tires AUDI S7 2015 Service Manual

Page 272 of 316

2 70 T ire s and wheel s
through or over such obstacles can damage
your tires. Impact with a curb may also
cause damage to your tires.
- After any impact, immediately inspect your
tires or have them inspected by the nearest
authorized Audi dealer. Rep lace a damaged
t ire as soon as possible.
- Inspect your t ires every 2,000 miles (3,000
km) for damage and wear . Damage is not al­
ways easy to see. Damage can lead to loss of air and underinflation, wh ich could eventu­
ally cause t ire failu re. If you bel ieve that a
t ire may have been damaged, replace the
t ire as soon as possible.
- These tires may wear more quickly than oth­
ers.
- Please also remember that, while these t ires
deliver respons ive handling, they may ride
less comfortably and make mo re no ise than
othe r cho ices .
Reduced performance in winter /co ld
season condition s
All tires are des igned for certain pu rposes.
The low aspect ratio, ultra high pe rformance
tires orig inally installed on your veh icle are in­
tended for maximum dry and wet road per­
formance and handling. They are not suitable for cold, snowy or icy weather conditions. If
you dr ive under those circumstances, you
should equip your vehicle with all-season or
winter tires, which offer better traction under
those cond it ions. We suggest you use the rec­
ommended snow or a ll-season tires specified
for your vehi cle, or their equ ivalent.
Refer to¢
page 267 for more deta iled infor­
mat ion regarding winter tires.
Tire pressure
monitoring system
U) General notes
Each t ire, includ ing the spare (if provided),
should be checked monthly when cold and in­
flated to the inflation pressure recommended by the vehicle manufacture r on the vehicle
p lacard or tire inflation pressure label. (If your vehicle has tires of a diffe
rent size than the
size indicated on the vehicle placard or tire in­
flat ion pressure labe l, you shou ld determ ine
the proper t ire inflation pressure for those
t ires).
As an added safety feature, your ve hicle has
been equipped with a tire pressure monitoring
system (TPMS) that illum inates a low tire
pressure telltale when one or more of your
t ires is significantly under-inflated. According­
ly, when the low tire pressure telltale illumi­
nates, you shou ld stop and check you r tires as
soon as possib le, and inflate them to the
proper p ressu re. Driving on a sig nifican tly u n­
der- inflated t ire causes the tire to overheat
and can lead to tire fai lure . Under-inflation al­
so reduces fuel efficiency and tire tread life,
and may affect the vehicle 's hand ling and
stopp ing ability.
Please note that the TPMS is not a substitute
for proper tire maintenance, and it is the driv­ er's respons ibility to maintain correct tire
pressure, even if under-inflation has not
reached the level to trigger illumination of the
TPMS low tire pressure telltale .
Your vehicle has also been equipped with a
TPMS malfunction indicator to ind icate when
the system is not operating properly. The
TPMS ma lfunction indicator is combined w ith
the low tire pressure telltale . When the sys­
tem detects a malfunction, the telltale will
flash fo r approxima te ly one m inute and then
rema in continuously illum ina ted. This se­
quence will continue upon subsequent vehicle
start-ups as long as the malfunction exists.
When the malfunction indica to r is illum inat­
ed, the system m ay not be ab le to detect or
signal low tire pressure as intended . TPMS
malfunctions may occur for a var iety of rea­
sons, incl uding the insta llation of replace­
ment or alternate tires or wheels on the vehi­
cle that prevent the TPMS from functioning
properly. Always check the TPMS malfunction
telltale after replacing one or more tires or
whee ls on you r vehicle to ensu re that the re­
placement o r alternate ti res and wheels a llow
the TPM S to cont inue to func tion p roperly.

