BMW 4 SERIES COUPE 2019 Owners Manual

9Recirculated-air mode10Interior temperature sensorClimate
control
functions
in
detail
Switching
the
system
on/off
Switching
on
Press any button except for the following:'xRear window defroster.'xSeat heating.
Switching
off
Press the left button for the minimumspeed.
Temperature
Concept
The automatic climate control achieves the set
temperature as quickly as possible, if necessary by using the maximum cooling or heating power,and then keeps it constant.
Settings Turn the ring to set the desired
temperature.
Do not rapidly switch between different temperaj
ture settings. Otherwise, the automatic climate control will not have sufficient time to adjust the
set temperature.
Air
conditioning Concept
The air in the car's interior will be cooled and dej humidified and, depending on the temperaturesetting, warmed again.
The car's interior can only be cooled with the enj
gine running.
Switching
on/off Press button.
The LED is illuminated with air condij
tioning switched on.
Depending on the weather, the windshield and
side windows may fog up briefly when the enj gine is started.
The air conditioning is switched on automatically
with the AUTO program.
When using the automatic climate control, conj densation water, refer to page 229, develops
and drains underneath the vehicle. This is norj mal.
AUTO
program
Concept
Air flow, air distribution and temperature are conj
trolled automatically.
Switching
on/off Press button.
The LED is illuminated with the AUTO
program switched on.
Depending on the selected temperature and outj side influences, the air is directed to the windj
shield, side windows, upper body, and into the floor area.
The air conditioning, refer to page 201, is
switched on automatically with the AUTO proj gram.Seite 201Climate
controlCONTROLS201
Online Edition for Part no. 01402989120 - II/18

Recirculated-air
mode
Concept
You may react to unpleasant odors or pollutants
in the immediate environment by temporarily
suspending the supply of outside air. The system
then recirculates the air flow within the vehicle.
Operation Press button repeatedly to select an opjerating mode:'xLED off: outside air flows in continuously.'xLED on, recirculated-air mode: the supply of
outside air into the vehicle is permanently
blocked.
To prevent window fogging, recirculated-air
mode switches off automatically after a certain amount of time, depending on the environmental
conditions.
With constant recirculated-air mode, the air qualj ity in the car's interior deteriorates and the fogj
ging of the windows increases.
If the windows fog over, switch off recirculated-
air mode and increase the air flow, if needed.
Controlling
the
air
flow
manually
Concept
The air flow for climate control can be adjusted
manually.
Operation Press the left or right side of the button:
decrease or increase air flow.
The air flow from the air conditioner may be rej duced automatically to save battery power.
Controlling
the
air
distribution
manually
Concept
The air distribution for climate control can be adj
justed manually.
Operation Turn the wheel to select the dejsired program or the desired inj
termediate setting.'x Windows.'x Upper body region.'x Windows, upper body region, and floor
area.'x Floor area.
Defrosting
windows
and
removing
condensation
Make the following settings to defrost the winj
dows and remove condensation:
'xDirect the air distribution onto the windows.'xIncreasing the air flow.'xIncrease the temperature.'xSwitch on the air conditioning if needed.
Rear
window
defroster
Press button. The LED lights up.
The rear window defroster switches off
automatically after a certain period of time.
Microfilter
In external and recirculated-air mode the microfilj
ter filters dust and pollen from the air.
Have this filter changed during vehicle maintej
nance, refer to page 274.
Seite 202CONTROLSClimate
control202
Online Edition for Part no. 01402989120 - II/18

