tow AUDI Q3 2017 Owner´s Manual

Intelligent Technology
gear or lower driving range. Do not ride the
brakes or hold the pedal down too long or
too often. This could cause the brakes to get hot and diminish braking efficiency .
- Do not "ride the brakes" by resting your foot
on the pedal when you do not intend to
brake. This may cause the brakes to over ­
heat, premature wear and increased stop­
ping distance.
- Under certain climatic and operating condi­
tions such as passing through water, driving in heavy rain or after washing the vehicle ,
the effectiveness of the brakes can be re­
duced . In winter, ice can accumulate on the
brake pads, linings, discs and drums . Care­
fully apply brakes for a test. Brakes will dry and ice coatings will be cleaned off after a
few careful brake applications.
- Driving for an extended period of time on
salt-covered roads without using your
brakes can also affect braking efficiency .
Clean off accumulated salt coating from
brake discs and pads with a few careful
brake applications .
- If you damage the front spoiler, or if you in­
stall a different spoiler, be sure the air flow
to the front brakes is not obstructed. Other­
wise the brake system could overheat reduc­
ing the effectiveness of the entire brake sys­
tem.
- Failure of one brake circuit will impair the
braking capability resulting in an increased
stopping distance. Avoid driving the vehicle
and have it towed to the nearest authorized
Audi dealer or qualified workshop.
- Never let the vehicle roll to a stop with the
engine shut off.
- If the brake booster is not working, the
brake pedal must be pressed considerably
harder to make up for the lack of booster
assistance.
96
Electromechanical
steering
The electromechanical steering supports the
driver's steering movements .
Power steering adapts electronically based on
the vehicle speed .
Indicator lights and messages
• Steering fault! Do not drive vehicle!
If this indicator light turns on and stays on and
this message appears, the power steering may
have failed.
Do
not continue driving . See an authorized Audi
dealer or authorized Audi Service Facility for as­
sistance.
If the indicator light turns on, the steering wheel
may be more difficult to move or more sensitive
than usual. The steering wheel may also be at an
angle when driving straight.
Drive slowly to an authorized Audi dealer or au­
thorized Audi Service Facility to have the mal ­
function corrected .
(;r, lj Steering lock: System fault! Please contact
dealer.
There is a malfunction in the electronic steering
lock.
Drive to an authorized Audi dealer or authorized
Audi Service Facility immediately to have the malfunction corrected.
A WARNING
Have the system malfunction corrected as
soon as possible by an authorized Audi dealer
or authorized Audi Service Facility, as this in­
creases the risk of an accident .
{!) Tips
If the . or 'T j indicator light only stays on
for a short time, you may continue driving.
-

Driving safety
For detailed information on how to adjust the
driver's seat, see ¢
page 44.
A WARNING
Drivers who are unbelted, out of position or
too close to the airbag can be seriously in­
jured by an airbag as it unfolds. To help re­
duce the risk of serious personal injury:
- Always adjust the driver's seat and the
steering wheel so that there are at least
10 inches (25 cm) between your breastbone
and the steering wheel.
- Always hold the steering wheel on the out­
side of the steering wheel rim with your
hands at the 9 o'clock and 3 o'clock posi­
tions to help reduce the risk of personal in­
jury if the driver's airbag inflates.
- Never hold the steering wheel at the
12 o'clock position or with your hands at
other positions inside the steering wheel
rim or on the steering wheel hub. Holding
the steering wheel the wrong way can cause serious injuries to the hands, arms and head
if the driver's airbag deploys.
- Pointing the steering wheel toward your
face decreases the ability of the su pplemen­
tal driver's airbag to protect you in a colli­
sion.
- Always sit in an upright position and never lean against or place any part of your body
too close to the area where the airbags are
located.
- Before driving, always adjust the front seats
and head restraints properly and make sure
that all passengers are properly restrained.