Page 273 of 316

M N <( I.J "". rl I.O
"' rl
"' rl
Tire pressure indicator appears
The tire pressure indicator in the instrument
cluster informs you if the tire pressure is too
low or if there is a system malfunction.
Fig. 205 Display: underinflation warning
Fig. 206 Display: System malfunction
Using the ABS sensors, the tire pressure moni­
toring system compares the tire tread circum­ ference and vibration characteristics of the in­
dividual tires. If the pressure decreases in one
or more tires, this is indicated in the instru­
ment cluster with a warning symbol
rD] and a
message
c:> fig . 205.
The tire pressure monitoring system must be
reset via MMI each time the pressures are ad­
justed (e.g. when switching between partial
and fu ll load pressure) or after changing or re­
placing a tire on your vehicle
c:> page272 . The
TPMS indicator only monitors the tire pres­
sure that you have previously stored. You can
find the recommended tire pressures for your
vehicle on the label on driver's side 8-pillar
c:>page247.
Tire tread circumference and vibration charac­
teristics can change and cause a tire pressure
warning if:
- the tire pressure in one or more tires is too
low,
Tires and wheels 2 71
- the tire has structural damage,
- the tire pressure was changed, wheels rotat-
ed or replaced but the TPMS was not reset
c:>poge272.
- the spare tire* is mounted .
Warning symbols
[I] Loss of pressure in at least one tire¢.& .
Check the tire or tires and replace or repair if
necessary. The indicator light
rD] in the instru­
ment cluster also illuminates <=:>
page 12.
Check/correct the pressures of all four tires
and resetTPMS via MMI.
l!I (Tire Pressure Mon itoring System) Tire
pressure! System malfunction .
Ifljl appears
after switching the ignition on or while driving
¢
fig. 206 and the indicator light rD] in the in­
strument cluster blinks for approximately one
minute and then stays on, there is a system
malfunction. Attempt to store the correct tire
pressure
c:> page 272. If the indicator light
does not turn off or if it turns on shortly
thereafter, immediately drive your vehicle to
an authorized Audi dealer or authorized repair
facility to have the malfunction corrected.
_& WARNING
- If the tire pressure indicator appears in
the instrument cluster display, one or
more of your tires is significantly under­
inflated. Reduce your speed immediately
and avoid any hard steering or braking
maneuvers. Stop as soon as possible and
check the tires and their pressures. In­
flate the tire pressure to the proper pres­
sure as indicated on the vehicle's tire
pressure label<=:>
page 247 . Driving on a
significantly under-inflated tire causes
the tire to overheat and can lead to tire
failure. Under-inflation also is likely to
impair the vehicle's handling and stop­
ping ability.
- The driver is responsible for maintaining
the correct tire pressures. You must check the tire pressures regularly.
.

Page 274 of 316

272 Tires and wheels -Under certain conditions (such as a spor­
ty driving style, winter conditions or un­
paved roads), the pressure monitor
indicator may be delayed.
- Ask your authorized Audi dealer if run­
flat tires may be used on your vehicle.
- The tire pressure monitoring system may
stop working when there is an ESC mal­
function.
- Using snow chains may result in a system
malfunction.
- The tire pressure monitoring system on
your Audi was developed using tires with
the "AO" or "RO" identification on the
tire sidewall
c:> page 260. We recom­
mend using these tires.
Reset tire pressure monitoring system
If the tire pressure is adjusted, wheels are ro­
tated or changed, the TPMS must be reset via
MMI.
• Before storing the new tire pressures, check
that the current pressures on all four tires correspond to the specified values and
adapt the pressures to the current load <=>page 247.
• Switch on the ignition.
• Select in the MMI: !CAR !function button>
(Car)* systems control button > Servicing &
checks > Tire pressure monitoring > Store
tire pressures> Yes, store now.
Do not store the tire pressure if there are
snow chains on the tire. Otherwise, a sys­
tem malfunction may occur.

