AUDI R8 2008 1.G Infotainment MMI Operating Manual

139 Telephone handset





 




Basic operation 140
Basic operation
Applies to vehicles: with handset for the car telephone kit
Switching the handset on and off
Switching on and off automatically
– Make sure that the handset is properly engaged in the
carrier.
– Switch on the ignition. The handset is switched on auto-
matically when the MMI is switched on. The connection
to the car telephone kit is established.
– Remove the ignition key. The handset is switched off
automatically when the shutdown delay time has
elapsed.
Switching on manually
– Switch on the ignition.
– Press and hold the on/off button
fig. 124 until the
start screen
fig. 123 appears. The handset is ready for
operation as soon as a Bluetooth connection has been
established.Switching off manually
– Press and hold the on/off button
fig. 124 until the
screen goes out.
Caution
You must switch off the telephone system in areas where the use of
mobile telephones is prohibited. Please observe all relevant caution
notices and regulations.
Note
•If you need to bond the handset again, you will find further infor-
mation on
page 27.
•If a valid SIM card is not detected when you switch on the
handset, Please insert the SIM card will appear on the display

page 31.
Applies to vehicles: with handset for the car telephone kit
Overview of the keypad
Fig. 123 Start screen
of handset
A7
A7
Fig. 124 Overview of
keypad










Basic operation141
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control Left control button
Selects the function shown in the bottom left-hand corner of the
display, e.g. Ph.book
page 140, fig. 124.
Right control button
Selects the function shown in the bottom right-hand corner of the
display, e.g. Menu
page 140, fig. 124.
“End call” button
Ends a call, declines a call or closes a menu.
Navigation button
The top or bottom part of the navigation button can be used to scroll
up or down within a menu shown on the display.
The left or right side of the navigation button can be used to select
one of the main menus
page 151 (Last calls
page 152), adjust
settings (e.g. brightness
page 155) or to move the cursor when
entering text
page 143.
“Call” button
Dials a number or receives a call. Also displays a list of numbers
dialled when pressed in the main screen. Numeric keypad
The numeric keypad is used to enter the numbers 0 - 9, as well as
letters and special characters. The and buttons are used for
different purposes in various functions
page 143.
If the automatic keypad lock is activated
page 156, the buttons on
the handset keypad will be locked automatically (approximately one
minute after you take it out of the carrier) and a padlock symbol

page 142, fig. 127 will appear in the handset display.
To unlock the keypad, press the control button for Unlock on the
handset and immediately press the button.
To activate the keypad lock manually, press the button on the
handset and immediately press the control button for Lock.
To receive a call when the keypad lock is active, press the control
button for Answer. The keypad will be locked again automatically
when you end or decline a call.
On/off button
Switches the handset on or off
page 140.
Volume control button
You can increase or reduce the earpiece volume during a phone
call.
Fig. 125 Volume
control button
A1
A2
A3
A4
A5
A6
*#
A9
*
*
A7
A8










Basic operation 142
Display
Applies to vehicles: with handset for the car telephone kit
Information in the display
Various symbols provide the user with information in the
main screen.
The table below describes the symbols shown in illustrations

fig. 126 and
fig. 127:
Fig. 126 Information in
display
Fig. 127 Information in
display
SymbolExplanation
Signal strength of the GSM network at your cur-
rent location
Battery level
Symbol for an existing Bluetooth connection
Symbol for an incoming text message
Roaming symbol
Symbol for a missed call
Function for left control button
Function for right control button
Symbol for keypad lock activated
Symbol for text message memory full
Mobile network service provider
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11











Basic operation143
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control
Applies to vehicles: with handset for the car telephone kit
Entering a text message
Text messages can be entered using the conventional
method or with automatic word recognition (T9).
Entering text (normal method)
–If T9 mode is active
fig. 128, keep pressing the
button until the T9 symbol disappears.
– To enter a text at the position indicated by the cursor,
press one of the buttons marked to
page 140,
fig. 124.
– Keep pressing each button until the desired character
appears in the display.
– For example, press the button once to enter the
letter m.
– Press the button quickly a second time to enter
the letter n.
– With each additional press of the button the
next character assigned to the button is selected.– If you do not press a button again within about one
second, the character is entered and the cursor will flash
at the next position; you can then enter the next char-
acter.
– To enter a special character, hold down the “*” button
and select the character.
– To move the cursor to the left, right, up or down, press
the left, right, top or bottom part of the navigation
button.
– To insert a space, press the button.
– To delete the character to the left of the cursor, select
Delete.
Entering text using automatic word recognition
(T9)
– If T9 mode is not active
fig. 128, keep pressing the
button until the T9 symbol appears.
– Press one of the buttons marked to to start
entering a word.
– Press each button only once for each letter of the word,
even if the exact letter desired does not appear in the
display. The letters you enter are displayed on a grey
background
fig. 128.
– Enter all the letters of the word.
– If the dictionary contains more than one suggested word,
press the button to choose between the different
suggestions. A message, e.g.
fig. 128 appears in
the handset display.
– Press the button if the word in the display is correct.
Fig. 128 Symbols for
entering text
A1#
19
6mno
6mno
6mno
0
A1
#
29
A3
*
A4
0





