change wheel AUDI Q7 2008 4L / 1.G Infotainment MMI Operating Manual

Navigation111
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control You can exit the legend menu by pressing .
Orientation. The map is displayed either facing north or facing
the direction of travel
page 118. If you select the orientation
option in the activated legend menu and press the rotary push-
button, the orientation switches from the direction of travel to
the direction facing north and vice versa. This setting is not
stored.
Scale. Turn the rotary pushbutton clockwise/anti-clockwise to
zoom in or out. You can also change the scale via the activated
legend menu. The setting that was last activated is stored.
Distance to the destination
Estimated time of arrival
Examples of selected map contents
Depiction of motorway exits on a scale of 50 m to 500 m. On a
scale of 750 m to 8 km the exits are displayed as dots.
Location of the vehicle
Destination control button. To switch to entry space

page 105, fig. 91 or the route plan
page 108, fig. 96.
If you use the crosshairs to select map contents, any existing
information on the contents (e.g. address, phone number) will
be displayed. If you select a traffic jam symbol and press the
rotary pushbutton, the corresponding TMC traffic report will be
displayed. On a scale of 1 km upwards, the map contents will
not be displayed.
Display of position coordinates of the crosshairs (longitude and
latitude).
Map position menu. The point on the map selected with the
crosshairs can be set as a destination or stopover, stored in the
directory and called up on the telephone
page 109.
The crosshairs can be moved horizontally and vertically by
turning and pressing the rotary pushbutton. Press the rotary
pushbutton to switch between the horizontal and vertical cross-
hair bars or deactivate this option. Using this option, you can,
for example, select a new destination
page 109.Moving along the route. This function can be used while route
guidance is activated. Turn the rotary pushbutton clock-
wise/anti-clockwise to move the map along the current route.
Altitude display
Note
Did you know that you can choose from four different map types

page 118?
Applies to vehicles: with navigation system
In the driver information system
RETURN
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
Fig. 101 Display when
a lane change is
required
Fig. 102 Display when
a turn-off is required










Navigation 112
After you have entered a destination or a route and have started the
route guidance, the navigation information is displayed in the driver
information system. If you select another function (e.g. radio) using
the multi-function steering wheel, the navigation will briefly be
replaced by the function selected
page 128.
Distance to turn-off
Estimated time of arrival
Total distance to destination/next stopover
Name of motorway, major road or street you are driving on. An
arrow in front of the street name indicates that you are
supposed to turn into the street.
Arrow indicating a turn-off. A necessary lane change before the
turn is also displayed.
Bar graph. If an arrow is displayed, a bar graph will also appear.
The fewer bars are displayed, the shorter the distance to the
turn-off point.
WARNING
The route calculated by the navigation system is a recommenda-
tion of how best to reach a destination. Pay attention to traffic
lights, no stopping signs, lane change restrictions, one-way
streets, etc.
Note
An exclamation mark “!” in front of the street name indicates that
the navigation DVD does not contain all the information on this
street or street section. Pay attention to traffic rules such as one-way
streets or pedestrian zones.
Storing a destination
Applies to vehicles: with navigation system
In the directory (single destination)
A single destination can either be stored as a new entry or
added to an existing entry.
Important: You must have entered a single destination

page 107.
Storing a destination as a new entry
– Press the Memory control button.
– Turn the rotary pushbutton to Store in directory and
press to confirm.
– Turn the rotary pushbutton and select New entry.
– Press the rotary pushbutton. An entry space will now
appear
fig. 103.
– Turn the rotary pushbutton to Surname and press the
rotary pushbutton. The speller will appear on the MMI
display
page 43.
– Enter the surname using the speller.
A1
A2
A3
A4
A5
A6
Fig. 103 Address card