Page 278 of 316

276 What do I do n ow ?
After changing a wheel
A wheel change is no t complete without the
doing the following .
.. Always store the vehicle tool kit, the jack*
and the replaced tire in the luggage com­
partment ¢
page 134.
.. Check the tire pre ssur e on the spare wheel
immediately after mount ing it .
.,. As soon as possible, have the
tightening
torqu es
on all wheel bol ts checked with a
torq ue wrench. The correct tightening tor ­
que is 90 ft lb (120 Nm) .
.. Have the flat tire
replaced as soon as possi­
ble.
@ Tips
- If you notice t hat the wheel bolts are
corroded and difficult to t urn while
changing a t ire, they should be replaced
before you check the tighten ing torque.
- Drive at reduced speed unt il you have the
tightening torques checked .
- After changing a wheel, the tire pressure
i n a ll four tires must be checked/correct­
ed and the tire pressure mon itor ing indi­
cator must be stored in the MMI
¢ page 272 .
Decorative wheel covers
Applies to vehicles: with decorative wheel covers
T he decora tive wheel covers must be removed
first to access the wheel bolts .
Fig. 210 Cha nging a w hee l: Remov ing t he w heel cove r
Removing
.,. Inse rt the hook (prov ided with the veh icle
tool kit) in t he hole in the wheel hub cove r. ..
Pull off the
de cora tive wheel co ver
¢ fig . 210.
Wheels with wheel bolt caps
Applies to veh icles: w it h w heel bolts with caps
The caps must be removed first from the
wheel bolts before the bolts can be un­
screwed.
Fi g. 211 Cha ng ing a whee l: re m oving t he w hee l b o lt
caps
Removing
.. Push the plastic clip (provided with t he veh i­
cle tool k it) over the wheel bo lt cap until the
inner retainers on the clip align w ith the
edge of the cover.
.,. Remove the cap with the
plastic clip (vehicle
tool kit)
i=> fig . 211 .
Refitting
.. Place the caps over the whee l bolts and
push them back on.
The caps are to protect and keep the wheel bolts clean .

Page 281 of 316

M N <( I.J -<I'. rl I.O
"' rl
"' rl
Taking the wheel off/installing the spare
Follow these instructions step-by-step for
changing the wheel.
Fig. 216 Changing a wheel: using the screwdriver han­
dle (with the blade removed} to turn the bo lts
F ig . 2 17 Changing a wheel: alignment pin ins ide the
top hole
After you have loosened a ll wheel bolts and
ra ised the veh icle off the ground, remove and
replace the wheel as follows:
R emoving the wheel
.. Use the hex agon al so ck et in th e screw driv­
e r handle
to comp letely remove the top­
most wheel bo lt and set it aside on a
clean
s u rface ¢fig. 216.
.. Screw the threaded end of the alignm ent
pin from the tool k it hand -tight into the
empty bolt hole
¢fig. 217.
.. Then remove the other wheel bo lts as de­
scribed above .
.. Take off the wheel leav ing the alignment pin
in the bolt hole
¢ (D.
Putting on the spar e wheel
.. Lift the spare wheel and carefully slide it
over the alignment pin to guide it in place
¢(D.
What do I d o now ? 2 79
.. Use the hexagonal socket in the screwdriver
handle to screw in and tighten all wheel
bolts
slightly.
.. Remove the alignment pin and insert and
tighten the remaining wheel bolt slightly like the rest.
.. Turn the jack handle counter-clockwise to
lower the veh icle until the jack is fully re­
leased .
.. Use the wheel bo lt wrench to tighten all
wheel bo lts f irm ly
¢page 277. Tighten
them
crosswise, from one bolt to the (ap­
proximately) opposite one, to keep the
wheel centered.
(D Note
When removing or installing the whee l,
the rim could hit the brake rotor and dam­
age the rotor. Work carefu lly and have a
second person help you.
@ Tips
Neve r use the hexagonal socket in the han ­
dle of the screwdriver to loosen or tighten
the w heel bo lts.
- Pull the reversible blade from the screw­
dr iver before you use the hexagonal
socket in the hand le to turn the wheel
bolts.
- When mount ing tires w ith
unidi rectional
tread design
make sure the tread pat­
tern is po inted the right way
~page 280.
-The wheel bo lts shou ld be clean and easy
to turn. Check for dirt and corrosion on
the mating surfaces of both the wheel
and the hub. Remove all d irt from these
surfaces before remounting the whee l.

