wheel size AUDI S7 2015 Owners Manual

M N <( (.J
'SI: ,...., \!) ..,.,
,...., ..,., ,....,
U.S. Federal Standard if a child with elec­
trical capac itance greater than the com­
bined capacitance of a typical one-year
old infant restra ined in one of the for­
ward fac ing or rearward-fac ing ch ild
seats w ith which your vehicle was certi­
fied is on the front passenger seat and
the other conditions for airbag deploy­ ment are met.
- Acc ident statist ics have shown that chil­
dren are generally safer in the rea r seat
area than in the front seating posit ion .
- For their own safety, all children, espe­
c ially 12 years and younger, sho uld al­
ways ride in the back p roperly rest rained
for their age an d size .
Advanced front airbag system
Your veh icle is equipped w ith a front Advanced
Airbag System in comp liance with Un ited
States Federal Motor Vehicle Safety Standard 208 as applicable at the time your vehicle was
manufactured.
The front Advanced Airbag System supple­ ments the safety belts to provide add it iona l
protection for the driver's and front passeng­
e r's heads and upper bodies in frontal crashes.
The airbags inflate only in frontal impacts
when the vehicle dece le rat io n is high enough.
The front Advanced A irbag System for the
fro nt seat occupants is not a substitute for
your safety belts . Rather, it is part of the over­
all occupant rest raint system in your ve hicle.
A lways remember that the airbag system can
only help to pro tect you, if you are s itting up ­
righ t, wearing yo ur sa fety belt and wearing it
properly. This is why you and yo ur passengers
must always be properly restrained, not just
because the law requires you to be.
The Advanced Airbag System in your veh icle
h as been certified to meet the " low r isk" re­
q uir ements for 3 and 6 year-o ld children on
the passenger s ide and very small adu lts on
the dr iver side. The low risk deployment crite­
ria are intended to he lp reduce the risk of i n­
j ury through interaction with the front airbag
A irbag system 153
that can occur, for examp le, by being too
close to the steering wheel and instr ument
panel when the airbag inflates .
In add ition, the system has been cert ified to
comply with the "s uppression" requirements
of the Safety Standard, to turn off the front
airbag for in fants 12 months o ld and younger
who are rest rained on the front passenger
seat in child restraints that are listed in the
Standa rd
c> page 175, Child restraints and
Advanced front airbag system .
"Suppression" requires the front a irbag on the
passenger side to be turned off if:
- a child up to abo ut one year of age is re­
strained on the front passenger seat in one
of the rear-fac ing or forward -facing infant
restraints listed in Federal Motor Vehicle
Safety Standard 208 with which the Ad ­
vanced Airbag System in your ve hicle was
cert ified . Fo r a listing of the chi ld restraints
that were used to certify you r vehicle's com­
p lia nce w it h t he US Safe ty Stand ard
c>page 175,
-When a pe rson is detec ted o n the front pas ­
senge r seat that has an e lec trica l capa ci­
tance t hat is more than the tota l elect rical
capacitance of a child that is about 1 year
old restrained in one of the rear-facing or
forward-facing infant restraints (listed in Federal Motor Vehicle Safety Standard 208
w ith which the Advanced A irbag System in
your vehicle was certified), the front airbag
on t he passenger side may or may not de­
ploy.
The
PASSENG ER AIR BAG OFF light comes on
when the electron ic cont ro l unit de tects a to ­
ta l elect rical capac itance on the front passen­
ger seat that requi res the front a irbag to be
turned off. If the
PASSENGER AIR BAG OFF
li gh t does no t come on, the front airbag on
the passenger side has not been turned off by
the contro l unit and can deploy if the control
u nit senses an impact that meets the condi­
tions stored in its memory.
If the total e lectr ica l capacitance registered
on the front passenger seat is more than that
ll>
•
•

