AUDI S4 2000 B5 / 1.G 01E Transmission Final Drive Pinion And Ring Gear Adjustment Owner's Manual

1) run at least 50 km (30 miles)
Pa
ge 21 of 38 Drive
pinion and rin
g gear, ad
justin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM03.39.19

39-162

Performing check measurement

Checking dimension "r"

- Turn drive pinion at least 5 turns in both
directions.

- Insert universal mandrel and perform check measurement.
If the shims have been correctly selected, the dial gauge should now
show the value of "r" as marked on the ring gear, reading anti-
clockwise in the red scale, within a tolerance of 0.04 mm.

- Peen drive pinion nut with a punch.
Pa
ge 22 of 38 Drive
pinion and rin
g gear, ad
justin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM03.39.19

39-163

Ring gear, adjusting

(Adjusting differential)
Repairs after which the ring gear has to be
adjusted Page 39
-150
, Adjustment overview

Note:

Differential tapered roller bearings are low
friction bearings. Therefore the friction torque
only has a limited use as a check. Correct
adjustment is only possible by determining the
total shim thickness "S
total
."

Do not additionally oil new tapered roller
bearings for friction torque measurement. The
bearings have already been treated with a
special oil by the manufacturer.

Determining total shim thickness "S
total
" for
shims "S1" + "S2"
(Setting preload of tapered roller bearing for
differential)

Drive pinion removed or ring gear dismantled
from differential housing

- Pull out drive flange oil seal with lever.
Pa
ge 23 of 38 Drive
pinion and rin
g gear, ad
justin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM03.39.19

- Remove differential tapered roller bearing outer
races and take out shims Page 39
-120
.
Pa
ge 24 of 38 Drive
pinion and rin
g gear, ad
justin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM03.39.19

39-164
Press outer race of left tapered roller bearing for
differential (housing side) with shim "S2" into
housing
Fig. 2 , Page 39
-126
. To perform
measurement use a shim "S2*" with a thickness
of 1.00 mm (one 0.80 mm shim and one 0.20
mm shim).

Note:
For measurement purposes a shim "S2" of 1.0
mm is initially inserted which will be designated
"S2*" in the following. After determining the
backlash "S2*" will be replaced by the correct
"S2.."

- Press in
outer race
of right
tapered
roller
bearing
for
differential
(final drive
cover
side)
without
shims
Fig. 8 , Page 39
-
120
(install as far as
Pa
ge 25 of 38 Drive
pinion and rin
g gear, ad
justin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM03.39.19

the stop).

- Insert differential into housing. Ring gear is
positioned on right side (cover side).

- Fit cover and tighten bolts to 25 Nm.

- Install special tools VW 521/4 and 521/8 onto housing side in
differential housing.
- Turn cover side of differential housing upward.
Pa
ge 26 of 38 Drive
pinion and rin
g gear, ad
justin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM03.39.19

39-165

- Turn differential 5 turns in both directions to
settle tapered roller bearing.

- Place measuring plate VW 385/17 onto
differential.

- Fit measuring tools.
A - Dial gauge extension approx. 30 mm long
B - Hex bolt M8 x 45
- Place D.T.I. extension on center of measuring plate VW 385/17.
- Set dial gauge (3 mm measuring range) to "0" with 2 mm preload.

Note:
If the measurement has to be repeated, the differential must again be
turned 5 turns in each direction to settle the tapered roller bearing. - Lift differential without turning; read play on dial gauge and note.
Measurement in following example: 0.50 mm
Pa
ge 27 of 38 Drive
pinion and rin
g gear, ad
justin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM03.39.19

39-166

Formula:
"S
total
"
=
"S2*" + measurement + bearing
preload

Example:

Inserted shim(s) "S2*" 1.00
mm
+ Measured value 0.50
mm
+ Bearing preload (constant) 0.30
mm
= Total shim thickness "S
total
" for shims
"S1" + "S2"
1.80
mm
Pa
ge 28 of 38 Drive
pinion and rin
g gear, ad
justin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM03.39.19

39-167

Determining thickness of shim "S1*"

Note:

The preliminary adjustment shim "S1*" will be
replaced with the final shim "S1" after
determining the backlash.
The total shim thickness "S
total
" remains
unchanged.

Formula:
"S1*"
=
"S
total
" - "S2*"

Example:


Total shim thickness "S
total
" for shims
"S1" + "S2"
1.80
mm
- Inserted shim(s) "S2*" 1.00
mm
= Thickness of shim "S1*" 0.80
mm

- Determine shim(s) as accurately as possible
from table Page 39
-172
.
Pa
ge 29 of 38 Drive
pinion and rin
g gear, ad
justin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM03.39.19

39-168

Measuring friction torque (check)

Drive pinion removed
Differential fitted with shims "S1*" and "S2*"

Friction torque specifications: 1) run at least 50 km (30 miles)
Note: - Fit torque gauge 0-600 Ncm -A- onto differential.
- Read friction torque.New bearings
Used bearings
1)
150-300 Ncm 30-60 Ncm
Differential tapered roller bearings are low friction bearings. Therefore
the friction torque only has a limited use as a check. Correct
adjustment is only possible by determining the total shim thickness
"S
total
."
Do not additionally oil new tapered roller bearings for friction torque
measurement. The bearings have already been treated with a special
oil by the manufacturer. If the final drive set (drive pinion and ring gear) is being re-adjusted,
the adjustment of the drive pinion should be performed now, and the
Pa
ge 30 of 38 Drive
pinion and rin
g gear, ad
justin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM03.39.19