BMW 4 SERIES COUPE 2017 Owners Manual

Front
lights,
bulb
replacement
Xenon
headlights
Information DANGER
There can be high voltage in the lighting
system. There is danger to life. The manufacj
turer of your vehicle recommends that the work on the lighting system including bulb rejplacement be performed by a dealerss service
center or another qualified service center or rej pair shop.'

Halogen
front
fog
lightsObserve the safety information, refer to
page 230.
35-watt bulb, H8.1.Use the handle of the screwdriver from the onboard vehicle tool kit to remove the
three wheel house panel screws, arrow 1. Carefully pull back the wheel house panel,
arrow 2.2.Pull off the bulb connector, arrow 1.
Turn the bulb, arrow 2.
Left side of vehicle: turn clockwise.
Right side of vehicle: turn counterclockj wise.
Remove the bulb.3.Insert the new bulb, connect the connector and screw on the wheel house panel.
Turn
signal
in
exterior
mirror
The turn signals in the exterior mirrors feature
LED technology. In the case of a malfunction, contact a dealerss service center or another
qualified service center or repair shop.
Tail
lamps,
bulb
replacement
Overview1Turn signal2Reversing lamp3Inside brake lamp4Tail lamps5Outside brake lamp
Bulb
replacement,
exterior
tail
lamps General
information
Observe the safety information, refer to page 230.
Turn signal: 21-watt bulb, P21WLL.
Outer brake lamp: 21-watt bulb, H21WLL.
The tail lamps feature LED technology. In the
case of a malfunction, contact a dealerss servj ice center or another qualified service center or
repair shop.
Seite 232MobilityReplacing
components232
Online Edition for Part no. 01 40 2 974 422 - X/16

Removing
the
exterior
tail
lamp1.Open tailgate.2.Use the screwdriver to unscrew the threefixings, arrows, and take off the cover from
the top.3.Loosen the two nuts with the screwdriver handle, arrows.4.Grasp the inner edge of the tail lamp, arjrow 1, and carefully pull it backward andout, arrow 2. Use your free hand to hold it
in place in order to prevent the tail lamp from coming loose suddenly. Make surethat the foam rubber sealing ring is on the
centering pin.5.Release the catch at the top on the conj nector of the connecting line and remove
the connector from the bulb holder.
Replacing
the
bulbs
1.Loosen the three fasteners, arrows 1, on the bulb holder and remove the bulb holderfrom the tail lamp, arrow 2.2.Press the nonworking bulb gently into thesocket, turn counterclockwise and remove.3.Proceed in the reverse order to insert thenew bulb and attach the bulb holder. Make
sure that the bulb holder engages in all fasj
teners.
Installing
the
tail
lamp
1.Connect the connecting line to the tail
lamp and secure the bulb holder in the clip.2.Make sure that the foam rubber sealing
ring is on the centering pin, arrow 2, and is
not damaged.3.Position and firmly press the outer part of the tail lamp onto the rubber mount, arjSeite 233Replacing
componentsMobility233
Online Edition for Part no. 01 40 2 974 422 - X/16

row 1 and the inner part onto the centering
component, arrow 2. Make sure that the
tail lamp engages in the rubber mount.4.Screw the tail lamp on with the two nuts.5.Insert and secure the cover. Make sure that
the tubular seal is not pinched.
Lights
in
the
tailgate
General
information
Observe the safety information, refer to page 230.
Reversing lights: 16-watt bulb, PW16W.
Inner brake lights: 21-watt bulb, H21W All lights in the tailgate are made using LEDtechnology. In the case of a malfunction, conj
tact a dealerss service center or another qualij fied service center or repair shop.
Accessing
the
lights
Slide the cover outwards, arrow, and remove.
Replacing
the
reversing
lights
and
inner
brake
lights1.Loosen the bottom holder, arrow 1.2.Loosen the top holder, arrow 2. To do so, press in the middle latch and then press
out both outside latches.
Remove the lamp holder, arrow 3.3.Unscrew the nonworking bulb of the rej versing or brake lamp from its socketcounterclockwise.4.Insert the new bulb.
Installing
the
bulb
holder
1.Insert the two contacts, arrow 1, into the
connections, arrow 2.2.Press on the bulb holder, arrow 3. Make
sure that the two exterior holders latch into
place.3.Place the cover back in position and slide it
inwards.
Tail
lamps,
license
plate
lamps
and
center
brake
lamps
These lights are made using LED technology.
In the case of a malfunction, contact a dealerss
Seite 234MobilityReplacing
components234
Online Edition for Part no. 01 40 2 974 422 - X/16