- Never adjust the seats while the vehicle is
moving . Your seat may move unexpectedly
and you could lose control of the vehicle.
- Never drive with the backrest reclined or
tilted far back! The farther the backrests are
tilted back, the greater the risk of injury due
to incorrect positioning of the safety belt
and improper seating position.
- Children must always ride in child safety
seats¢
page 137. Special precautions ap­
ply when installing a child safety seat on the
front passenger seat
q page 117.
102
-
Proper seating position for the front
passenger
The proper front passenger seating position is
important for safe, relaxed driving.
For your own safety and to reduce the risk of in­
jury in the event of an accident, we recommend
that you adjust the seat for the front passenger
to the following position :
.,. Adjust the angle of the seatback so that it is in
an upright position and your back comes in full
contact with it whenever the vehicle is moving.
.,. Adjust the head restraint so the upper edge is
as even as possible with the top of your head. If
that is not possible, try to adjust the head re­
straint so that it is as close to this position as
possible ¢
page 45.
.,. Keep both feet flat on the floor in front of the
front passenger seat.
.,. Fasten and wear safety belts correctly
¢page 112.
For detailed information on how to adjust the
front passenger's seat, see
¢ page 44.
A WARNING
Front seat passengers who are unbelted, out
of position or too close to the airbag can be
seriously injured or killed by the airbag as it
unfolds. To help reduce the risk of serious
personal injury:
- Passengers must always sit in an upright po­
sition and never lean against or place any
part of their body too close to the area
where the airbags are located.
- Passengers who are unbelted, out of posi­
tion or too close to the airbag can be seri­
ously injured by an airbag as it unfolds with
great force in the blink of an eye.
- Always make sure that there are at least
10 inches (25 cm) between the front pas­
senger's breastbone and the instrument
panel.
- Each passenger must always sit on a seat of
their own and properly fasten and wear the
safety belt belonging to that seat.
- Before driving, always adjust the front pas­ senger seat and head restraint properly.

a:,
a:,
...... N r--. N .... 0 0 ::, a:,
-Never place any objects in the driver's foot­
well. An object could get into the pedal area and interfere w ith pedal function. In case of
sudden braking or an accident, you would not be able to brake or accelerate!
- Always make sure that nothi ng can fall or
move into the dr iver's footwell.
Floor mats on the driver side
Always use floor mots that con be securely at­
tached to the floor mot fasteners and do not in­
terfere with the free movement of the pedals .
.. Make sure that the floor mats are properly se­
cured and cannot move and interfere with the
pedals
q .&, .
Use only floor mats that leave the pedal area un­
obstructed and that are firmly secured so that
they cannot slip out of position. You can obtain
suitable floor mats from your authorized Audi
dealer .
F loor mat fasteners are installed in your Audi.
Fl oor mats used in your vehicle must be attached
to these fasteners. Proper ly securing the floor
mats will prevent them from sliding into posi­
tions that could interfere with the pedals or im­ pair safe operation of your vehicle in other ways.
A WARNING
Peda ls that cannot move free ly can result i n a
loss of vehicle control and increase the risk of
ser ious personal injury .
-Always make sure that floor mats are prop­ erly secured.
- Never place or install floor mats or other
floo r coverings in the veh icle that ca nnot be
prope rly secured in place to prevent them
from slipp ing and in terfering with the ped­
als or the abili ty to contro l the vehicle.
- Never place or insta ll floor mats or o ther
floo r coverings on top of already insta lled
floo r ma ts. Addit ional floor mats and othe r
coverings w ill reduce the size of the peda l
area and interfere with the pedals .
- Always properly reinstall and secu re floor
mats that have been taken o ut for cleaning .
Driving safety
-Always make sure that objects cannot fall
into the driver footwell while the vehicle is
mov ing. Objects can become trapped under
the brake pedal and accelerator pedal caus­ ing a loss of vehicle control.