Page 282 of 316

28 0 What do I do no w?
Tires with unidirectional tread design
Tires with unidirectional tread design must be
mounted with their tread pattern pointed in the right direction .
Using a sp are t ire wi th a tread pattern
int ended fo r use in a specific dir ect ion
When us ing a spare tire w ith a tread patte rn
intended for use in a specific direction, please
note the following:
- The direction of rotation is marked by an ar­
row on the side of the tire.
- If the spare t ire has to be installed in the in­
correct direction, use the spare tire only
temporarily since the t ire will not be able to
achieve its optimum performance character­
ist ics with rega rd to aquaplaning, noise and
wea r.
- We recommend that you pay particular at­
tent ion to this fact du ring wet weather and
that you adjust your speed to matc h road
conditions.
- Replace the flat tire w ith a new one and
have it installed on your vehicle as soon as
possible to restore the handling advantages
of a unidirectiona l tire .
Notes on wheel changing
Please read the information c> page 260 , New
t ires and replacing tires and wheels
if you are
going to use a spare tire which is different
from the tires on your vehicle .
After you change a tire :
-Che ck the tire p re ssure on the sp are imme ­
di ately afte r in st a llat ion.
- Ha ve th e wh eel b olt tightenin g torque
che ck e d w ith a torque wrench as soon a s
possible b y you r autho rized Aud i de aler o r
a qu alified ser vice station .
- With ste el and alloy wheel rims , the wheel
bolts are cor rectl y tightened at a torque of
90 ft lb (1 20 Nm ).
- If yo u notice that the wheel bolt s are cor­
r oded a nd d iffi cult to tu rn while changi ng
a t ire, the y should be replaced before you
check the t ightening torq ue. -
Re pl ac e the flat ti re with a new one and
h av e it in st a lled on you r vehicle as soon as
po ssible. Remount th e wheel cov er.
Un til then , driv e with ex tra c are a nd at re­
duc ed sp ee ds.
A WARNING
-
- If you are going to equ ip your vehicle
with tires or rims which differ from those
which were factory installed, then be
sure to read the information
9 page 260,
New tires and replacing tires and
wheels .
-Always make sure the damaged wheel or
even a flat tire and the jack and tool kit
are properly secured in the luggage com­
pa rtment and are not loose in the pas­
senger compartment.
- I n an accident or sudden maneuver they
could fly forwa rd, injuring anyone in the
veh icle.
- Always sto re damaged wheel, jack and
too ls securely in the luggage compart­
ment. Otherwise, in an accident or su d­
den maneuve r they could f ly forward,
causing injury to passengers in the ve hi­
cle.

Page 291 of 316

M N <( I.J "". rl I.O
"'
@ Tips
Check carefully to make sure the hook-up
is secure before moving the car up the flat­
bed truck ramp .
Vehicle transport
Whenever you hov e your vehicle transported,
be sure to note the following :
(D Note
Mount the tie-down chains/cables over the
running surface (circumference) of the
tires. Never secure the vehicle by the axle,
the suspension struts or the front or rear
towline eye . For technical reasons, the
pressure in the suspension struts may
change du ring the transport and this will
adve rsely affect vehicle handling.
Lifting vehicle
Lifting with workshop hoist and with
floor jack
The vehicle may onl y be li~ed at the lif ting
points illu stra ted.
Fi g. 2 29 Front l ift ing po int
Fig. 2 30 Rea r lifti ng poin t
:;:; N 0 6 ., a,
5 .. Read and heed WARNING Q ,&..
Emergenc y situ ation s 289
.. Activate the vehicle jack mode* in the MM I:
!CAR I function button > (C ar)* s ystem s con­
trol button>
S e rv ic ing & check s> Air su sp. :
jack m ode> On .
.. Locate lifting poin ts Q fig . 229 and
Q fig . 230 .
.. Adjust lifting arms of wo rkshop hoist or
floor jack to match veh icle lifting points.
.. Insert a rubber pad be tween the floor jack/
workshop hoist and the lift ing po in ts.
The vehicle jack mode* must be activated so
that the automat ic adjustment of the Adap­
tive Ai r Suspens ion* does not make it more
diffi cult to raise the vehicle with the floor
jack.
If yo u must lift your v ehi cle with a floor jack
t o wo rk und ern eath , be sure th e vehicle i s
s af ely s upported on s tands intended for thi s
purpo se.
Front lifting point
The lifting po int is located on the floor pan re­
inforcement abo ut at the same leve l as the
jac k mounting point
Q fig. 229. Do n ot lift
t h e ve hicle at th e verti cal sill reinforc em ent .
Re ar lifting point
The lifting point is located on the vert ical rein­
forcement of the lower sill for the on-boa rd
ja ck
c::> fig. 230 .
Lifting with vehicle j ack
Re fer to Q page 277 .
A WARNING
-To reduce the risk of ser ious injury and
veh icle damage .
- Always lift the veh icle only at the spe ­
cia l workshop hoist and floor jack lift
po ints illust rated
c::> fig . 229 and
c::> fig . 230.
- Failu re to lift the vehicle at these
po ints could cause the vehicle to tilt or
fall from a lift if there is a change in ve­
hicle weight distribution and balance .
This might happen, for example, when
-