Automatic
climate
control
with
enhanced
features1Seat heating, left\_912Temperature, left3AUTO program4Display5Maximum cooling6Temperature, right7Seat heating, right\_ 918Air conditioning9Automatic recirculated-air control/recircuj
lated-air mode10Air distribution, right11Air flow, AUTO intensity12Air distribution, left13Rear window defroster14Interior temperature sensor n always keep clear15Defrosting windows and removing condensaj
tionClimate
control
functions
in
detail
Switching
the
system
on/off
Switching
on
Press any button except for the following:'xRear window defroster.'xSeat heating.Switching
off
Press the left button for the minimumspeed.
Temperature
Concept
The automatic climate control achieves the set
temperature as quickly as possible, if necessarySeite 203Climate
controlCONTROLS203
Online Edition for Part no. 01402989120 - II/18

by using the maximum cooling or heating power,
and then keeps it constant.
Settings Turn the ring to set the desired
temperature.
The automatic climate control reaches this temj perature as quickly as possible, if needed, by inj
creasing the cooling or heating output, and then
keeps it constant.
Do not rapidly switch between different temperaj ture settings. Otherwise, the automatic climate
control will not have sufficient time to adjust the
set temperature.
Air
conditioning
Concept
The air in the car's interior will be cooled and dej
humidified and, depending on the temperature setting, warmed again.
The car's interior can only be cooled with the enj gine running.
Switching
on/off Press button.
The LED is illuminated with air condij
tioning switched on.
Depending on the weather, the windshield and
side windows may fog up briefly when the enj gine is started.
The air conditioning is switched on automatically
with the AUTO program.
When using the automatic climate control, conj densation water, refer to page 229, develops
and drains underneath the vehicle. This is norj mal.Maximum
cooling
Concept
The system is set to the lowest temperature, opj
timum air flow and recirculated-air mode.
General
information
The function is available above an external temj perature of approx. 32 

In the AUTO program, the air flow may be rejduced during a phone call on the hands-free sysj
tem.
Intensity
With the AUTO program switched on, the intenj sity can be set. This changes the automatic conj trol for the air flow and air distribution.
Press the left or right side of the button:
decrease or increase intensity.
The selected intensity is shown on the display of
the automatic climate control.
Automatic
recirculated-air
control/
recirculated-air
mode
Concept
The automatic recirculated-air control AUC recj
ognizes odors or pollutants in the outside air. The outside air supply is shut off and the interiorair is recirculated.
General
information
If the system is activated, a sensor detects polluj tants in the outside air and controls the shut-offautomatically.
If the system is deactivated, outside air continuj
ously flows into the car's interior.
With constant recirculated-air mode, the air qualj
ity in the car's interior deteriorates and the fogj
ging of the windows increases.
Switching
on/off Press button repeatedly to select an opjerating mode:'xLEDs off: outside air flows in continuously.'xLeft LED on, automatic recirculated-air conj
trol: a sensor detects pollutants in the outside
air and shuts off automatically.'xRight LED on, recirculated-air mode: the supj
ply of outside air into the vehicle is permaj
nently blocked.Recirculated-air mode switches off automatically
at low external temperatures after a certain
amount of time in order to avoid window fogging.
If the windows are fogged over, switch off the rej
circulated-air mode and press the AUTO button
to utilize the condensation sensor. Make sure that air can flow to the windshield.
Controlling
the
air
flow
manually
Concept
The air flow for climate control can be adjusted
manually.
General
information
To manually adjust air flow switch off AUTO proj gram first.
Operation Press the left or right side of the button:
decrease or increase air flow.
The selected air flow is shown on the display of
the automatic climate control.
The air flow of the automatic climate control may
be reduced automatically to save battery power.
Controlling
the
air
distribution
manually
Concept
The air distribution for climate control can be adj
justed manually.
Operation Press button repeatedly to select a proj
gram:'xUpper body region.'xUpper body region and floor area.'xFloor area.'xWindows and floor area: driver's side only.Seite 205Climate
controlCONTROLS205
Online Edition for Part no. 01402989120 - II/18