Storing cargo correctly
Loading the luggage compartment
All luggage and other objects must be properly stowed and secured in the luggage compart­
ment.
Fi g. 103 Safe load pos ition ing: place heavy objects as low
and as fa r forward as poss ible.
Loose items in the luggage compartment can
shift suddenly, changing vehicle handling charac­
teristics. Loose items can also increase the risk of
serious personal injury in a sudden veh icle ma ­
neuver or in a collision .
.. Distribute the load evenly in the luggage com­
partment.
.,. Always place and properly secure heavy items in
the luggage compartment as low and as far for­
ward as possib le
q fig. 103 .
.. Sec ure luggage usi ng the t ie-downs provided
q pogeSO.
.. Make sure that the rear seatback is secure ly
latched in place .
A WARNING
Improperly stored luggage or other items can
fly through the vehicle caus ing serious per­
sona l injury i n the event of hard brak ing or an
accident. To help reduce the risk of serio us
personal injury :
~
105

Safe ty belts
from the strong bones to more vulnerable,
soft tissue and cause ser ious injury.
- Always read and heed all WARNINGS and
other important information
¢ page 111.
Pregnant women must also be correctly
restrained
T he best way to protect the fetus is to make sure
t hat expectan t mo thers always wear safety bel ts
correctly -throughout the pregnan cy .
Fig. 1 12 Safety belt pos ition duri ng pregna ncy
To prov ide max imum protection , safety belts
m ust always be positioned correctly on the wear ­
er's body
¢ page 113.
• Ad just the fro nt seat a nd head restraint cor­
rec tly ¢
page 44, Front sea ts .
,.. Make s ure the seatback of the rear seat bench
is in an upright position and securely latched in
plac e before using the b elt.
,.. Pull the safety be lt evenly across the chest so
that it sits as low as possible on the pelv is and
there is no pressure on the abdomen
¢ fig . 112, ¢ .&_ .
• Insert the tongue into the cor rect b uckle of
you r seat until you hear it latch secure ly.
,.. Pu ll on t he be lt to make sure that it is securely
latched i n the buck le.
_& WARNING
Improperly positioned safety be lts can cause
serious persona l injury in an accident.
- Expec tant mothe rs must a lways wear the
lap portion of the safety belt as low as pos­
sible across the pelvis and below the round­ ing of the abdomen .
114
-Always read and heed all WARNINGS and
other important informat ion ¢
& in Fasten­
ing safety belts on page 113 .
Unfastening safety belts
Unbuckle the safety belt with the red release
button only after the vehicle has stopped.
Fig. 113 Releasing t he tongue from the buckle
• Push the red re lease button on the buck le
¢ fig. 113 . The belt tongue w ill spri ng out of
t he buck le ¢
.&, .
• Let the belt wind up o n the retractor as yo u
guide the belt tongue to its stowed position.
_& WARNING
Never unfasten safety be lt whi le the vehicle is
moving . Do ing so will increase your risk of be­
ing injured or killed.
Adjusting safety belt height
With the aid of the safety belt height adjust ­
ment, the three point safety belt strap routing
can be fi tted to the shoulder area , according to
body size .
Fig . 11 4 Safety be lt heigh t adj ust me nt for the front seats
- loop -ar ound fittings
Sf 0 0
0
CJ Sf m

00
00
......
"' ,....
"' ...... 0 0 :::,
00
- Never remove the upholstery from the front
passenger seat.
- Never disassemble or remove parts from the
seat or disconnect wires from it.
- Never carry sharp objects in your pockets or
place them on the seat. If the weight-sens­
ing mat in the passenger seat is punctured
it cannot work properly.
- Never carry things on your lap or carry ob­
jects on the passenger seat. Such items can increase the weight registered by the
weight-sensing mat and send the wrong in­
formation to the airbag control unit.
- Never store items under the front passenger
seat. Parts of the Advanced Airbag System
under the passenger seat could be dam­
aged, preventing them and the airbag sys­
tem from working properly.