Page 298 of 316

29 6 Con sum er Inf ormation
-Always make sure the transmission se­
lector lever (automatic transmiss ion) is
in P (Park position) and the park brake is
applied .
@) For the sake of the environment
-Changing the engine settings wi ll ad­
versely affect em iss ion levels. This is det­
rimental to the environment and increas­
es fuel consumption .
- Always observe env ironmental regula­
tions when dispos ing of old engine oil,
used brake fluid, dirty engine coolant,
spent batteries or worn out tires.
- Undeployed airbag modules and preten­
s ioners might be classified as Perchlo ­
rate Material -spec ial handling may ap­
ply, see www.dtsc.ca .gov/hazardous­
waste/perch lorate . When the veh icle or
parts of the restraint system including
airbag modules safety belts wit h preten ­
sioners are scrapped, all applicable laws
and regulations must be observed. Your
authori zed Aud i dea ler is familiar with
these requirements and we recommend
that you have your dealer perform this
serv ice for you .
Additional accessories,
modifications and
parts replacement
Additional accessories and parts
replacement
Always consult an authorized Audi dealer be­
fore purchasing accessories.
Your veh icle incorporates the latest safety de­
sig n featu res ensu ring a high standard of ac­
tive and passive safety .
This safety could be compromised by non-ap­ proved changes to the veh icle. For this reason ,
if pa rts have to be replaced , please observe
the following points when install ing addition­
a l accessories: Approved Audi accessories and genuine Aud
i
parts are available from authorized A udi deal­
ers.
T hese dea le rs a lso have the necessary facili­
ties, tools and trained specialists to install the parts and acc essories proper ly .
A WARNING
-Using the wrong spare parts or using non-
approved accessories can cause damage to
the veh icle and ser ious persona l injury.
- Use on ly accessories express ly approved
by Audi and gen uine Audi spare parts
- These parts and accessories have been
specia lly designed to be used on yo ur ve­
h icle .
- Never install accessor ies such as tele­
phone crad les or beverage ho lders on a ir­
bag covers or within the airbag deploy­
ment zones . Do ing so will increase the
risk of injury if a irbags are triggered in an
accident!
- Before you check anything in the engine
compa rtment, always read and heed a ll
WARNI NGS
9 page 225 .
(D Note
-If items other than genu ine Audi spare
parts, add-on equipment and accessory
items are used or if repair work is not
performed accord ing to specified meth­
ods, this c an resu lt in seve re damage to
your vehicle's eng ine and body (such as
corrosion) and adversely affect yo ur vehi ­
cle's warranty .
- If emergency repairs must be performed
elsewhere, have the vehicle examined by
an authorized A udi dealer as soon as
possible .
- The manufacturer cannot be held liable
for damage wh ich occ urs due to failure
to comply with these stipu lations.

