BMW 4 SERIES COUPE 2019 Manual PDF

3Open tailgate4Panic mode
UnlockingPress button on the remote control.
Depending on the settings, refer to page 81,
the following access points are unlocked:
'xDriver's door and fuel filler flap.
Press the button of the remote control again to unlock the other vehicle access points.'xAll doors, tailgate, and fuel filler flap.
In addition, the following functions are executed:
'xUnlocking is confirmed by the turn signalsand the horn. This function must be activated
in the settings, refer to page 81.'xThe settings stored in the driver profile, refer
to page 79, are applied.'xThe driver's seat is set to the last position
saved in the driver's profile. This function must be activated in the settings, refer topage 81.'xThe interior lights, refer to page 143, are
switched on, unless they were manually
switched off.'xDepending on the settings, the welcome light
and headlight courtesy delay feature, refer to
page 140, are switched on.'xThe alarm system, refer to page 83, is
switched off.
The light functions may depend on the ambient
brightness.
Convenient
opening Press and hold this button on the rej
mote control after unlocking.
Pressing and holding the button on the remote
control opens the windows and the glass sunj roof.
Locking1.Close the driver's door.2. Press button on the remote control.
The following functions are executed:
'xAll doors, the tailgate, and the fuel filler flapare being locked.'xLocking is confirmed by the turn signals and
the horn. This function must be activated in the settings, refer to page 81.'xThe alarm system, refer to page 83, is
switched on.
If the engine or ignition is still switched on when
you lock the vehicle, the vehicle horn honks twice. In this case, the engine or ignition must beswitched off by means of the Start/Stop button.
Switching
on
interior
lights
and
courtesy
light
Press button on the remote control with
the vehicle locked.
This function is not available, if the interior lights
were switched off manually.
The light functions may depend on the ambient
brightness.
After locking, wait 10 seconds before pressing the button again.
Tailgate General
information To avoid locking it in the vehicle, do not place theremote control in the cargo area.
Depending on the vehicle equipment and counj
try version, it is possible to specify whether the doors are also unlocked when unlocking with theremote control. Adjusting the settings, refer to
page 81.
The tailgate can only be opened if it is not
locked. Separately lock the tailgate, refer to page 79.
Seite 710pening
and
closingCONTROLS71
Online Edition for Part no. 01402989120 - II/18

Safety
information
WARNING
Body parts can be jammed when operating the tailgate. There is a risk of injury. Make sure thatthe area of movement of the tailgate is clear
during opening and closing.
NOTE
During opening, the tailgate pivots back and up.
There is a risk of damage to property. Make
sure that the area of movement of the tailgate
is clear during opening and closing.
Opening
Press button on the remote control forapprox. 1 second.
Panic
mode You can trigger the alarm system if you find yourjself in a dangerous situation.
'xPress button on the remote control
and hold for at least 3 seconds.'xBriefly press the button on the remote control three times in succession.
To switch off the alarm: press any button.
Replacing
the
battery
1.Remove the integrated key from the remote
control, refer to page 74.2.Place the integrated key underneath the batj
tery compartment cover, arrow 1, and lift thecover with a lever movement of the
integrated key, arrow 2.3.Push battery in the direction of the arrow usj
ing a pointed object and lift it out.4.Insert a type CR 2450 battery with the posij tive side facing up.5.Press the cover closed.6.Push the integrated key into the remote conj
trol until it engages.
Have old batteries disposed of by a dealj
erss service center or another qualified service center or repair shop or take
them to a collection point.
Additional
remote
controls
Additional remote controls are available from a
dealerss service center or another qualified servj ice center or repair shop.
Loss
of
the
remote
controls
A lost remote control can be blocked and rej placed by a dealerss service center or anotherqualified service center or repair shop.
Seite 72CONTROLS0pening
and
closing72
Online Edition for Part no. 01402989120 - II/18