- Never place seat covers or replacement up­
holstery that have not been specifically ap­
proved by Audi on the front seats.
- Seat covers can prevent the Advanced Air­
bag System from recognizing child re­
straints or occupants on the front passenger
seat and prevent the side airbag in the seat
backrest from deploying properly.
- Never use cushions, pillows, blankets or
similar items on the front passenger seat.
The additional padding will prevent the
weight-sensing mat in the seat from accu­
rately registering the child restraint or per­
son on the seat and prevent the Advanced
Airbag System from functioning properly.
- If you must use a child restraint on the front
passenger seat and the child restraint man­
ufacturer's instructions require the use of a
towel, foam cushion or something else to properly position the child restraint, make
certain that the
PASSENGER AIR BAG OFF
light comes on and stays on whenever the
child restraint is installed on the front pas­
senger seat.
- If the
PASSENGER AIR BAG OFF light does
not come on and stay on, immediately in­
stall child restraint in a rear seating position
and have the airbag system inspected by
your authorized Audi dealer.
Airbag system
How the Advanced Airbag System
components work together
The front Advanced Airbag System and the side
airbags supplement the protection offered by the
front three-point safety belts with pretensioners and load limiters and the adjustable head re­
straints to help reduce the risk of injury in a wide
range of accident and crash situations. Be sure to
read the important information about safety and
heed the WARNINGS in this chapter .
Deployment of the Adv a need Airbag System and
the activation of the safety belt pretensioners de­ pend on the deceleration measured by the crash
sensors and registered by the electronic control
unit. Crash severity depends on speed and decel­
eration as well as the mass and stiffness of the
vehicle or object involved in the crash.
On the passenger side, regardless of safety belt
use , the airbag will be turned
off if the weight on
the passenger seat is less than the amount pro­
grammed in the electronic control unit. The front
airbag on the passenger side will also be turned
off if one of the child safety seats that has been
certified under Federal Motor Vehicle Safety
Standard 208 has been recognized on the seat.
The
PASSENGER AIR BAG OFF light comes on
and stays on to tell you when the front Advanced
Airbag on the passenger side has been turned off
¢page 118, Child restraints on the front seat ­
some important things to know .
_&. WARNING
To reduce the risk of injury when an airbag in­
flates, always wear safety belts properly.
- If you are unrestrained, leaning forward, sit­
ting sideways or out of position in any way,
your risk of injury is much higher.
- You will also receive serious injuries and
could even be killed if you are up against the
airbag or too close to it when it inflates -
even with an Advanced Airbag
¢page 117.
125

00
00
......
"' ,-...
"' ...... 0 0 :::,
00
- Make sure that the PA SSENGER AIR B AG
OFF
light comes on and stays on all the time
whenever the ignition is switched on.
- If the PAS SEN GER AIR BAG OFF light does
not come on and stay on, immediately in­
stall the rear-fac ing ch ild safety seat in a
rear seat ing pos ition and have the airbag
system inspected by your Aud i dealer.
Activating the convertible locking retractor
Use the convertible locking retractor to secure a
child restraint.
Always heed the child safety seat manufacturer's
instructions when installing a ch ild restraint in
your veh icle. To act ivate the convertible locking
retractor:
.. Place the child restraint on a seat, preferab ly
on the rear seat.
.,. Slowly pull the be lt
all th e way out .
.. Route it around or through the c hild restraint
belt path ¢
.&_.
.,. Push the child safety seat down with your fu ll
weight to get the safety be lt rea lly t ight.
.,. Inse rt the bel t tongue into the buckle fo r that
seating position .
.,. Guide the safety be lt back into the retractor un­
til the belt lies flat and snug on the child safety
seat.
.. You should hear a "clicking" noise as the belt
winds back into the inertia reel. Test the con­
vertible locking retractor by pulling on the belt .