Page 301 of 316

A
A/C (automatic climate control) .... .. .. 72
A/C (climate control) . . . . . . . . . . . . . . . . . 70
Accessories .. ............. .... .. .. . 296
Active lane assist . . . . . . . . . . . . . . . . . . . . 95
Activating and deactiva ting . .. .. .. .. .. 96
C leaning the camera area ... ... .. .. . 2 13
Descript ion ...... ..... ... ... ... .... 95
Instrument cluster indicator light . . . . . 96
Messages . . . . . . . . . . . . . . . . . . . . . . . . . 96
Notes on instrument cluster display . . . . 96
Sett ing the steering wheel vibrat ion .. .. 97
Adaptive a ir s uspension/sport . ... .. .. . 102
Adapt ive cruise control . . . . . . . . . . . . . . . . 86
C lea ning the sensor ....... .. .. .. .. . 213
Messages . . . . . . . . . . . . . . . . . . . . . . . . . 93
Request for driver intervention . ... .. .. 91
Stop-and-go traffic .... ... .. .. .. .. .. 90
Adapt ive Lig ht (defective) ... .. .. .. .. .. 22
AdBlue .. .. .. ................. .. ... 221
F il ling . .. .. ................. .. ... 223
Messages in the instrument cluster dis -
play . .. .. .. .. ........ ... .. ... ... . 222
Adding Eng ine coolant ........... .... .. .. . 232
Eng ine oil .. .. ........... .. .. .. ... 229
W indshield washer fluid ....... ... .. 238
Addit ives
Eng ine oi l .. ............. .... .. ... 229
Adj usti ng
A ir dist ribution (au toma tic climate con-
trol) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
air distribution (cl imate control) ... .. .. 70
Front seats . . . . . . . . . . . . . . . . . . . . . . . . 53
Instrument illum inat ion ... .. .. .. .. .. 47
Steer ing colum n elec trically .. .. .. .. .. 75
Steer ing colum n manually . .. .. .. .. .. 75
Temperature (automat ic climate co ntrol) 73
Temperature (climate control) .. ... ... 70
Airbag system . . . . . . . . . . . . . . . . . 147, 168
Advanced Airbag System ... .. .. .. .. . 151
Advanced Airbag System components . 155
Care ...... ... ................ .... 163
M N Chi ld ren ... ... .. .. ...... .. .. .. .. . 175 <(
~ Chi ld restra ints ........... .. .. .. ... 175
~ Components (front airbags) .. .. .. .. . 155 1.1"1 ,...., 1.1"1 ,....,
Inde x 299
Danger of fitting a ch ild seat on the front
passenger seat ..... . ... ...... ... .. 149

Disposa l .. .. .. .. .. . .. ... .... ... .. 163 •
Front a irbags . . . . . . . . . . . . . . . . 151, 153
How do the front airbags work? .... .. 157
How many a irbags does my vehicle
have? .. .. .. .. .. .. . .. .... .... .... 155
How the Advanced Airbag System com-
ponents work togethe r ......... .... 15 7
Impo rtant sa fe ty instru ctions on the
knee airbag sys tem ... .. .... ... .. .. 166
Important t hings to know .... ... .. .. 147
Knee airbags ... .... . ... ...... ... .. 164
Monitoring .. .. .. ................. 159
PASSENGER AIR BAG OFF light ..... .. 160
Repairs ... .. .. .. .... ............. 163
Safety instructions .. .............. . 162
S ide a irbags ... .. .. . .. .... .... .. .. 166
S ide curtain airbags . ... ..... ... .... 169
Warning/ind icator lights ........ .. .. . 19
Warning/Indicato r lights ....... .. .. 159
When must the system be inspected? 159
A ircraft
Transpo rting your vehicle 289
A lcantara
Cleaning .. .. .. .. ................. 215
A ll-wheel drive .. .... . ... ...... ... .. 200
Winter tires ..... .. . .. .. ..... ... .. 267
Alternator . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Amb ience lighting . ................. . 47
Anti -freeze
refer to Engine coolant . ..... ... .. .. 231
Anti- lock b raking system ............ . 195
Warning/ind icator lights ........ .. .. . 19
Anti-slip regu lation .. ........... .... 195
Warning/ind icator lights .. .. ... ... .. . 19
Anti-theft systems Electronic immobi lizer ....... ... .. .. . 32
Asht ray .... .. .. .. .. . ............... 59
Audi braking guard
refer to brak ing guard ............. .. 86
Audi drive select
refer to drive select ... ............. 102
A udi Se rv ice Repair Manuals and Liter a-
tu re .. ... .. .. .... .. . .. ... .... ... .. 294