Navigation117
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control
Applies to vehicles: with navigation system
Deleting a route
– Select: Function selector button > control button
Memory > Delete route.
Stored route plans (routes with stopovers) will now be deleted.
Applies to vehicles: with navigation system
Changing a route plan
A route plan (Route with stopover) can be changed, moved, deleted
or set as a destination again. Simply use the rotary pushbutton to
select the destination or a stopover on the route plan and then press
the rotary pushbutton. Then select one of the options displayed.
If you delete the destination, the last stopover will automatically be
set as the new destination.
Applies to vehicles: with navigation system
Route list
– Select: Function selector button > control button
Route > Route list.
The route list is only visible when the route guidance is active and
contains the following information:
•Details of the route
•Distances
•Street names
•Town and place names
Applies to vehicles: with navigation system
Route criteria
– Select: Function selector button > control button
Route > Route criteria.
The route will be calculated according to various criteria.
Dynamic navigation
The dynamic navigation function optimises a route plan by using
the most current traffic reports to automatically recalculate routes
and avoid traffic jams.
If the navigation does not display a detour route, although the
dynamic navigation function is ON and a traffic jam has been
reported on the planned route, this is because the estimated time
required for the detour is longer than the estimated time required
for remaining on the route with the traffic jam.
Route options
The navigation system selects the faster or shorter route.
Motorway / ferry / toll road
If you do not want the navigation system to include motorways,
ferries or toll roads in the route calculation, you can set the option
avoid. However, there can be situations in which you will not be able
to avoid them.
Note
If one of the selected criteria is unavoidable (i.e. the route must
contain the undesired criterion), the system will automatically
calculate the route accordingly.
NAV
NAV
NAV










Navigation119
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control Direction of travel
The map is set to face the direction of travel. If the map scale is
between 50 m and 50 km, the map will rotate according to the direc-
tion of travel.
Auto
If the scale is less than 2.5 km, the map is set to face the direction
of travel. If the scale is more than 2.5 km, the map is set to face
north.
Applies to vehicles: with navigation system
Intersection zoom
– Select: Function selector button > function
selector button > Intersect. zoom.
When the intersection zoom function is activated, any intersection
will be zoomed in on automatically. This provides a detailed view,
giving you a better perspective of the road layout. When zooming,
the map will automatically be set to face the direction of travel.
Applies to vehicles: with navigation system
Map type
– Select: Function selector button > function
selector button > Map type.
Destination
The map shows you the destination. The destination is marked with
a chequered flag. The map is set to face north.
Position
The map depicts the vehicle's current location. The map scale and
map orientation settings are not changed.Overview
The entire route from the starting point to the final destination is
displayed on the map. The map scale varies according to the length
of the route. The map is set to face north.
Current position 3D
The map is shown in a 3D perspective (as seen from the current loca-
tion). The map is set automatically to face the direction of travel

page 118.
Applies to vehicles: with navigation system
Map content
– Select: Function selector button > function
selector button > Map content.
The display of map contents such as motorway exits or restaurants
can be switched on () and off.
Applies to vehicles: with navigation system
Voice guidance
– Select: Function selector button > function
selector button > Voice guidance.
You can switch the voice guidance cues on and off as desired.
Select the setting off (phone) to deactivate the spoken navigation
information only for the duration of a telephone call.
Applies to vehicles: with navigation system
Altitude display
– Select: Function selector button > function
selector button > Altitude display.
NAV
SETUP
NAV
SETUP
NAV
SETUP
NAV
SETUP
NAV
SETUP










Calling up traffic information123
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control
Important: The system must be tuned to a traffic station

page 122, and a navigation DVD must be inserted in the
drive
page 14.
– Press the function selector button marked .
– If the list of traffic messages
page 122, fig. 108 does
not appear in the MMI display, press the function
selector button again. A list of traffic messages

page 122, fig. 108 will now appear in the MMI display.
– Turn the rotary pushbutton to mark an entry.
– Press the rotary pushbutton. Traffic information on the
entry will now be displayed.
– To display the next traffic message in the detail view, turn
the rotary pushbutton to Display next report and press to
confirm.
– To display the selected message on the map in the detail
view, turn the rotary pushbutton to Show report on map.
– Press the rotary pushbutton. The red hatched line shows
the stretch of road affected by the traffic obstruction

fig. 109.– To display the next traffic message on the map, press the
rotary pushbutton again.
When the route guidance is active, the TMC traffic messages which
are relevant for your route are shown with a red warning symbol and
are sorted by distance to your current location
page 122,
fig. 108. A traffic obstruction in the immediate vicinity will be shown
at the top of the list.
All other traffic messages are then shown with greyed-out warning
symbols and are sorted according to road category (motorways,
major roads, other roads) and road number.
Urgent traffic messages such as a car travelling in the wrong direc-
tion on the motorway are automatically displayed in the MMI
display. To cancel the report, simply press the button or
the rotary pushbutton.
When the route guidance is active, traffic messages are shown with
red warning symbols and are sorted according to road category
(motorways, major roads, other roads) and road number.
Other settings
Applies to vehicles: with TP memo timer
TP memo timer
– Select: Function selector button > function
selector button > TP memo timer.
You can set two times of day at which you want the MMI system to
record traffic reports. Use the Timer status option to activate and
deactivate the timers individually or together. You can set the time
by turning the rotary pushbutton to mark the timer and pressing to
confirm. Then turn the rotary pushbutton to change the time.
Switch from hours to minutes by pressing the rotary pushbutton.
Fig. 109 Displaying a
TMC traffic message
on the map
INFO
INFO
A1
RETURN
INFO
SETUP