You should no longer be able to pull the belt
out of the ret ractor. The conve rtible locking re­
tractor is now ac tivated .
.,. Make s ure that the red release button is fac ing
away from the child restraint so that it can be
unbuckled quick ly.
.. Pull on the be lt to make sure the safety belt is
properly tight and fastened so that the seat
cannot move forward or sideways more than
one inch (2 .5 cm).
A WARNING
Using the wrong child restra int or an improp­
erly installed ch ild rest raint can cause ser ious
personal in jury o r death in a crash.
Ch ild safety
-Always make sure that the safety be lt re­
tractor is locked when installing a child
safety seat. An unlocked safety be lt retrac­
tor cannot hold the ch ild safety seat in place
during normal driving or in a crash .
- Always buckle the child safety seat firmly in
place even if a ch ild is not sitt ing in it . A
loose child safety seat can fly a round dur ing
a sudden s top or in a c rash.
- Always make sure the seat backrest to which
the child restraint is installed is in an up­
right position and securely latched into
p lace and cannot fo ld forward. Othe rw ise,
the seatback with the child safety seat at­
tached to it could fly forward in the event of
an accident or other emergency situation.
- Always read and heed all WARNINGS when­
ever using a child restrained in a vehicle is
being used¢
page 137 . Special precautions
apply when install ing a child safety seat on
the front passenger seat ¢
page 118, Child
restraints on the front seat -some impor­
tant things to know .
Deactivating the convertible locking
retractor
The convertible locking retractor for child re­
straints will be deactivated automatically when
the belt is wound all the way back into the re­
tractor .
.. Press the red button on the safety belt buckle.
The belt tongue will pop out of the buck le.
.,. Guide the safety belt all the way back into its
s towed posit io n .
Always let the safety belt retract completely into
its stowed posit ion. The safety be lt can now be
u sed as an ord inary safety belt wit hout the con ­
vertib le locking ret ractor fo r ch ild rest raints .
If the convertible locking retractor should be ac­
t ivated inadverte ntly, the safety belt must be un­
fastened and guided comp lete ly back into its
stowed pos ition to deactivate th is feature. If the
convertible locking retractor is not deactivated,
the safety belt will gradua lly become tighter and
uncomfortab le to wear. ..,.
149

Checking and Filling
-Never f ill the fuel container with fuel
while it is in or on the vehicle. Stat ic elec­
tricity is d ischarged when filling wh ich can
cause the f uel vapors to ignite and in­
creases the r isk of an explos ion .
- Always p lace a fuel container on the
ground before fi lling .
- Always hold the fuel nozzle comp letely in
the fuel container when fi lling .
- If the fue l conta iner is made of metal, the
fue l nozzle must always be in contact wit h
the conta iner w hen filling it w ith fue l. Th is
prevents static electr ic ity from discharg­
ing.
- Never sp ill fuel in the veh icle or the lug ­
gage compartment . Evaporated fue l is ex­
plosive and increases the risk of se rio us i n­
jury o r death.
- Follow legal requireme nts when usi ng,
s t o ring and tran spo rting fuel cont ainers.
- Ma ke sure the fue l conta iner confo rms to
i ndu stry st anda rds (A NSI/ ASTM F852-86).
0 Note
- Remove spilled fuel from vehicle paint im­
mediately, because it can damage paint.
- Never drive until the fuel tank is completely
empty . The ir regular supp ly of fuel that re­
su lts from that ca n cause engine m isfires .
Uncombusted f ue l w ill enter the exha ust
sy stem a nd incr ease t he risk of damage to
the c atalyt ic converter.
@ For the sake of the environment
Do not ove rfi ll the f uel tank, othe rw ise fue l
can le ak out when the vehicle is wa rm ing up.
(0 Tips
The f uel fi ller door on yo ur vehicle does not
loc k if yo u lock the vehicle from the inside .
