BMW 2 SERIES COUPE 2018 Owners Manual

Adjusting
distance
Safety
information WARNING
The system does not relieve from perj
sonal responsibility. Due to the system limits, braking can be late. There is a risk of accidentsor risk of damage to property. Be aware to thetraffic situation at all times. Adjust the distance
to the traffic and weather conditions and mainj
tain the prescribed safety distance, possibly by
braking.'

Distance displayThe system has been interrupted or
distance control is temporarily supj
pressed because the accelerator
pedal is being pressed; a vehicle
was not detected.Distance control is temporarily supj
pressed because the accelerator
pedal is being pressed; a vehicle
was detected.
Detected
vehicle
Symbol lights up orange:
A vehicle has been detected ahead of
you.
Rolling bars: the detected vehicle has driven
away.
ACC does not accelerate. To accelerate, actij
vate ACC by briefly stepping on the acceleraj
tor pedal or pressing the RES button or the rocker switch.
Indicator/warning
lights Symbol flashes orange:
The conditions are not adequate for
the system to work.
The system was deactivated but applies the brakes until you actively resume control by
pressing on the brake pedal or accelerator
pedal.
Symbol flashes red and a signal
sounds:
Brake and make an evasive maneuver,
if necessary.
System
limits
Detection
range
The detection capacity of the system and the
automatic braking capacity are limited.
Two-wheeled vehicles driving ahead of you for instance might not be detected.
Deceleration The system does not decelerate when a stajtionary obstacle is located in the same lane,
e.g., a vehicle at a red traffic light or at the end
of traffic congestion.
The system also does not react in the followj
ing situations:
'yFor pedestrians or similarly slow-moving
road users.'yFor red traffic lights.'yStationary objects.'yFor cross traffic.'yFor oncoming traffic.Seite 152ControlsDriving
comfort152
Online Edition for Part no. 01402981270 - VI/17

Swerving
vehicles
A vehicle driving in front of you is not detecteduntil it is completely within the same lane as
your vehicle.
If a vehicle driving ahead of you suddenly
swerves into your lane, the system may not be able to automatically restore the selected disj
tance. It may not be possible to restore the sej
lected distance in certain situations, including if you are driving significantly faster than vehijcles driving ahead of you, for instance when
rapidly approaching a truck. When a vehicle
driving ahead of you is reliably detected, the
system requests that the driver intervene by
braking and carrying out evasive maneuvers, if
needed.
Unexpected
lane
change
If a vehicle ahead of you unexpectedly moves
into another lane from behind a stopped vehij
cle, you yourself must react, as the system does not react to stopped vehicles.
Cornering
If the desired speed is too high for a curve, the
speed is reduced slightly, although curves canj not be anticipated in advance. Therefore, drive
into a curve at an appropriate speed.
The system has a limited detection range. Sitj uations can arise in tight curves where a vehij
cle driving ahead will not be detected or will be
detected very late.
When you approach a curve the system may briefly report vehicles in the next lane due to
the bend of the curve. If the system decelerj
ates you may compensate it by briefly accelerj
ating.
After releasing the accelerator pedal the sysj tem is reactivated and controls speed indej
pendently.
Driving
away In some situations, the vehicle cannot drive off
automatically; for example:
'yOn steep inclines.'yFrom bumps in the road.
In these cases, step on the accelerator pedal.
Seite 153Driving
comfortControls153
Online Edition for Part no. 01402981270 - VI/17

Weather
The following restrictions can occur under unj
favorable weather or light conditions:'yPoorer vehicle recognition.'yShort-term interruptions for vehicles that
are already recognized.
Examples of unfavorable weather or light conj
ditions:
'yWet conditions.'ySnowfall.'ySlush.'yFog.'yGlare.
Drive attentively, and react to the current traffic situation. If necessary, intervene actively, for
instance by braking, steering or evading.
Engine
power The desired speed is also maintained downhill,but may not be maintained on uphill grades if
engine power is insufficient.
Malfunction
The system cannot be activated if the radar
sensor is not aligned correctly. This may be
caused by damage incurred, for instance durj
ing parking.
A Check Control message is displayed if the system fails.
Cruise
controlThe
concept
Using this system, a desired speed can be adj justed using the buttons on the steering wheel.
The system maintains the desired speed. The system accelerates and brakes automaticallyas needed.
General
information
Depending on the driving settings, the features of the cruise control can change in certain
areas.
Safety
information WARNING
The system does not relieve from perj
sonal responsibility to assess the traffic situaj tion. Based on the limits of the system, it canj
not independently react to all traffic situations.
There is a risk of an accident. Adjust driving
style to traffic conditions. Watch traffic closely
and actively intervene where appropriate.'