'xWindows, upper body region and floor area:driver's side only.
If the windows are fogged over, press the AUTO
button to utilize the condensation sensor.
Defrosting
windows
and
removing
condensation
Concept
Ice and condensation are quickly removed from
the windshield and the front side windows.
Switching
on/off Press button.
The LED is illuminated with the system
switched on.
For this purpose, point the side vents towards the side windows as needed.
The air flow can be adjusted with the air flow acj
tive.
If the windows are fogged over, you can also
switch on the air conditioning or press the AUTO
button to utilize the condensation sensor.
Rear
window
defroster Press button. The LED lights up.
The rear window defroster switches off
automatically after a certain period of time.
Microfilter/activated-charcoal
filter In external and recirculated-air mode the microfilj
ter/activated charcoal filter filters dust, pollen, and
gaseous pollutants out of the air.
Have this filter changed during vehicle maintej
nance, refer to page 274.
Ventilation
Front
ventilation
'xLever for changing the air flow direction, arj
row 1.'xThumbwheels for opening and closing the
vents continuously, arrows 2.'xThumbwheel to vary the ventilation temperaj
ture in the upper body region, arrow 3.
Toward blue: colder.
Toward red: warmer.
This does not change the set interior temperj
ature for the driver and front passenger.
Settings
'xVentilation for cooling:
Direct vent in your direction when car's intej
rior is too hot.'xDraft-free ventilation:
Adjust the vent to let the air flow past you.Seite 206CONTROLSClimate
control206
Online Edition for Part no. 01402989120 - II/18

Ventilation
in
the
rear'xThumbwheel for variable opening and closingof the vents, arrow 1.'xThumbwheel to vary the ventilation temperaj
ture, arrow 2.
Toward blue: colder. Toward red: warmer.
This does not change the adjusted interior temperature.'xLever for changing the air flow direction, arj
row 3.
Parked-car
ventilation
Concept
The parked-car ventilation ventilates the car's inj terior and lowers its temperature, if needed.
General
information The parked-car ventilation can be switched onand off directly or by using two preset activation
times. The system remains switched on for
30 minutes.
The parked-car ventilation system is operated via
iDrive.
Functional
requirements
'xDirect operation: vehicle is in radio-ready
state.'xDirect operation or preset activation time:
does not depend on external temperature.'xBattery is sufficiently charged.
If parked-car ventilation is switched on, the vehicle battery will be discharged. Thus, limit
the maximum activation time to save the vej
hicle battery. The system will be available
again after the engine is started or after a
short trip.'xMake sure that the vehicle's date and time
are set correctly.'xOpen the vents to allow air to flow out.
Switching
on/off
directly
Via iDrive:
1."My Vehicle"2."Vehicle settings"3.If necessary, "Climate functions"4."Activate comfort ventilation now"
The symbol on the automatic climate control
flashes if the system is switched on.
Preselecting
the
activation
time
Via iDrive:
1."My Vehicle"2."Vehicle settings"3.If necessary, "Climate functions"4."Comfort ventilation"5.Select the desired activation time.6.Set the desired time.
Activating
the
activation
time Via iDrive:
1."My Vehicle"2."Vehicle settings"3.If necessary, "Climate functions"4."For start time at:"
Activate the desired activation time.
The symbol on the automatic climate control
lights up when the activation time is activated.
Seite 207Climate
controlCONTROLS207
Online Edition for Part no. 01402989120 - II/18

The symbol on the automatic climate control
flashes when the system has been switched on.
The system will only be switched on within the next 24 hours. After that, it needs to be reactij
vated.Seite 208CONTROLSClimate
control208
Online Edition for Part no. 01402989120 - II/18