196 Intellig ent technolog y
distance detected to the veh icle a head is too
smal l.
Anti -slip regulation (ASR )
ASR reduces engine power when the drive
wheels begin to spin and adapts the force to
the road condit ions. This makes it eas ier to
start, accelerate and drive up hills.
Electronic differential lock (EDL )
The ED L brakes wheels that are spinn ing and
transfers the d rive power to the other wheels.
This f unct ion is not availab le at h igher speeds.
In extreme cases, EDL automat ically switches
off to help keep the brake on the braked whee l
from overheating. EDL w ill switch on aga in au­
tomatically when conditions have returned to norma l.
St eering recommendat ion
The ESC helps to stabilize the vehicle by
cha nging the steering to rque.
In vehicles with dynam ic steering*, ESC also
helps to stabilize the steering in critical s itua­
tions .
Select ive w heel to rque control
Selective wheel torque control is used when
driving on curves . The front wheel on the in­
side of the curve or both wheels on the inside
of the curve are braked selectively as needed.
This a llows more prec ise driving in curves. The
applicable system may not activate when d riv­
ing i n wet or snowy conditions.
.&_ WARNING
- T he ESC and its integrated systems can­
not overcome the limits posed by natural physical laws
. This is especially impor­
tant on slippery or wet roads. If the sys­ tems beg in acting to stabilize your vehi­
cle, you should immediately change your
speed to match the road and traffic con­
d itions . Do not let the increased safety
p rovided by these systems tempt you to
take risks. Do ing so will increase the ri sk
of a loss of veh icle cont ro l, collision and
serio us personal inj uries.
- Always adapt your speed to road, traffic
and weather conditions . The risk of los ­
ing control of the vehicle increases when
driving too fast , especially through
curves and on slippery or wet roads, and
when dr iv ing too close to vehicles up
ahead . The ESC and its integrated sys­
tems cannot a lways prevent collisions -
there is still a risk of acc idents!
- Always accelerate with special care on
even, smooth su rfaces such as those that
are wet or covered with ice and snow .
The drive wheels can spin even w ith
these assistance systems that c annot al­
ways he lp to red uce the risk of loss of ve­
h icle control.
(D Tips
- ABS and ASR only wo rk correctly when
all four wheels are equipped wi th iden ti­
cal tires. D ifferen t tire sizes can lead to a
reduction in engine power.
- Yo u may hear noises when the systems
descr ibed are workin g.
-If the ind icator light DJ or Ea (USA
mode ls)/ lCO j <Canada models) appears,
there may be a malfunction~
page 19,
<=>page 19.

M N <( (.J
'SI: ,...., \!) ..,.,
,...., ..,., ,....,
Winter t ire s
When driving in the w inter, your vehicle w ith
all-wheel drive has an advantage, even with
regular tires. In winter road conditions it may
be advisable to mount winter tires (or all-sea­
son tires) for improved driveability and brak­ ing: these tires must be mounted on
a ll fo ur
wheels .
See also c:> page 267, Winter tires.
Tire chain s
Where tire cha ins are mandatory on certain
roads, th is normally a lso applies to vehicles
with all-wheel drive
c> page 268, Snow
chains.
Re placing wh eels/ tire s
Vehicles w ith all-wheel drive must a lways
have tires of the same size. Also avoid tires
with different tread depths. For details see
page
c:> page 260, New tires and replacing
tires and wheels .
Off-Road dri ving ?
Your Audi does not have enough ground clear­
ance to be used as an off-road vehicle. It is
therefore best to avoid rough tracks and un­
even terrain as much as possible. Also refer to
c:>page204.
A WARNING
Always adjust your driving to road and traf­
fic condit ions . Do not let the extra safety
afforded by all-wheel dr ive tempt you into
taking extra risks.
- Although the all-wheel dr ive is very ef­
fec tive, a lways remember that braking
capacity is limited by t ire traction. Yo u
should therefore not dr ive at excessive
speeds on icy or slippery road surfaces.
- On wet road surfaces, be careful not to
drive too fast because the front wheels cou ld begin to slide on top of the water
(aquaplaning). If this sho uld occur, you
will have no warning from a sudden in­
crease in engine speed as with a front­
wheel drive vehicle. A lways drive at
speeds wh ich are suited to the road con­
ditions -risk of c rash.
Int ellig ent technolog y 201
Energy management
Starting ability is optimized
Energy management controls the distribution
of electrical energy and thus optimizes the
availability of electrical energy for starting the engine.
If a vehicle with a conventional energy system
is not d riven for a long per iod of t ime, the bat­
tery is discharged by idling current consumers (e .g. immobilize r). In certain circumstances it
can resu lt in the re be ing insuffic ient energy
available to start the engine.
Intelligent energy management in your vehi­
cl e ha ndles the distribution of e lectr ica l ene r­
gy. Start ing ability is markedly improved and
the life of the battery is extended .
Bas ica lly, energy management consists of
ba tter y dia gno sis, id lin g curr ent manage­
ment
and dynamic ener gy manag ement.
Battery di agnos is
Battery diagnosis continuously determ ines
the state of the batte ry . Sensors determine
battery voltage, battery current and battery
tempe rature. This de termines the curren t
state of cha rge and the power of the battery .
Idling current management
Idling current management reduces energy
consumption while the vehicle is standing .
With the ign ition switched off, it controls the
energy supply to the various electrica l compo ­
nents. Da ta fr om ba ttery d iagnos is is cons id ­
ered.
Depend ing on the batte ry's state of cha rge,
individ ual cons ume rs a re g radually turned off
to prevent excessive discharge o f the battery
and th us maintain star ting capability.
Dynamic energy management
While the vehicle is being dr iven, dynamic e n­
ergy ma nagement distr ibutes the energy gen­
erated a ccord ing to the needs of the individ u-
al components . It regulates consumpt ion, so
that more e lectrical energy is not being used .,.
•
•