ButtonFunctionResume speed, continue cruise conjtrol, refer to page 156.Rocker switch: adjust speed, refer to
page 155.
Switching
on/off
and
interrupting
cruise
control
Switching
on Press button on the steering wheel.
The marking in the speedometer is set to the
current speed.
Cruise control can be used.
DSC Dynamic Stability Control is switched on,
if necessary.
Switching
off Press button on the steering wheel.
'yIf active: press twice.'yIf interrupted: press once.
The displays go out. The stored desired speed
is deleted.
Interrupting
manually When active, press the button on the
steering wheel.
Interrupting
automatically The system is automatically interrupted in thefollowing situations:
'yWhen the driver applies the brakes.'yIf the clutch pedal is depressed for a few
seconds or released while a gear is not enj gaged.'yIf the gear engaged is too high for the curj
rent speed.'yWhen selector lever position D is disenj
gaged.'yDynamic Traction Control DTC is activated
or DSC Dynamic Stability Control is deactij vated.'yIf DSC Dynamic Stability Control interj
venes.'yWhen SPORT+ is activated with Driving
Dynamics Control.
Setting
the
speed
Maintaining/storing
the
speed
Press the rocker switch while the system is inj terrupted.
When the system is switched on, the current
speed is maintained and stored as the desired
speed.
The stored speed is displayed in the speedomj
eter and in the instrument cluster, refer to
page 156.
DSC Dynamic Stability Control is switched on,
if necessary.
The speed can also be stored by pressing a button.
Press button.
Seite 155Driving
comfortControls155
Online Edition for Part no. 01402981270 - VI/17

Changing
the
speed
Press the rocker switch up or down repeatedly
until the desired speed is set.
If active, the displayed speed is stored and the vehicle reaches the stored speed when the
road is clear.
'yEach time the rocker switch is pressed to
the point of resistance, the desired speed increases or decreases by approx.
1 mph/1 km/h.'yEach time the rocker switch is pressed
past the point of resistance, the desired
speed increases or decreases by a maxij
mum of 5 mph/10 km/h.
The maximum speed that can be set dej
pends on the vehicle.'yPressing the rocker switch to the resistj
ance point and holding it accelerates or dej
celerates the vehicle without requiring
pressure on the accelerator pedal.
After the rocker switch is released, the vej
hicle maintains its final speed. Pressing the
switch beyond the resistance point causes
the vehicle to accelerate more rapidly.
Continuing
cruise
control
General
information
An interrupted cruise control can be continued
by calling up the stored speed.
Make sure that the difference between current speed and stored speed is not too large before
calling up the stored speed. Otherwise, uninj
tentional braking or accelerating may occur.
In the following cases, the stored speed value
is deleted and cannot be called up again:'yWhen the system is switched off.'yWhen the ignition is switched off.
Calling
up
stored
speed
Press button on the steering wheel.
The stored speed is reached again and mainj tained.
Displays
in
the
instrument
cluster
Indicator
lamp Depending on how the vehicle is equipj
ped, the indicator lamp in the instruj
ment cluster indicates whether the sysj
tem is switched on.
Desired
speed
and
stored
speed
'yMarking lights up green:
system is active, the markj
ing indicates the desired
speed.'yMarking lights up orange:
system is interrupted, the
marking indicates the stored
speed.'yThe marking does not light up: the system is switched off.
Status
display
Selected desired speed.
If no speed is indicated, it is possible that the
conditions necessary for operation are not curj rently fulfilled.
Seite 156ControlsDriving
comfort156
Online Edition for Part no. 01402981270 - VI/17

System
limits
Engine
power The desired speed is also maintained downhill,
but may not be maintained on uphill grades if
engine power is insufficient.
PDC
Park
Distance
Control Concept
PDC is a support when parking. When you
slowly approach an object in the rear - or also
in the front of the vehicle if the feature is availaj
ble - then the object is reported through:'ySignal tones.'yVisual display.
With appropriate equipment: obstacles on the side of the vehicle that are detected by the
sensors of the parking assistant can also be rej
ported by the PDC. See side protection, refer to page 159.
General
information
The ultrasound sensors for measuring the disj
tances are located in the bumpers.
The maneuvering range, depending on the obj
stacle and environmental conditions, is approx.
6 ft/2 m.
An acoustic warning is first given in the followj
ing situations:
'yBy the front sensors and the two rear corj
ner sensors at approx. 24 in/60 cm from
the object.'yBy the rear middle sensors at a distance to
the object of approx. 5 ft/1.50 m.'yWhen a collision is imminent.'yWith parking assistant: by the side sensors at approx. 24 in/60 cm from the object.Safety
information
WARNING
The system does not relieve from perj
sonal responsibility to assess the traffic situaj tion. Based on the limits of the system, it canjnot independently react to all traffic situations.
There is a risk of an accident. Adjust driving style to traffic conditions. Watch traffic closelyand actively intervene where appropriate.'

