BMW 4 SERIES COUPE 2017 Owners Manual

4.Make sure that the vehicle jack foot is exjtended vertically.5.Make sure that the vehicle jack foot stands
vertically and perpendicularly beneath the jacking point after extending the vehicle
jack.6.Crank up the vehicle jack until the entire
surface of the jack is in contact with the
ground and the wheel in question is raised
a maximum of 1.2 inches/3 cm off the ground.
Wheel
mounting
Mount a maximum of one emergency wheel.
1.Unscrew the lug bolts and remove the
wheel.2.Put the new wheel or emergency wheel on and hand-tighten at least two bolts in a
crosswise pattern.
If non-original light-alloy wheels of the vej hicle manufacturer are mounted, the acj
companying lug bolts may have to be used
as well.3.Hand-tighten the remaining lug bolts and tighten all bolts well in a crosswise pattern.4.Turn the crank of the vehicle jack counterj
clockwise to retract the vehicle jack and
lower the vehicle.5.Remove the vehicle jack.
After
the
wheel
change
1.Tighten the lug bolts crosswise. The tightj ening torque is 101 lb ft/140 Nm.2.Stow the nonworking wheel in the cargo
area.
The nonworking wheel cannot be stored under the cargo floor panel because of its
size.3.Check tire inflation pressure at the next opj
portunity and correct as needed.4.Reinitialize the Flat Tire Monitor.
Reset the Tire Pressure Monitor.5.Check to make sure the lug bolts are tight
with a calibrated torque wrench.6.Drive to the nearest dealerss service center
or another qualified service center or repair
shop to have the damaged tire replaced.Seite 211Wheels
and
tiresMobility211
Online Edition for Part no. 01 40 2 973 409 - VI/16

Engine
compartmentVehicle
features
and
optionsThis chapter describes all standard, country-specific and optional features offered with theseries. It also describes features that are notnecessarily available in your vehicle, e. g., dueto the selected options or country versions.
This also applies to safety-related functions
and systems. When using these functions and systems, the applicable country provisions
must be observed.
Important
features
in
the
engine
compartment
1Jump-starting, negative battery terminal2Vehicle identification number3Washer fluid reservoir4Jump-starting, positive battery terminal5Engine compartment fuse box6Oil filler neck7Coolant reservoir
Depending on the engine installation, the
coolant reservoir is located on the right
side or the left side of the engine compartj
ment.Seite 212MobilityEngine
compartment212
Online Edition for Part no. 01 40 2 973 409 - VI/16

Hood
Safety
information WARNING
Improperly executed work in the engine
compartment can damage vehicle compoj nents and impair vehicle functions. There is a
risk of personal and property damage. The
manufacturer of your vehicle recommends that, in the effort to avoid such risks, work inthe engine compartment be performed by a
dealerss service center or another qualified
service center or repair shop.'

Engine
oilVehicle
features
and
options
This chapter describes all standard, country- specific and optional features offered with theseries. It also describes features that are notnecessarily available in your vehicle, e. g., due
to the selected options or country versions.
This also applies to safety-related functions
and systems. When using these functions and systems, the applicable country provisions
must be observed.
General
information
The engine oil consumption is dependent on
the driving style and driving conditions.
The engine oil consumption can increase in
the following situations, for example:'ySporty driving style.'yBreak-in of the engine.'yIdling of the engine.'yWith use of engine oil types that are classij
fied as not suitable.
Therefore, regularly check the engine oil level
after refueling.
The vehicle is equipped with electronic oil
measurement.
The electronic oil measurement has two measj uring principles:
'yStatus display.'yDetailed measurement.Electronic
oil
measurement
Status
display
Concept
The engine oil level is monitored electronically
while driving and shown on the Control Disj play.
If the engine oil level reaches the minimum
level, a Check Control message is displayed.
Requirements A current measured value is available after apj
prox. 30 minutes of driving. During a shorter
trip, the status of the last, sufficiently long trip
is displayed.
With frequent short-distance trips, regularly perform a detailed measurement.
Displaying
the
engine
oil
level Via iDrive:1."Vehicle info"2."Vehicle status"3. "Engine oil level"
The engine oil level is displayed.
Engine
oil
level
display
messages
Different messages appear on the display dej pending on the engine oil level. Pay attention
to these messages.
If the engine oil level is too low within the next
125 miles/200 km, add engine oil.
A red indicator lamp indicates too high
engine oil pressure.
NOTE
An engine oil level that is too low causes
engine damage. There is a risk of property
damage. Immediately add engine oil.'