M N <( (.J
'SI: ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
Bead
means the part of the tire that
is made of steel wires, wrapped
or reinforced by ply cords and
that is shaped to fit the rim .
Bead separation
means a breakdown of the bond
between components in the
bead.
Cord
means the strands forming the
plies in the tire.
Cold tire inflation pressure
means the tire pressure recom­
mended by the vehicle manu­
facturer for a tire of a designat­
ed size that has not been driven
for more than a couple of miles (kilometers) at low speeds in
the three hour period before
the tire pressure is measured or
adjusted.
Curb weight
means the weight of a motor
vehicle with standard equip­
ment including the maximum
capacity of fuel, oil, and cool­
ant, air conditioning and addi­
tional weight of optional equip­
ment.
Tires and wheels 243
Extra load tire
means a tire design to operate
at higher loads and at higher inflation pressures than the
corresponding standard tire .
Extra load tires may be identi­
fied as "XL", "xl", "EXTRA
LOAD", or "RF" on the sidewall.
Gross Axle Weight Rating ("GAWR")
means the load-carrying capaci­
ty of a single axle system,
measured at the tire-ground in­
terfaces.
Gross Vehicle Weight Rating ("GVWR")
means the maximum total
loaded weight of the vehicle .
Groove
means the space between two
adjacent tread ribs.
Load rating (code)
means the maximum load that
a tire is rated to carry for a giv­
en inflation pressure. You may
not find this information on all
tires because it is not required by law.
•
•
'

Recommended inflation
pressure
see¢ page 243J Cold tire infla­
tion pressure.
Reinforced tire
means a tire design to operate
at higher loads and at higher
inflation pressures than the
corresponding standard tire. Reinforced tires may be identi­
fied as "XL", "xl", "EXTRA
LOAD", or "RF" on the sidewall.
Rim
means a metal support for a
tire or a tire and tube assembly
upon which the tire beads are
seated.
Rim diameter
means nominal diameter of the
bead seat. If you change your
wheel size, you will have to pur­ chase new tires to match the
new rim diameter.
Rim size designation
means rim diameter and width.
Rim width
means nominal distance be­
~ tween rim flanges.
<( (.J
'SI: ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
Tires and wheels 245
Sidewall
means that portion of a tire be­
tween the tread and bead.
Speed rating (letter code)
means the speed at which a tire
is designed to be driven for ex­
tended periods of time. The rat­ ings range from 93 mph (150
km/h) to 186 mph (298 km/h)
¢ page 263. You may not find
this information on all tires be­ cause it is not required by law.
The speed rating letter code,
where applicable, is molded on
the tire sidewall and indicates
the maximum permissible road speeds ¢
A in Winter tires on
page
267.
Tire pressure monitoring system
means a system that detects
when one or more of a vehicle's tires are underinflated and illu­
minates a low tire pressure
warning telltale.
Tread
means that portion of a tire
that comes into contact with
the road.
•
•
'

M N <( (.J
'SI: ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
If you wish to improve comfort
when operating the vehicle at normal load (up to 2/3* occu­
pants), you can adjust tire
pressures to those specified
for normal vehicle load. Before
operating the vehicle at maxi­ mum load, you must increase
the tire pressures to those
specified for maximum vehicle load
c> .&. .
Bear in mind that the tire pres­
sure monitoring system can on­
ly monitor the tire pressures
you have stored. The system does not recognize the load
condition of your vehicle.
The effectiveness of the tire pressure monitoring system
will be impaired if you store normal load pressures but then
operate the vehicle at its maxi­
mum load
c> .&. .
Tires and wheels 249
See the illustration c> fig. 200
for the location of the label on
driver's side B-pillar (color of
the actual label and exact loca­
tion on the vehicle will vary slightly).
Note that the following table is
accurate at the time of going to
press and is subject to change.
In the event of discrepancies,
the tire pressure label is locat­ ed on the driver's side B-pillar
always takes precedence.
The table below lists the rec­ ommended cold tire inflation pressures for the Audi model
covered by your Owner's Litera­
ture at the vehicle's capacity
weight and the tire sizes instal­
led on the respective models as
original equipment , or as a fac-
tory option. ..,.
•
•
'