'yDo not cover sensors, for instance withstickers, bicycle racks.'yKeep the sensors clean and unobstructed.
Switching
on/off
Switching
on
automatically The system switches on automatically in thefollowing situations:
'yIf selector lever position R is engagedwhen the engine is running.
The rearview camera also switches on.'yIf equipped with parking assistant: when
obstacles are detected behind or in front of the vehicle by PDC and the speed is slower
than approx. 2.5 mph/4 km/h.
You may switch automatic activation on and off
when obstacles are detected. Using iDrive:
1."My Vehicle"2."Vehicle settings"3."Parking"4."Automatic PDC activation": only with rej spective equipment.5."Automatic PDC activation"
The setting is stored for the driver profile
currently used.
If necessary, switch off automatic PDC activaj tion on obstacle detection, for instance in vehij
cle washes, to reduce false alarms.
Automatic
deactivation
during
forward
travel
The system switches off when a certain driving
distance or speed is exceeded.
Switch the system back on, if needed.
With
front
PDC:
switching
on/off
manually
Press park assistance button.
'yOn: the LED lights up.'yOff: the LED goes out.
The rearview camera image is displayed if the
reverse gear is engaged when pressing the
park assistance button.
WARNING
Signal
tones An intermittent tone indicates when the vehijcle is approaching an object. E.g., if an object
is detected to the left rear of the vehicle, a sigj
nal tone sounds from the left rear speaker.
The shorter the distance to the object, the
shorter the intervals.
If the distance to a detected object is less than
approx. 10 inches/25 cm, a continuous tone is sounded.
With front PDC: if objects are simultaneously located both in front of and behind the vehicle, an alternating continuous signal is sounded.
The signal tone is switched off, when selector
lever position P is engaged on vehicles with Steptronic transmission.
Volume
The ratio of the PDC signal tone volume to the entertainment volume can be adjusted.
Using iDrive:
1."My Vehicle"2."iDrive settings"3."Tone"4."Volume settings"5."PDC"6.Set the desired value.
The setting is stored for the driver profile curj
rently used.
Seite 158ControlsDriving
comfort158
Online Edition for Part no. 01402981270 - VI/17

Visual
warning
The approach of the vehicle to an object is
shown on the Control Display. Objects that are farther away are already displayed on the Conjtrol Display before a signal sounds.
A display appears as soon as Park Distance
Control (PDC) is activated.
The range of the sensors is represented in the
colors green, yellow and red.
When the image of the rearview camera is disj played, the switch can be made to PDC:
1.Move the Controller to the left, if needed.2. "Rear view camera"
With
appropriate
protection:
side
protection
Concept
The system warns of obstacles on the side of
the vehicle.
General
information
The system uses the ultrasound sensors of
PDC and parking assistant.
Display
To protect the sides of the vehicle, obstacle markings are displayed on the vehicle at the
sides.
'yColor markings: warning against detected
obstacles.'yGray markings, hatched area: no obstacles were detected.'yNo markings, black area: the area next to
the vehicle was not yet captured.
Limits
of
side
protection
The system only displays stationary obstaclesthat were previously detected by sensors whilepassing them.
The system does not detect whether an obstaj cle moves later on. If the vehicle is stationary,
the markings are shown in black after a certain time. The area next to the vehicle must be
newly captured.
System
limits
Safety
information WARNING
The system can react not at all, too late,
incorrectly, or without justification due to the
system limits. There is a risk of accidents or
risk of damage to property. Follow the informaj
tion regarding the system limits and actively
intervene, if needed.'

Limits
of
ultrasonic
measurement
Ultrasonic measurements might not function in
the following situations:'yFor small children and animals.'yFor persons with certain clothing, for inj
stance coats.'yWith external interference of the ultraj
sound, for instance from passing vehicles or loud machines.'yWhen sensors are dirty, iced over, damj
aged or out of position.'yUnder certain weather conditions such as
high relative humidity, wet conditions,
snowfall, extreme heat, or strong wind.'yWith tow bars and trailer couplings of other vehicles.'yWith thin or wedge-shaped objects.'yWith moving objects.'yWith elevated, protruding objects such asledges or cargo.'yWith objects with corners and sharp edges.'yWith objects with a fine surface structuresuch as fences.'yFor objects with porous surfaces.'yIf cargo protrudes.'yLow objects already displayed, for instance
curbs, can move into the blind area of the sensors before or after a continuous tone
sounds.
False
warnings
The system may issue a warning under the folj lowing conditions even though there is no objstacle within the detection range:
'yIn heavy rain.'yWhen sensors are very dirty or coveredwith ice.'yWhen sensors are covered in snow.'yOn rough road surfaces.'yOn uneven surfaces, such as speed
bumps.'yIn large buildings with right angles and
smooth walls, for instance in underground
garages.'yIn automatic vehicle washes.'yDue to heavy exhaust.'yDue to other ultrasound sources, for inj
stance sweeping machines, high pressure steam cleaners or neon lights.
As soon as the malfunction due to other ultraj
sound sources is no longer present, the sysj tem is again fully functional.
If necessary, switch off automatic PDC activaj tion on obstacle detection, for instance in vehij
cle washes, to reduce false alarms.
Malfunction
A Check Control message is displayed.
The range of the sensors is shown as a shaded area on the Control Display.
PDC has failed. Have the system checked by a
dealerss service center or another qualified service center or repair shop.
Rearview
camera
Concept
The rearview camera provides assistance in parking and maneuvering backwards. The area
behind the vehicle is shown on the Control
Display.
Safety
information WARNING
The system does not relieve from perj
sonal responsibility to assess the traffic situaj tion. There is a risk of an accident. Adjust drivj
ing style to traffic conditions. Watch traffic and
vehicle surroundings closely and actively interj
vene where appropriate.'