Basic operation129
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control
•If your vehicle is not equipped with these systems, the corre-
sponding button has no function.
Applies to vehicles: with multi-function steering wheel
Adjusting the volume
The volume of the active audio source (radio, CD, Audi
music interface*, TV*) and the route guidance cues can
be adjusted on the multi-function steering wheel.
Important: The MMI system must be switched on

page 40.
Increasing and reducing the volume on the
active audio source
– Use the right thumbwheel
page 128, fig. 110 to
scroll up/down.
Mute
– To mute the MMI system, scroll the right thumbwheel

page 128, fig. 110 down until a crossed-out loud-
speaker symbol appears in the status line of the MMI
display. Any activated media drives will be paused. Pause
will also appear in the heading of the MMI display.
– To deactivate the mute/pause function, scroll the right
thumbwheel up. Playback of the paused media drive will
then be resumed.
Route guidance
– Press the right thumbwheel
page 128, fig. 110. The
last route guidance cue will now be repeated.
– To change the volume, scroll the right thumbwheel
up/down during the route guidance cue.
Listening to the radio
Applies to vehicles: with multi-function steering wheel
Calling up the radio menu
Important: The radio function on the MMI system must be
switched on
page 54.
– Press the button
page 128, fig. 110 repeatedly
until the radio menu appears in the display of the driver
information system
page 130, fig. 113.
Would you like to find out more about the radio function in your
vehicle? You can find a detailed description on
page 53,
“Listening to the radio”.
Applies to vehicles: with multi-function steering wheel
Setting the waveband
The four wavebands FM, MW, LW and DAB* (digital radio)
are displayed at the top of the display of the driver infor-
mation system.
Important: The radio menu must be displayed
page 130,
fig. 113.
A4
A4
A4
Fig. 112 List of wave-
bands
MODE











Basic operation131
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control Would you like to find out more about the media function in your
vehicle? You can find a detailed description on
page 63, “Playing
media”.
Applies to vehicles: with multi-function steering wheel
Selecting a track
Important: A list of tracks must be displayed
page 130,
fig. 114 /
fig. 115.
– Scroll the left thumbwheel
page 128, fig. 110 to mark a
track.
– Press the left thumbwheel to select the track.
Note
You can select a CD in the CD changer or a folder on a portable
player via the MMI control console
page 12.
Applies to vehicles: with multi-function steering wheel
Pausing and resuming (media drive)
Important: A track must be playing
page 63.– Scroll the right thumbwheel all the way down to pause
the track that is currently playing.
– To continue playback, scroll the right thumbwheel
upwards.
Television
Applies to vehicles: with multi-function steering wheel and TV (analog and analog/digital)
Calling up the TV menu
Important: The TV function on the MMI system must be
switched on
page 71.
– Press the button
page 128, fig. 110 repeatedly
until a list of TV channels appears in the display of the
driver information system.
Would you like to find out more about the TV function in your
vehicle? You can find a detailed description on
page 71,
“ Television”.
Fig. 115 Track list of a
folder
Fig. 116 List of TV
channels
MODE





 




Menus155
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control
•Extract number - to copy a telephone number from a text
message into the display for editing.
•Edit - to edit a text message open in the inbox.
•Forward - to forward a text message you have received to
another telephone number.
Templates
The Templates menu is used to insert a text template (e.g. I will be
late ...) into a text message.
Text message settings
•Status report - to receive a delivery status report from the
message centre after you send a text message.
•Va li dity - to specify how long text messages are held at the
message centre.
•Service centre - to retrieve or change the number of the message
centre.
•Memory capacity - to display the total capacity of the text
message memory and the amount of memory used.
•Store text msg - to store text messages in the outbox when they
are sent. The memory can fill up quickly if you activate this function.
If the memory is full, the crossed-out envelope symbol will appear
in the display and no more text messages can be received.
Delete txt msgs
•Read - to delete read text messages from the inbox.
•Unread - to delete unread text messages from the inbox.
•Sent - to delete text messages you have written and sent.
•Unsent - to delete text messages you have written but not sent.
•Delete all - to delete all text messages on the SIM card.
Note
The handset display shows only text messages which are stored on
the SIM card.
Applies to vehicles: with handset for the car telephone kit
“Settings” menu (handset)
– Press the control button for Menu
page 142,
fig. 126.
– Select Settings using the navigation button.
Switch off tel.
The car telephone kit logs off the GSM network and shuts down but
the handset remains connected. If mobile phones are connected,
these connections are closed.
The car telephone kit can be switched on again from the handset
and will automatically log onto the GSM network.
Fig. 143 Settings
Fig. 144 Ring tone
volume
A8