Take care not to add too much engine oil.NOTE
Too much engine oil can damage the enj
gine or the catalytic converter. There is a risk
of property damage. Do not add too much enj
gine oil. When too much engine oil is added,
have oil level corrected by a dealerss service
center or another qualified service center or rej pair shop.'

center or another qualified service center or rejpair shop.'

Engine
oil
changeNOTE
Engine oil that is not changed in timely
fashion can cause increased engine wear and
thus engine damage. There is a risk of property damage. Do not exceed the service data indijcated in the vehicle.'

CoolantVehicle
features
and
optionsThis chapter describes all standard, country-specific and optional features offered with theseries. It also describes features that are notnecessarily available in your vehicle, e. g., due
to the selected options or country versions.
This also applies to safety-related functions
and systems. When using these functions and systems, the applicable country provisions
must be observed.
General
information
Not all commercially available additives are
suitable for the vehicle. Information about suitj
able additives is available from a dealerss servj
ice center or another qualified service center or
repair shop.
Safety
information WARNING
With the engine hot and the cooling sysj
tem open, coolant can escape and lead to scalding. There is a risk of injury. Only openthe cooling system with the engine cooleddown.'

Checking
the
coolant
level
in
the
filler
neck
There are yellow Min and Max marks in the
coolant reservoir.1.Let the engine cool.2.Turn the lid of the coolant reservoir slightly counterclockwise to allow any excess
pressure to dissipate, then open it.3.Open the coolant reservoir lid.4.The coolant level is correct if it lies bej tween the minimum and maximum marksin the filler neck.Adding1.Let the engine cool.2.Turn the lid of the coolant reservoir slightlycounterclockwise to allow any excess
pressure to dissipate, then open it.3.If the coolant is low, slowly add coolant up to the specified level; do not overfill.4.Turn the lid until there is an audible click.The arrows on the coolant reservoir andthe lid must point towards one another.5.Have the cause of the coolant loss elimijnated as soon as possible.
Disposal
Comply with the relevant environmenj
tal protection regulations when disposj
ing of coolant and coolant additives.
Seite 219CoolantMobility219
Online Edition for Part no. 01 40 2 973 409 - VI/16

MaintenanceVehicle
features
and
options
This chapter describes all standard, country- specific and optional features offered with theseries. It also describes features that are notnecessarily available in your vehicle, e. g., due
to the selected options or country versions.
This also applies to safety-related functions
and systems. When using these functions and systems, the applicable country provisions
must be observed.
BMW
maintenance
system The maintenance system indicates requiredmaintenance measures, and thereby provides
support in maintaining road safety and the opj erational reliability of the vehicle.
In some cases, scopes and intervals may vary
according to the country-specific version. Rej
placement work, spare parts, fuels and lubrij
cants, and wear materials are calculated sepaj rately. Further information is available from a
dealerss service center or another qualified service center or repair shop.
Condition
Based
Service
CBS
Sensors and special algorithms take into acj
count the driving conditions of the vehicle.
Based on this, Condition Based Service recogj
nizes the maintenance requirements.
The system makes it possible to adapt the
amount of maintenance corresponding to your
user profile.
Information on service requirements can be
displayed on the Control Display.Service
data
in
the
remote
control
Information on the required maintenance iscontinuously stored in the remote control. Thedealerss service center can read this data outand suggest a maintenance scope for the vehijcle.
Therefore, hand the service advisor the remote
control with which the vehicle was driven most
recently.
Storage
periods Storage periods during which the vehicle batj
tery was disconnected are not taken into acj count.
If this occurs, have a dealer's service center or another qualified service center or repair shop update the time-dependent maintenance projcedures, such as checking brake fluid and, if
necessary, changing the engine oil and the mij crofilter/activated-charcoal filter.
Service
and
WarrantyInformation
Booklet
for
US
models
and
Warranty
and Service
Guide
Booklet
for
Canadian
models
Please consult your Service and Warranty Inj
formation Booklet for US models and Warranty and Service Guide Booklet for Canadian modjels for additional information on service rejquirements.
The manufacturer of your vehicle recommends that maintenance and repair be performed by a
dealerss service center or another qualified service center or repair shop. Records of reguj
lar maintenance and repair work should be rej
tained.Seite 220MobilityMaintenance220
Online Edition for Part no. 01 40 2 973 409 - VI/16