coolant temperature AUDI TT 1995 8N / 1.G ATW Engine Oxygen Sensor Control Workshop Manual
Page 2 of 37
24-72
Test requirements:
Exhaust system free of leaks.
Coolant Temperature at least 80 C.
Test sequence
- Connect VAS5051 tester or VAG1551 scan tool
and select control module for engine electronics
using "address word" 01 Page 01
-10
. Engine
must run at idle.
Rapid data transfer
HELP
Select function XX
When indicated on display
- Press buttons -0- and -4- to select "Initiate basic setting" and press -Q-
button to confirm input.
Basic Settin
g
Q
Enter displa
y group number XXX
When indicated on display
Note: - Press buttons -0-, -3- and -0- to select "display group number 030" and
press -Q- button to confirm input.
- Check specified value in display field 1.
Increase engine speed to obtain specified values faster. "Oxygen sensor status" indicates status of oxygen sensor control and
oxygen sensors.
Pa
ge 2 of 37 Ox
yg
en sensor control, checkin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.2
Page 13 of 37
24-83
Oxygen sensor aging (oxygen sensor
before catalytic converter), checking
Special tools and equipment
VAG1788/10 RPM adjuster
or
Test requirement:
VAS5051 with VAG5051/1VAG1551 with VAG1551/3ACoolant Temperature at least 80 C.
Pa
ge 13 of 37 Ox
yg
en sensor control, checkin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.2
Page 19 of 37
24-89
Test requirements:
Road test performed and DTC memory
erased.
Coolant Temperature at least 80 C.
Test sequence
- Connect VAS5051 tester or VAG1551 scan tool
and select control module for engine electronics
using "address word" 01 Page 01
-10
. Engine
must run at idle.
Rapid data transfer
HELP
Select function XX
When indicated on display
Note:
During basic setting, the Evaporative Emission (EVAP) canister purge
regulator valve (EVAP valve -N80-) is closed and the A/C compressor is
switched off - Press buttons -0- and -4- to select "Initiate basic setting" and press -Q-
button to confirm input.
Basic Settin
g
Q
Enter displa
y group number XXX
When indicated on display
- Press buttons -0-, -3- and -4- to select "display group number 034" and
press -Q- button to confirm input.
Pa
ge 19 of 37 Ox
yg
en sensor control, checkin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.2
Page 30 of 37
24-100
Test requirements:
Coolant Temperature at least 80 C.
Fuse for oxygen sensor heating OK
Electrical Wiring Diagrams, Troubleshooting &
Component Locations
Test sequence
or
Note:
Coolant reservoir screws must be removed and coolant reservoir must be
placed to side in order to access the harness connector. The coolant
hoses can remain connected. - Disconnect 4-pin harness connector -2- (black) to Heated Oxygen
Sensor (HO2S) -G39- before catalytic converter.
- Disconnect 4-pin harness connector -1- (brown) to Oxygen Sensor
(O2S) behind Three Way Catalytic Converter (TWC) -G130-.
Pa
ge 30 of 37 Ox
yg
en sensor control, checkin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.2