158
Fuel filler door emergency release
If the cen tral locking system is faulty, the fuel
filler door can be unlocked manually .
Fig. 13 7 Right side trim panel in t he lugg age compar t­
m ent: eme rge ncy rele ase mecha nis m
T he emergency release mechan ism is located be­
hind the right s ide trim panel in the luggage
compartment.
.,. Remove the cover in t he side panel.
.,. Loosen the loop from the retainer -arrow- and
then pull on the loop carefu lly ¢ @ . The f uel
fill er door releases.
.,. Press on t he left s ide of the fue l filler doo r to
open i t¢
page 15 7, fig. 135.
(D Note
Only p ull on t he loo p until yo u feel res ista nce.
You w ill not hea r it re lease. Othe rw ise you
c o uld d amage the emergen cy rele ase mech a­
nism .
Catalytic converter
It is very important that your emission control
system (catalytic converter) is functioning prop­
erly to ensure that your vehicle is running in an
environmentally sound manner .
.,. Always use lead -free gasoline ¢ page 155, Fuel
supply.
.,. Never r un the tank down all the way to empty .
.,. Never put too much motor oi l in your engine
¢ page 164 .
.,. Never try to push- or tow-start your vehicle .
The catalytic conve rter is an efficient "clean-up"
device built into the exhaust system of the veh i-
cle. The catalyt ic converter burns many of the
lilJ,

Wheels
passengers that the vehicle is in­
tended to carry ("seating capaci­
ty") with an assumed weight of 1 SO lbs. (68 kg) for each passen­
ger at a designated seating posi­
tion and the total weight of any
luggage in the vehicle. If you tow
a trailer, the weight of the trailer hitch and the tongue weight of
the loaded trailer must be includ­
ed as part of the vehicle load.
The
Gross Axle Weight Rating
("GAWR") is the maximum load
that can be applied at each of the
vehicle's two axles.
The fact that there is an upper limit to your vehicle's Gross Vehi­
cle Weight Rating means that the
total weight of whatever is being
carried in the vehicle (including
the weight of a trailer hitch and
the tongue weight of the loaded
trailer) is limited. The more pas­
sengers in the vehicle or passen­
gers who are heavier than the
standard weights assumed mean
that less weight can be carried as luggage.
The Gross Vehicle Weight Rating
and the Gross Axle Weight Rating
are listed on the safety compli­
ance sticker label located on the
184
driver's side B-pillar ¢ page 181,
fig. 149.
~ WARNING
Overloading a vehicle can cause
loss of vehicle control, a crash
or other accident, serious per­
sonal injury, and even death.
-Carrying more weight than your vehicle was designed to carry will prevent the vehicle
from handling properly and
increase the risk of the loss of
vehicle control.
-The brakes on a vehicle that has been overloaded may not
be able to stop the vehicle
within a safe distance.
-Tires on a vehicle that has been overloaded can fail sud­
denly, including a blowout and
sudden deflation, causing loss
of control and a crash.
-Always make sure that the to­ tal load being transported -including the weight of a trail­
er hitch and the tongue
weight of a loaded trailer -
does not make the vehicle
heavier than the vehicle's
Gross Vehicle Weight Rating.

00
00
......
"' ,....
"' ...... 0 0 :::,
00
Determining correct load
limit
Use the example below to calcu­
late the total weight of the pas­
sengers and luggage or other
things that you plan to transport
so that you can ma ke sure that
your vehicle will not be overload­ ed .
Steps for Determining Correct
Load Limit
1 . Locate the statement "THE
COMBINED WEIGHT OF OCCU­ PANTS AND CARGO SHOULD
NEVER EXCEED XXX KG OR XXX
LBS"on your vehicle 's pla card
(tire inflation pre ssure l abel)
¢ page 181, fig. 149.
2 . Determine the combined
weight of the drive r and pas­
s engers that will be riding in
your vehicle.