Speech dialogue system169
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control
Speech dialogue system
Applies to vehicles: with multi-function steering wheel and speech dialogue system
Introduction
You can operate many functions of the MMI quickly and
easily with the speech dialogue system.
Using the speech dialogue system you can conveniently switch
between the various modes, e.g. from radio to CD mode. You can
also access various functions on the radio, the CD changer, the tele-
phone* or the directory by saying commands or calling up previ-
ously stored name tags
page 172. In addition, you can select navi-
gation* destinations and have the system guide you to them, call up
the map display and change the map scale
page 178.
If you do not know a command, no problem! If the speech dialogue
system is activated, simply say HELP. The system will transmit the
commands you can currently say or will help you with a cue

page 171.
The speech dialogue system recognises commands and spoken
numbers regardless of the speaker.
How to help the system understand you
•Speak clearly in a normal volume. Speak louder if you are driving
fast.
•Speak in a normal tone without long pauses.
•Avoid talking while the speech dialogue system is giving a cue.
•Close doors, windows and sun roof* to reduce background
noise. Make sure that passengers are not talking when you say a
command.
•Keep the air outlets of the air distribution system pointed away
from the microphone, which is fitted in the vicinity of the front inte-
rior lights.
•The system should only be operated by the driver, since the
hands-free microphone is directed towards the driver.Unrecognised speech commands
The system acknowledges your commands with a tone signal. If the
system does not recognise a speech command, it will answer with
<Pardon?> and request you to repeat the command. After a third
failed attempt the system will answer with <Cancel> and the
dialogue will be ended.
WARNING
•Please direct your full attention to the road at all times! As the
driver, you have full responsibility for the safety of the vehicle and
other road users. For this reason, you should only use the func-
tions in a manner that allows you to maintain control of the
vehicle in all situations - accident risk!
•The speech control system must not be used in cases of emer-
gency, since the voice changes in stressful situations. This could
result in a failed or delayed telephone connection. Always dial
emergency numbers manually!





!




Speech dialogue system 172
Name tags
Applies to vehicles: with multi-function steering wheel and speech dialogue system
Introduction
You can access entries in the radio, CD and directory func-
tions via previously recorded name tags (spoken entries).
To conveniently tune to radio stations, play CDs or access directory
entries via the speech dialogue system, you must first store so-
called name tags. You can choose any name you like for the name
tags. The name tags are stored in the speech dialogue system.
Applies to vehicles: with multi-function steering wheel and speech dialogue system
Storing a name tag
You can record name tags for radio stations, audio CDs
and directory entries.
Important: The speech dialogue system must be switched
on
page 170.
Name tag for a radio station
– Say the command RADIO. Radio mode will be activated.
– Using the MMI control console
page 55 or the multi-
function steering wheel
page 130, select the radio
station for which you wish to record a name tag.
– Press the talk button . The <beep> tone will sound.
–Say SAVE STATION to record a name tag for the selected
radio station.
– Say the name you wish to store for the name tag.
– Repeat the name again once the speech dialogue system
requests you to do so.Name tag for a CD
– Say the command CD. CD mode will be activated.
– Using the MMI control console, the multi-function
steering wheel or the CD changer, select the CD for which
you wish to record a name tag.
– Press the talk button . The <beep> tone will sound.
–Say SAVE CD to record a name tag for the selected CD.
– Say the name you wish to store for the name tag.
– Repeat the name again once the speech dialogue system
requests you to do so.
Name tag for a directory entry
– Say the command DIRECTORY. The directory will open.
– Using the MMI control console, select the address card
for which you wish to record a name tag.
– Press the talk button . The <beep> tone will sound.
–Say SAVE NAME to record a name tag for the directory
entry that is currently open.
– Say the name you wish to store for the name tag.
– Repeat the name again once the speech dialogue system
requests you to do so.
The recorded name tags do not change the names of the radio
stations, CDs or directory data shown in the MMI display and the
driver information system.
The recorded names can only be assigned, called up
page 173
and deleted
page 173 using the speech dialogue system. Each
main mode has different commands that can be used in conjunction
with the recorded name tags
page 172.