rechargea ­
ble batteries is approximate ly three to four
hours and may increase by approximately 25
percent if the batteries are in use while charg­
ing .
Headphones connected by cable
App lies to: vehicles wit h Rear Seat Enterta inmen t
The headphone connections ore located on the
RS£ control uni t.
Fig. 211 Conn ecting w ired headphones
"'I nsert th e headphone connecto r into the left or
r ight jack ©¢
fig. 211 on the RSE control pan­
el.
The unit is equ ipped w ith 3.5 mm stereo jacks .
The w ireless headphones sw itch off automatical­
ly about five minutes after the cable headphones
are connected .
(D Tips
Volume that is too high or too low is auto­ matically ad justed to a preset level when the
wired headphones are connected .
199

Airbag syste m
service action is entered in your Audi War­
ranty
& Maintenance book let under AIRBAG
REPLACEMENT RECORD.
- For safety reasons in severe accidents, the
alternator and starter are separated from
the vehicle battery with a pyrotechnic circuit interrupter.
- Work on the pyrotechnic circuit interrupt­
er must only be performed by a qualified
dea ler· risk of an accident!
- If the veh icle or the circuit interrupter is
scrapped, all applicab le safety precautions
must be followed .
@ For the sake of the environment
Undeployed airbag modu les and pretension ­
ers might be classified as Perch lorate Materi­
al -special handling may apply, see
www .dtsc.ca.gov/hazardouswaste/perchlo­
rate. When the vehicle or parts of the re­
straint system including airbag modules and
safety belts w ith pretensioners are scrapped,
all applicable laws and regulations must be
observed. Your authorized Audi dealer is fa­
m iliar with these requirements and we recom­
mend that you have your dealer perform this
serv ice for you .
Other things that can affect Advanced
Airbag performance
Changing the vehicle's suspension system can
change the way that the Advanced Airbag System
performs in a crash. For example, using t ire-r im
comb inat ions not approved by Audi, lower ing the
veh icle, chang ing the st iffness of the suspens ion,
including the springs, suspension struts, shock
absorbers etc. can change the forces that are
measured by the airbag senso rs and sent to the
electronic contro l unit. Some suspension changes
can, for example, increase the force levels meas­
ured by the sensors and make the airbag system
deploy in crashes in which it would not deploy if
the changes had not been made. Other kinds of changes may reduce the force levels meas ured by
the sensors and prevent the airbag from deploy­ ing when it should .
240
A WARNING
Changing the vehicle's suspension including
use of unapproved tire-rim comb inations can
change Advanced Airbag performance and in­
crease the r isk of serious personal injury in a
crash.
- Never insta ll suspension components that
do not have the same performance charac­
ter istics as the components origina lly ins tal­
led on you r vehicle.
- N ever use tire-r im combinations that have
no t been approved by Aud i.
A WARNING
It ems stored between the safety belt buckle
and the center conso le can cause the sensors
in the buckle to send the wrong information
to the electronic contro l module and prevent
the Advanced A irbag System from working
proper ly.
- Always make sure that nothing can interfere
with the safety belt buckles and that they
are not obstructed.
Knee airbags
Description of knee airbags
The knee airbag system can provide supplemen­
tal protection to properly restrained front seat
occupants.
Fig . 234 D river 's knee a irbag
The driver knee airbag is in the instrument panel
underneath the steering wheel~
fig. 234, the
airbag for the passenger is at about the same height in the instrument panel underneath the
glove compartment . ..,_

Checking and Filling
-Set the parking brake.
- Select the P selector lever position.
- Let the engine cool down.
- Never open the hood when there is steam or
coolant escaping from the engine compart­
ment, because there is a risk that you could
be burned. Wait until no steam or coolant is
escaping.
- Keep children away from the engine com­
partment.
- Never spill fluids on a hot engine. These flu­
ids (such as the anti-freezing agent con­
tained in the coolant) can ignite.
- Avoid short circuits in the electrical system.
- When working in the engine compartment,
remember that the radiator fan can switch
on even if the ignition is switched off, which
increases the risk of personal injury.
- Never open the cap on the coolant expan­
sion tank when the engine is warm. The
cooling system is under pressure.
- To protect your face, hands, and arms from
hot steam or coolant, cover the cap with a
large cloth when opening.
- Do not remove the engine cover under any
circumstances. This increases the risk of
burns.
- If tests need to be performed with the en­
gine running, there is additional danger due
to moving components (such as the ribbed
belt, alternator and radiator fan) and from
the high-voltage ignition system .
- Do not under any circumstances activate the
throttle inadvertently (for example, by hand
from the engine compartment) if the vehi­
cle is stationary but the engine is running
and a gear is engaged. Otherwise, the vehi­
cle will start to move immediately and this
could result in an accident.
- Pay attention to the following warnings list­
ed when work on the fuel system or on the
electrical equipment is required.
- Do not smoke .
- Never work near open flames.
- Always have a working fire extinguisher
nearby
- All work on the battery or electrical system
in your vehicle can result in injuries, chemi-
272
cal burns, accidents or burns. Because of
this, all work must be performed
only by an
authorized Audi dealer or authorized Audi
Service Facility .
- To reduce the risk of electric shock and in­
jury, never touch the following components when the engine is running or is being start­
ed:
- Ignition cable
- Other components in the electronic high-
voltage ignition system
- If you must check or perform work on the
engine while it is running:
- Set the parking brake and place the selec­ tor lever in the P (park) position first.
- Always proceed with extreme caution so
that clothing, jewelry or long hair do not
become caught in the radiator fan, fan
belt or other moving components or do
not come into contact with hot compo­
nents . Tie back long hair before beginning
work and do not wear clothing that can
hang down into the engine .
- Limit your exposure to exhaust and chemi­
cals to as short a time as possible
c:> ,&. .
.&_ WARNING
California Proposition 65 Warning:
- Engine exhaust, some of its constituents,
and certain vehicle components contain or
emit chemicals known to the State of Cali­
fornia to cause cancer and birth defects and
reproductive harm. In addition, certain flu­
ids contained in vehicles and certain prod­
ucts of component wear contain or emit
chemicals known to the State of California
to cause cancer and birth defects or other
reproductive harm .
- Battery posts, terminals and related acces­
sories contain lead and lead compounds,
chemicals known to the State of California
to cause cancer and reproductive harms .
Wash hands after handling.