250 Tires and wheels
Model/ Tire designation Tire pressure
Engine normal load condition
full load condition
fronta> reara>
front rear
PSI kPA PSI kPA PSI kPA PSI kPA
A7: 235/55 Rl 7 99Y
32 220 29 200 35 240
38 260 3.0 liter High Performance
6-cylinder
255/45 R18 99H
All Season
32 220 29 200 35 240 38 260
255/45 Rl8 99Y 32 220 29 200
35 240
38 260
High Performance
255/40 R19 lOOH XL
35 240 32 220 38 260 280 All Season 41
255/40 Rl9 lOOY
XL
36 250 32 220 38 260 41 280 High Performance
265/35 R20 99H XL
35 240
32 220 38 260 41
280 All Season
265/35 R20 99Y XL
36 250 32 220 38 260 41
280 High Performance
57: 255/40 R19 lOOY XL
39 270
33 230
42 290 42 290 4.0 liter High Performance
a-cylinder 265/35 R20 99Y XL
High Performance
41 280 35 240 44 300 44 300
XL= reinforced or extra load tire. It may also appear as xl, EXTRA LOAD, or RF on the tire side-
wall.
a) normal load
condition¢ page 247.
The correct tire pressure for the
spare wheel is located on a la­
bel on the driver's side B-pillar.
Because technical changes may
be made to vehicle equipment
during the model year, always
compare the tire size designa­
tion on the tire pressure label
on your vehicle with the tires on
your vehicle. Make sure that the
tire size information on the ve­
hicle label is the same as the
size of the tires on the vehicle. This is especially important if
the vehicle belongs to someone
else or you bought the vehicle
with different rims/tires or you bought the vehicle as a previ­
ously owned vehicle.
Remember, your safety and
that of your passengers also de­
pends on making sure that load
limits are not exceeded. Vehicle
load includes everybody and ev­
erything in and on the vehicle.
These load limits are

M N <( (.J
'SI: ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
Driving style
Driving fast around curves,
heavy acceleration and hard
braking increase tire wear.
Rotating tires for more even
wear
For all four tires on your vehicle
to have the same service life,
we recommend that the front
and rear tires are rotated ac­
cording to the tire manufactur­
er's suggested tire rotation in­
tervals. Please remember the
following:
-Tire rotation intervals may dif­ fer from the vehicle service in­tervals outlined in your War­ranty
& Maintenance booklet .
-The longer one tire is used in one location on the vehicle,
the more it wears at certain points; therefore, we recom­
mend that you follow the tire
manufacturer's suggested tire
rotation intervals.
-Vehicles with front-wheel drive experience more tread
wear on the front wheels com­
pared to all-wheel drive (quat­
tro).
-Please rotate ti res as shown
¢ fig. 203.
Tires and wheels 259
-Extra care must be taken when rotating direction-specific
tires ¢ page
280.
Wheel balancing
The wheels on new vehicles are
balanced. However, various sit­
uations during everyday driving
can cause them to become un­ balanced, resulting in vibra­
tions you can usually feel
through the steering wheel.
Unbalanced wheels must be re­
balanced to avoid excessive
wear on steering, suspension
and tires. A wheel must also be rebalanced when a new tire is
installed.
Incorrect wheel alignment
Incorrect wheel alignment can
cause excessive tire wear, im­pairing the safety of the vehi­
cle. If tires show excessive
wear, have the wheel alignment checked by an authorized Audi
dealer or qualified workshop.
All-wheel drive
Vehicles with quattro must al­
ways have tires of the same size, construction and tread
type . For details see
¢ page
200.
•
•
'