3 . Subtra ct the combined weight
of the driver and passengers
from
" XXX" kilograms or "XXX"
pounds shown on the sticker
¢ page 181 , fig. 149 .
4. The re sulting figure equals the
available amount of cargo and
luggage load capacity. For ex­
ample, if the
" XXX" amount
equals 1400 lbs. and there will
Wheels
be five 1 SO lbs. pa ssengers in
your vehicle, the amount of available cargo and luggage load capacity i s 650 lb s.
(1400-750 (5 X 150) = 650
lbs.)
5. Determin e the combined
weight of luggage and cargo
being loaded on the vehicle.
That weight may not safely ex­
ceed the available cargo and luggage load capa city cal culat­
ed in Step 4 .
6. If your vehi cle will be towing a
trailer, load from your trailer
will be transferred to your ve­
hicle. Con sult thi s manual to
determine how this reduces
the available cargo and lug­ gage load capacity of your vehi­
cle.
..,.Check the tire sidewall
(¢page 171 , fig. 147) to deter­
mine the designated load rating
for a specific tire.
Wheel bolts and rims
Wheel bolts
Wheel bolts mus t be clean and loosen/tig hte n
easily .
Rims
Rims with a bo lted r im ring * or with bo lted w heel
cove rs* cons ist of mult iple p ieces. These compo-
nents were bolted togethe r using s pec ial bolts ..,.
185

Emerg ency assis ta nce
Folding chocks
Applies to: ve hicles w ith fol ding chocks
The folding chocks* are part of the vehicle tool
kit.
-- -,,,.
F ig. 152 Opening the fo lding chocks
• To use the folding chocks, lift up the support
plate (!)¢
fig. 152 and insert them using both
"tabs" into the slotted holes on the base plate
@ ¢_& .
A WARNING
-The folding chock will not work and can lose
its stability if the support plate "tabs" are
not securely fitted in the slots on the base
plate. If th is is the case, the vehicle could
start mov ing when changing a tire.
- Never use fo ld ing chocks that are damaged
o r that were not assembled cor rectly.
Replacing wheels
Before changing a wheel
Observe the following precautions for your own
and your passenger's safety when changing a
wheel.
• After you experience a tire failure, pull the car
well away from moving t raffic and try to reach
l ev el ground before you stop¢
page 197,
¢_& .
• All passengers shou ld leav e th e car and move
to a safe location (for instance, beh ind the
guardrail)
¢ _& .
• Engage the park in g br ake to prevent your vehi­
cle from roll ing unintentionally ¢_& .
• Move the selec to r l eve r to the P po sition.
198
• If you are towing a trai ler : unhitch the t railer
from your veh icle.
• Take the jac k
¢page 197 and the sp are tire
¢
page 203 out of the luggage compartment.
A WARNING
You or your passengers could be injured while
changing a wheel if you do not follow these
safety precaut ions:
- If you have a flat tire, move a safe distance
off the road . Turn off the eng ine, turn the
emergency f lashers on and use other warn­
ing dev ices to alert other motorists.
- Make sure that passengers wait in a safe
place away from the vehicle a nd well away
from the road and traff ic.
- To he lp prevent the veh icle from moving
suddenly and possib ly sl ipping off the jac k,
always fu lly set the par king b rake and block
the whee l diagonally opposite the wheel be­
ing changed with the folding chocks or oth ­
er objects. When one front whee l is lifted
off the ground, placing the Automat ic
Transmission in "P" (Park) w ill
not prevent
the vehicle from moving.
- Before you change a whee l, be sure the
ground is level and firm . If necessary, use a
sturdy board under the jack.
- Always store the vehicle too l kit, the jack
and the replaced tire in the luggage com­
partment
¢ page 105.
(D Note
If you are changing the wheel on a steep in­
cline, use the folding chock¢
page 198 to
block the opposite whee l to prevent the vehi­
cle from moving.
@ Tips
Obey all laws.