Page 302 of 316

300 Index
AUTO automatic climat e control .. .. ... ... ..
73
Automatic headlights ....... .. .... .. 44
climate control . . . . . . . . . . . . . . . . . . . . . 70
Auto Lock . . . . . . . . . . . . . . . . . . . . . . . . . . 3 3
Automatic belt retractor .. ... ..... .. .
141
Automatic climate control
Air vents . .... ........... .... .... ..
7 3
Automatic recirculation .... .. .. .. .. . . 74
Opera tion . . . . . . . . . . . . . . . . . . . . . . . . . 72
Setup . .. .. ................ ... .. .. 74
synchron izing .... ......... ... .. .. .. 73
Automatic Shift Lock (ASL) .... .. .. .. . 110
Automatic transmission ..... .. .. .. .. . 109
Automatic Shift Lock (ASL) .......... 110
Driving . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Emergency mode . . . . . . . . . . . . . . . . . . 114
Emergency release .......... .. .... . 115
Kick-down ............... .. .. .... . 113
Manual shift program ..... .... .... . 113
Selector lever . . . . . . . . . . . . . . . . . . . . . 109
Automatic wipers .................. .. 48
Auto Safety Hotline ........ .. .. .. .. . 136
Ave rage consumption ....... .. .. .. .. . . 25
Average speed . . . . . . . . . . . . . . . . . . . . . . .
25
Avoid damaging the vehicle .. .. .. .. .. . 204
B
Brake fluid
Changing the brake fluid ............
234
Checking the brake fluid level ........ 234
What is the correct brake fluid level? .. 234
What should I do if the brake fluid warn-
ing light comes on? ................
234
Brake system
Anti- lock braking system . . . . . . . . . . . . .
19
Brake assist system . ....... .... .. .. 195
Brake booster .. ... .............. .. 199
Brake fluid .. .. .. .......... ...... . 234
Brake fluid specifications for refill and re-
placement ...... ................ .
234
Brake pads .... .. ............. .... 203
Electromechanical parking brake ... .. . 79
Fluid reservoir ... ................ . 234
How does moisture or road salt affect the
brakes? . . . . . . . . . . . . . . . . . . . . . . . . . .
198
Warning/indicator lights ........ .. .. . 15
Worn brake pads symbol . . . . . . . . . . . . . 20
braking guard
Settings .. .... .. .. .............. ..
93
Brak ing guard . .. .. .......... ...... .. 86
Messages ... .. .. .. ....... .... .... . 93
Break-in period .. .. ............. .... 203
Brake pads .. ... . ... ... .... ... .. .. 203
Tires ........ ... .. .............. . 203
Bulbs .......... .. .. .............. . 284
Bag hooks . . . . . . . . . . . . . . . . . . . . . . . . . . 67 C
Battery ..... ................ ..... .
Charging ................... ..... .
Important warnings ...... .. .. .. .. .
Jump starting . .... ....... .. .. .. .. .
Location
. .. .... ........... .. .... .
low ..... .. ................ ... ' . .
Replacing the battery ..... .. .. .. .. .
State of charge ........... .. .. .. .. .
w· t · 1n er operation ......... .... .... .
Working on the battery .... .. .. .... .
Before driving .............. ... .. .. .
235
237
235
285
235
201
238
201
235
235
128
Blended gasoline . . . . . . . . . . . . . . . . . . . 217
Blower (automatic climate control) . . . . . . 73
Blower (climate con trol) . . . . . . . . . . . . . . . 70
Booster seats .............. ... .... . 182
California Proposition 65 Warning ..... 226
Battery specific .. ............. .... 236
Capacities .. .. .. .. ............. .. .. 292
Engine oil ..... .. ............. .... 227
Carbon par ts
Cleaning . . . . . . . . . . . . . . . . . . . .
214,215
Car carrier
Transporting your vehicle ....... ....
289
Care ..... .. .. .. .. .... ......... .... 212
Cargo area ...... .. .. ... ........... . 134
Cargo net . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Catalytic converter . ... .. ... ..... .. .. 204
Center armrest
Cockpit . .. .. .. .. ............. .. .. .
56
Central locking .... ............. ..... 33
Emergency locking ................ ..
37

Page:   < prev 1-10 ... 11-20 21-30 31-40 41-50 51-60 next >