BMW 3 SERIES 2004 E46 Bluetooth Hadsfree Kit Upgrade Installation Instruction Manual
Page 11 of 14
EN/11
Retrofit kit No. 84 64 0 152 501
Installation Instructions No. 01 29 0 152 511 Issue date: 07.2002
6. To install and connect the eject box
0
0
0
00
Put the WDCT aerial
D
onto the holder
C
and screw it on
using hexagonal nuts
J
.
Connect the white FAKRA plug (1) to the WDCT aerial
D
.
0
Insert the WDCT aerial and holder
C
into the mounting in
the centre console (1).
Push on the speed nuts
I
.
0
0
Clip the eject box
A
into the telephone console insert
B
.
0
Clip the telephone console insert and eject box
A
into the
oddments box (1).
J
C
1D
046 0966 Z
IC
1
046 0967 Z
A
B
046 0774 Z0460774Z046 0968 Z
A
1
046 0969 Z
Page 12 of 14
EN/12
Retrofit kit No. 84 64 0 152 501
Installation Instructions No. 01 29 0 152 511 Issue date: 07.2002
6. To install and connect the eject box
0
0
Connect the black 18-pin plug (1) of the eject box to the
plug
X4545
on the standard wiring harness.
Connect the FAKRA plug of the eject box (2) to the black
FAKRA plug on the standard aerial cable (3).
X4545
23
1
046 0970 Z
Page 13 of 14
EN/13
Retrofit kit No. 84 64 0 152 501
Installation Instructions No. 01 29 0 152 511 Issue date: 07.2002
7. To install the hands-free microphone
0
00
Cars with SA 401 only
Release the tied back plug
X4221
from the standard
wiring harness and connect it to the hands-free
microphone
E
.
The arrow on the hands-free microphone
E
must
point to the front of the car.
Clip the hands-free microphone
E
into the trim (1).
0
Cars without SA 401 only
Release the tied back plug
X4221
from the standard
wiring harness and connect it to the hands-free
microphone
E
.
The arrow on the hands-free microphone
E
must
point to the front of the car.
Clip the hands-free microphone
E
into the trim (1).
E
1
X4221
046 0971 Z
E
1
X4221
046 0972 Z
Page 14 of 14
EN/14
Retrofit kit No. 84 64 0 152 501
Installation Instructions No. 01 29 0 152 511 Issue date: 07.2002
8. Concluding work
0
This upgrade system does not require coding.
- Connect battery
- Conduct a brief test with DISPlus/MoDiC III/GT1.
- Synchronize the mobile phone and the universal charger/hands-free electronic control unit
- Activate the Bluetooth function of the mobile phone (see the mobile phone owner's manual)
- Press and hold the push-to-talk button for about 1 second whilst switching on terminal R
- Release the push-to-talk button. The radio display shows
"BT CONNECTION"
and the MID or on-board
monitor displays
"BLUETOOTH CONNECTION"
.
The checklamps on the MID or on-board monitor flash during the connection phase.
- Activate the "Locate Bluetooth Devices" menu on the mobile phone (see the mobile phone owner's
manual). This process may take a few minutes.
- Work through additional menus in accordance with the instructions displayed on the mobile phone
- When prompted to do so, enter the 4 digit
"BLUETOOTH PASSKEY"
(see the sticker on the owner's
manual) using the mobile phone keypad
- The radio, MID or on-board monitor displays
"SUCCESSFUL"
to confirm that synchronisation has been
carried out correctly
- Switch off the ignition – the connection is terminated
- Conduct a function test
- Assemble the car again following the instructions to dismantle it in reverse order
Refer the DIS (Diagnostic Information System) for the circuit diagram of the telephone preparation
(SA 640), if required.