 




Basic operation 144
– To enter a special character, hold down the “*” button
and select the character.
– To move the cursor to the left, right, up or down, press
the left, right, top or bottom part of the navigation
button.
– To insert a space, press the button.
– To delete the character to the left of the cursor, select
Delete.
While you are entering the text, you can use the button to switch
between normal text entry, text entry with automatic word recogni-
tion (T9) and upper/lower case letters.
Entering text (normal method)
When you press a button, the available characters appear briefly at
the bottom of the display. The available characters depend on which
language is selected for input.
If you are entering a text in letter mode and want to enter a number,
hold down the button for the desired number.
Entering text using automatic word recognition (T9)
The handset attempts to recognise each word you enter.
If several words corresponding to the letters you have entered are
available in the dictionary, you can browse through the available
words using the “*” button. For example, 1/4 in the display

page 143, fig. 128 shows the number of suggested words avail-
able. In the above example, the figure “4” shows the number of
words available for the string of letters entered. The figure “1” is an
orientation aid to help you choose from the list of suggested words.
If a word is not in the dictionary, you can select the control button
for Options and use the Add word function. Type in the word using
the normal method and select Store. The word appears in the text
message and is added to the dictionary.The table below describes the symbols shown in the illustration

page 143, fig. 128:
0
#
A3
SymbolExplanation
Automatic word recognition T9 is active.
Amount of space still available in the text message
(in characters).
The suggested word (e.g. Audi) is highlighted on a
grey background until you finish the entry.
Index number (e.g. “1”) of the suggested word
shown in the display (for orientation purposes) and
total number of suggested words (e.g. “4”).
Upper/lower case setting
A1
A2
A3
A4
A5










Using the telephone145
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control
Using the telephone
Applies to vehicles: with handset for the car telephone kit
Placing calls
Placing calls
– Enter the desired number on the keypad.
– If you have entered an incorrect digit, press the control
button for Delete.
– Press the “Call” button
page 140, fig. 124 to start
dialling.
Selecting a number from the “phone book”
– Press the control button for Ph.book
page 142,
fig. 126. The entries stored in the phone book will be
listed.
– To jump to a particular entry in the phone book, enter the
initial letter using the normal text entry method.
– Use the navigation button to scroll up or down to the
desired entry
page 153, fig. 140.– Press the “Call” button
page 140, fig. 124 to start
dialling.
Redial
– Press the “Call” button
page 140, fig. 124 once. The
list of last numbers dialled appears.
– Use the navigation button to scroll up or down to the
desired entry
page 153, fig. 140.
– Press the “Call” button to start dialling.
Hold the reverse side of the handset to your ear (the earpiece and
microphone are located on the reverse side of the handset

fig. 129).
You can use the handset to make phone calls in private mode or
handsfree mode
page 150.
A microphone integrated in the interior light is used in handsfree
mode. The microphone is directed towards the driver.
You can also select and dial a telephone number from the call lists

page 152.
Note
Press and hold the button to enter the international network
symbol “+”.
Fig. 129 Earpiece and
microphone on back
A5
A5
A5
A1A2
*+