Tires and wheels 265
sure of their "previous histo-and sudden deflation and •
ry." Old used tires may have loss of control. • '
been damaged even though -Temperature grades apply
the damage cannot be seen to tires that are properly in-
that can lead to sudden tire flated and not over or un-
failure and loss of vehicle derinflated.
control. -For technical reasons it is
-All four wheels must be fit- not always possible to use
ted with radial tires of the wheels from other vehicles -
same type , size (rolling cir-
in some cases not even
cumference) and the same wheels from the same vehi-
tread pattern. Driving with cle model.
different tires reduces vehi- -If you install wheel trim
cle handling and can lead to discs on the vehicle wheels,
a loss of control. make sure that the air flow
-If the spare tire is not the to the brakes is not blocked.
same as the tires that are Reduced airflow to the
mounted on the vehicle - for brakes can them to over-
example with winter tires - heat, increasing stopping
only use the spare tire for a distances and causing a col-
short period of time and lision.
drive with extra ca re. Refit -Run flat tires may only be
the normal road wheel as used on vehicles that were
soon as safely possible. equipped with them at the
-Never drive faster than the factory. The vehicle must
maximum speed for which have a chassis designed for
the tires on your vehicle are run flat tires. Incorrect use
rated because tires that are of run flat tires can lead to
driven faster than their rat- vehicle damage or acci-
ed speed can fail suddenly. dents. Check with an au-
M -Overloading tires cause heat thorized Audi dealer or tire N <(
build-up, sudden tire fail- specialist to see if your vehi-(.J
'SI: ,....,
ure, including a blowout cle can be equipped with ... \!) 1.1'1 ,...., 1.1'1 ,....,

M N <( (.J
'SI: ,...., \!) 1.1"1 ,...., 1.1"1 ,....,
Sustained high temperature can cause the
materia l of the tire to degenerate and reduce
tire life, and excessive temperature can lead
to sudden tire failure<=>,& .
The grade C corresponds to a level of per form­
ance which a ll passenger car tires must meet
under the Federa l Motor Veh icle Safety Stand­
ard No. 109. Grades Band A represent higher levels of performance on the laboratory test
wheel than the m inimum required by law.
_&. WARNING
The traction grade assigned to this t ire is
based on stra ight-ahead b raking t raction
tests, and does not include acceleration,
cornering, hydrop lan ing o r peak traction
character istics .
_&. WARNING
The temperature grade for this t ire is es­
tablished for a ti re that is properly inflated
and not overloaded . Excessive speed, un­
derinflation, or excessive loading, either
separately or in combination, can cause
heat buildup and possible tire fa ilure.
Winter tires
Winter tires can improve vehicle handling on
snow and ice. At temperatures below 45 °F
(7 °C) we recommend changing to winter
tires .
In some heavy snow areas, loca l governments
may require true winter or "snow" tires, those
with very deeply cut tread. These tires shou ld
only be used in pa irs and be installed on all
four wheels. Make sure you pu rchase snow
tires that are the same size and const ruct ion
type as t he other tires on your ve hicle.
Your veh icle is equipped w ith all -wheel drive,
this will improve tract io n during w inte r dr iv­
in g, even with the standard tires. Howeve r, we
strongly recommend that you a lways eq uip a ll
four whee ls o n your ve hicle with correctly fit­
ted winter tires or all -season tires, when w in ­
ter road conditions a re expected. This also im-
Tire s an d wheel s 267
proves the veh icle's b rak ing performance and
reduces stopping dista nces.
Summe r ti res prov ide les s gr ip on i ce and
snow.
Winter tires (snow tires) must always be fitted
o n all fo ur whee ls.
Ask your authorized Audi dealer or qualified
workshop for permitted winter tire sizes. Use
o nl y rad ial winter t ires.
Winter tires lose their effectiveness whe n the
tread is worn down to a depth of0 .157 inch
(4 mm) .
Only drive w ith w inter t ires under w inter con­
dit ions. Summer t ires handle better when
there is no snow or ice on the roads and the
temperature is above 45 °F (7 °() .
If you have a flat tire, see notes on replace­
ment wheel¢
page 260 .
Please always remember that winter tires may
have a lower speed rating t han the tires o rigi­
nally installed on your vehicle at the time it
was manufactured. P lease see¢
page 263,
Speed rating (letter code)
for a listing of the
speed rating le tter codes and the max imum
speed at which the tires can be d rive n.
The speed rating letter code(¢
page 245) is
o n the side wall of the tire ¢
page 260.
_&. WARNING
Winter t ires have maximum speed limits
that may b e lower than yo ur vehicle's max­
imum speed. Always know the max imum
speed before dr iv ing off. Never dr ive faster
than the speed permitted for yo ur spe cific
win ter tires . This wi ll ca use damage to the
tires leading to an accident and ser ious
personal injury to you and your passen­
gers.
_&. WARNING
Driving faster than the maximum speed
for which the winter tires on your ve hicle
were designed can cause t ire failure in­
cluding a blowout and sudden d eflation,
-
•
•