service center or another qualified service cenj
ter or repair shop.
Vehicle
battery Maintenance
The battery is maintenance-free.
The added amount of acid is sufficient for the service life of the battery.
More information about the battery can be rej quested from a dealerss service center or anjother qualified service center or repair shop.
Replacing
the
vehicle
battery
General
information
After a battery replacement, the manufacturer
of your vehicle recommends that the vehicle
battery be registered on the vehicle by a dealj
erss service center or another qualified service center or repair shop to ensure that all comfortfeatures are fully available and that any Check
Control messages of these comfort features
are no longer displayed.
Safety
information NOTE
Vehicle batteries that are not compatible
can damage vehicle systems and impair vehij
cle functions. There is a risk of personal and
property damage. Only vehicle batteries that are compatible with your vehicle type should
be installed in your vehicle. Information on
compatible vehicle batteries is available at your
dealerss service center.'

Maintain the battery in an upright position fortransport and storage. Secure the battery so
that it does not tip over during transport.
Fuses Safety
information WARNING
Incorrect and repaired fuses can overload
electrical lines and components. There is a risk of fire. Never attempt to repair a blown fuse.Do not replace a nonworking fuse with a subj
stitute of another color or amperage rating.'

2.Reach under the cargo floor panel and fold
the cargo floor panel up, arrow.
Information on the fuse types and locations is
found on a separate sheet.
Attaching
the
cargo
floor
panel
1.Proceed in the reverse order to attach thecargo floor panel.2.Pull the cargo floor panel to the loading lip,
arrow 1, and press downward, arrow 2.Seite 237Replacing
componentsMobility237
Online Edition for Part no. 01 40 2 974 422 - X/16

Breakdown
assistanceVehicle
features
and
options
This chapter describes all standard, country- specific and optional features offered with theseries. It also describes features that are notnecessarily available in your vehicle, e. g., due
to the selected options or country versions.
This also applies to safety-related functions
and systems. When using these functions and systems, the applicable laws and regulations
must be observed.
Hazard
warning
flashers
The button is located in the center console.
The red light in the button flashes when the
hazard warning flashers are activated.
Intelligent
emergency
call
Concept
In case of an emergency, an Emergency Rej
quest can be made through the system.
General
information Only press the SOS button in an emergency.
For technical reasons, the Emergency Request cannot be guaranteed under unfavorable conj
ditions.
Overview
SOS button in the roofliner
Functional
requirements
'yThe SIM card integrated in the vehicle hasbeen activated.'yThe radio-ready state is switched on.'yThe Assist system is functional.
Initiating
an
Emergency
Request
automatically
Under certain conditions, such as if the airbags
trigger, an Emergency Request is automatij
cally initiated immediately after a severe accij
dent. Automatic Collision Notification is not afj
fected by pressing the SOS button.
Initiating
an
Emergency
Request
manually
1.Press the cover briefly to open it.2.Press the SOS button until the LED at the button lights up green.'yThe LED flashes green when a connectionto the BMW Response Center has been
established.
If the LED is flashing green, but the BMW Response Center cannot be heard on the
hands-free system, the hands-free system
may possibly be malfunctioning. However,
the BMW Response Center may still be
able to hear you.Seite 238MobilityBreakdown
assistance238
Online Edition for Part no. 01 40 2 974 422 - X/16

When the Emergency Request is received
at the BMW Response Center, the BMW
Response Center contacts you and takes
further steps to help you.
Even if you are unable to respond, the
BMW Response Center can take further steps to help you under certain circumj
stances.
For this, data is transmitted to the BMW
Response Center which serves to deterj
mine the necessary rescue measures. E.g., the current position of the vehicle, if it canbe established.
Roadside
Assistance
Service
availability Roadside Assistance can be reached aroundthe clock in many countries. You can obtain asj
sistance there in the event of a vehicle breakj
down.
Roadside
Assistance The Roadside Assistance phone number can
be viewed via iDrive or a connection to Roadj
side Assistance can be established directly.
Warning
triangle
The warning triangle is located in the tailgate. To open the catches, arrows, turn through 90p.
Fold back the trim.
First-aid
kit
General
information
Some of the articles have a limited service life.
Check the expiration dates of the contentsregularly and replace any expired items
promptly.
Storage
The first-aid kit is located behind the left-hand
cover in the cargo area.
Jump-starting General
information
If the battery is discharged, the engine can be
started using the battery of another vehicle and two jumper cables. Only use jumper caj
bles with fully insulated clamp handles.
Safety
information DANGER
Contact with live components can lead to
an electric shock. There is a risk of injuries or danger to life. Do not touch any componentsthat are under voltage.'

PreparationNOTE
In the case of body contact between the
two vehicles, a short circuit can occur during jump-starting. There is a risk of property damj
age. Make sure that no body contact occurs.'