Using the telephone 146
Applies to vehicles: with handset for the car telephone kit
Speed and one-touch dialling
The position number of a SIM card entry is used for speed
dialling and one-touch dialling.
Dialling a SIM card entry (speed dialling)
– Enter the position (e.g. 2)
fig. 130 of the SIM card entry
you want to dial.
– Press the button. The selected SIM card entry is
displayed.
– Press the “Call” button
page 140, fig. 124 to start
dialling.
Dialling a SIM card entry (one-touch dialling)
– Press and hold one of the buttons 2 to 9. The selected
SIM card entry will be displayed.
–Confirm the Really connect? prompt by pressing the
control button for Ye s. The number will be dialled.Dialling the mailbox (one-touch dialling)
– Press and hold button . The phone number you have
stored for your mailbox will be dialled
page 157.
Changing the position of a SIM card entry
– Press the control button for Ph.book. The phone book
entries will be listed
page 153, fig. 140.
– To jump to a particular entry in the phone book, enter the
initial letter using the normal text entry method.
– To select a SIM card entry, use the navigation button to
scroll up or down.
– Press the control button for Ok.
– Select Edit and then press the control button for Ok. You
can now change the information stored in the selected
SIM card entry.
–Scroll to the Position function
fig. 130 using the navi-
gation button.
– Press the control button for Ok.
– To delete the position shown on the display, press the
control button for Delete.
– Enter the desired position on the keypad.
– Press the control button for Ok.
–Scroll to the Store function using the navigation button.
– Press the control button for Ok to save the changes you
have made.
The telephone numbers stored at positions two to nine in the SIM
card phone book can also be used as one-touch dial numbers.
Fig. 130 Position of a
phone book entry
#
A5
1





!




Using the telephone147
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control Your mailbox number is assigned to one-touch dial button . If you
haven't already stored a mailbox number
page 157, you will have
the opportunity do this when you select one-touch dial button .
The second telephone number stored in the SIM card phone book
(position number “2”) is assigned to one-touch dial button .
The next seven telephone numbers in the SIM card phone book are
assigned to buttons to respectively.
Note
•If a position is already assigned, it must be deleted before you
can store a new entry at that position.
•How many position numbers are stored depends on the SIM card
being used.
Applies to vehicles: with handset for the car telephone kit
Answering and ignoring telephone
calls
Answering telephone calls
– Press the control button for Answer, or
– Press the “Call” button
page 140, fig. 124.Ignoring telephone calls
– Press the control button for Reject, or
– Press the “End call” button
page 140, fig. 124.
Depending on whether the caller is stored in the phone book and
whether the number is transmitted with the call, the name, the tele-
phone number or Unknown will appear on the MMI display.
If you activate the Answer on eject function, an incoming call will be
answered immediately when you take the handset out of the carrier

page 156.
Applies to vehicles: with handset for the car telephone kit
Emergency calls
Without SIM card
– Switch on the ignition, the MMI and (if not already acti-
vated) the handset
page 140. A Bluetooth connection
must exist between the handset and the car telephone
kit. Please insert the SIM card should be shown in the
handset display.
– Press the control button for SOS
fig. 132.
1
1
2abc
3def9wxyz
Fig. 131 Incoming call
A5
A3
Fig. 132 Control
button SOS










Using the telephone 148
– When the message Do you really wish to connect to the
emergency number? appears in the handset display,
confirm with Ye s. The emergency number will be dialled.
With SIM card and PIN entered
– Switch on the ignition, the MMI and (if not already acti-
vated) the handset
page 140. A Bluetooth connection
must exist between the handset and the car telephone
kit, and a SIM card must be in the handset.
– If necessary, press the “End call” button to display the
main screen
page 142, fig. 126.
– Enter the emergency number (e.g. 112).
– Press the “Call” button
page 140, fig. 124 to start
dialling.
WARNING
Since your telephone operates via radio waves, a connection
cannot be guaranteed under all circumstances. Do not rely solely
on your telephone when a vital communication (e.g. medical emer-
gency) is involved.
Note
•You can also dial an emergency number on the MMI
page 89.
•Always follow the directions of the emergency operators when
making an emergency call. Do not end the call before you are
requested to do so. Otherwise, this could result in life-saving infor-
mation not being passed on.
•Emergency numbers are not the same for all countries. Please
familiarise yourself with the correct emergency numbers in advance
when travelling in foreign countries or regions where the numbers
may be different.
Applies to vehicles: with handset for the car telephone kit
Ending calls
– To end an active call or stop dialling a number, press the
control button for End call
fig. 133, or
– Press the “End call” button
page 140, fig. 124.
If you placed a call on hold earlier on, that call will remain on hold.
Use the Resume function to continue the call.
If a menu is open in the handset display, the menu will be closed the
first time you press the “End call” button. The active call is discon-
nected when you press the “End call” button again.
A7
Fig. 133 Active call
A3