Interior
equipmentVehicle
features
andoptions
This chapter describes all standard, country-spejcific and optional features offered with the series. It also describes features that are not necessarilyavailable in your vehicle, e. g., due to the selectedoptions or country versions. This also applies to
safety-related functions and systems. When usj
ing these functions and systems, the applicable laws and regulations must be observed.
Integrated
Universal Remote
Control
Concept
The integrated Universal Remote Control in the interior mirror can operate up to 3 functions of remote-controlled systems, such as garage doordrives, barriers, or lighting systems. The
Integrated Universal Remote Control replaces up to 3 different hand-held transmitters. To operate
the remote control, the buttons on the interior mirror must be programmed with the desiredfunctions. The hand-held transmitter for the parj
ticular system is required in order to program the
remote control.
Before selling the vehicle, delete the stored funcj tions for the sake of security.
Safety
information
WARNING
Body parts can be jammed when operating rej
mote-controlled systems, such as the garage door, using the integrated Universal Remote
Control. There is a risk of injury or risk of damj
age to property. Make sure that the area of
movement of the respective system is clear during programming and operation. Also follow
the safety information of the hand-held transj
mitter.
Compatibility If this symbol is printed on the packaging
or in the owner's manual of the system to
be controlled, the system is generally
compatible with the integrated Universal Remote
Control.
If you have any questions, please contact:'xA dealerss service center or another qualified
service center or repair shop.'xwww.homelink.com on the Internet.
HomeLink is a registered trademark of Gentex Corporation.
Control
elements
on
the
interior
mirror
'xLED, arrow 1.'xButtons, arrow 2.'xThe hand-held transmitter, arrow 3, is rej quired for programming.Seite 209*nterior
equipmentCONTROLS209
Online Edition for Part no. 01402989120 - II/18

Programming
General
information1.Switch on the ignition.2.Initial setup:
Press and hold the two outer buttons on the
interior mirror simultaneously for approxij
mately 20 seconds until the LED on the intej rior mirror flashes. This erases all programj
ming of the buttons on the interior mirror.3.Hold the hand-held transmitter for the system to be controlled approx. 1 to 3 inches/2.5 to
8 cm away from the buttons of the interior mirror. The required distance depends on the
hand-held transmitter.4.Simultaneously press and hold the button of
the desired function on the hand-held transj
mitter and the button to be programmed on the interior mirror. The LED on the interiormirror will begin flashing slowly.5.Release both buttons as soon as the LED
flashes more rapidly. The LED flashing faster indicates that the button on the interior mirrorhas been programmed.
If the LED does not flash faster after at least
60 seconds, change the distance between
the interior mirror and the hand-held transj mitter and repeat the step. Several more atj
tempts at different distances may be necesj
sary. Wait at least 15 seconds between
attempts.
Canada: if programming with the hand-held transmitter was interrupted, hold down the inj
terior mirror button and repeatedly press and
release the hand-held transmitter button for
2 seconds.6.To program other functions on other buttons,
repeat steps 3 to 5.
The systems can be controlled using the interior
mirror buttons.
Special
feature
of
the
rolling
code
wireless
system
If you are unable to operate the system after rej
peated programming, please check if the system to be controlled features a rolling code radio sysjtem.
Read the system's owner's manual, or press the
programmed button on the interior mirror longer. If the LED on the interior mirror starts flashing
rapidly and then stays lit constantly for 2 secj onds, the system features a rolling code radiosystem. Flashing and continuous illumination ofthe LED will repeat for approximately 20 secj
onds.
For systems with a rolling code radio system, the
integrated Universal Remote Control and the
system also have to be synchronized.
Please read the owner's manual to find out how to synchronize the system.
Synchronizing is easier with the aid of a second
person.
Synchronizing the universal remote control with the system:1.Park the vehicle within range of the remote-
controlled system.2.Program the desired button on the interior mirror as described.3.Locate and press the synchronizing button
on the system being programmed. You have approx. 30 seconds for the next step.4.Hold down the programmed button on the injterior mirror for approximately 3 seconds andthen release it. If necessary, repeat this step
up to three times in order to finish synchronij
zation. Once synchronization is complete, the
programmed function will be carried out.
Reprogramming
individual
buttons
1.Switch on the ignition.2.Press and hold the interior mirror button to be programmed.Seite 210CONTROLS*nterior
equipment210
Online Edition for Part no. 01402989120 - II/18