Malfunction
General
information A Check Control message is displayed.
Remote control detection by the vehicle may malfunction under the following circumstances:'xThe battery of the remote control is disj
charged. Replacing the battery, refer to page 72.'xInterference of the radio connection from
transmission towers or other equipment with
high transmitting power.'xShielding of the remote control due to metal objects.
Do not transport the remote control together
with metal objects.'xInterference of the radio connection from moj
bile phones or other electronic devices in dij
rect proximity to the remote control.
Do not transport the remote control together
with electronic devices.'xInterference of radio transmission by a chargj
ing process of mobile devices, for instance charging of a mobile phone.'xThe remote control is in direct proximity of
the wireless charging tray.
Place the remote control down at a different location.
In the case of interference, the vehicle can beunlocked and locked from the outside with the
integrated key, refer to page 73.
Starting
the
engine
via
emergency
detection
of
the
remote
control
It is not possible to start the engine if the remote
control has not been detected.
Proceed as follows in this case:
1.Hold the remote control with its back against
the marked area on the steering column. Pay attention to the display in the instrumentcluster.2.If the remote control is detected:
Start the engine within 10 seconds.
If the remote control is not detected, slightly
change the position of the remote control and rej
peat the procedure.
Integrated
key
General
information The driver's door can be locked and unlockedwithout remote control using the integrated key.
The integrated key can also be used for theglove compartment on the front passenger side.
Safety
information
WARNING
Unlocking from the inside is only possible with special knowledge.
Seite 730pening
and
closingCONTROLS73
Online Edition for Part no. 01402989120 - II/18

Persons who spend a lengthy time in the vehij
cle while being exposed to extreme temperaj tures are at risk of injury or death. Do not lock
the vehicle from the outside when there are
people in it.
NOTE
The door lock is permanently joined with the
door. The door handle can be moved. When pulling the door handle with the integrated keyinserted, paint or the integrated key can be
damaged. There is a risk of damage to propj
erty. Remove the integrated key before pulling
the outside door handle.
Removing
Press the button, arrow 1, and pull out the
integrated key, arrow 2.
Locking/unlocking
via
the
door
lock
Unlock or lock the driver's door via the door lock
using the integrated key.
The other doors must be unlocked or locked from the inside.
Alarm
systemThe alarm system is not switched on if the vehijcle is locked with the integrated key.
The alarm system is triggered when the door is
opened, if the vehicle has been unlocked via the
door lock.
In order to stop the alarm, unlock the vehicle with
the remote control or switch on the ignition, if
needed, through emergency detection of the rej
mote control, refer to page 73.
Button
for
central
locking system
General
information In the event of a severe accident, the vehicle is
automatically unlocked. The hazard warning sysj
tem and interior lights come on.
Overview
Button for the central locking system.
Unlocking
and
locking
Press button. For locking, the doors must be
closed.
'xThe fuel filler flap remains unlocked.'xThe vehicle is not secured against theft when locking.Seite 74CONTROLS0pening
and
closing74
Online Edition for Part no. 01402989120 - II/18

Opening'x Press button to unlock the doors toj
gether, and then pull the door handle above
the armrest.'xOn the door to be opened, pull the door hanj
dle twice: the first time unlocks the door, the second time opens it. The other doors remain
locked.
Comfort
Access
Concept
The vehicle can be accessed without activating
the remote control.
All you need to do is to have the remote control
with you, such as in your pants pocket.
The vehicle automatically detects the remote
control when it is in close proximity or in the car's
interior.
General
information Comfort Access supports the following funcj
tions:
'xUnlocking and locking the vehicle.'xConvenient closing.'xOpening tailgate.'xOpen tailgate with no-touch activation.
Functional
requirements
'xTo lock the vehicle, the remote control must
be located outside of the vehicle near the
doors.'xThe next unlocking and locking cycle is not
possible until after approx. 2 seconds.Unlocking
Grasp the door handle on the driver's or front passenger door completely.
This corresponds with pressing the button

on the remote control.
Locking
Touch the surface on the door handle of the drivj
er's or front passenger door with your finger for
approx. 1 second without grasping the door hanj dle.
This corresponds with pressing the button

on the remote control.
Convenient
closing
Safety
information
WARNING
With convenient closing, body parts can be jammed. There is a risk of injury. Make surethat the area of movement of the doors is clearduring convenient closing.
Seite 750pening
and
closingCONTROLS75
Online Edition for Part no. 01402989120 - II/18

Closing
Touch the surface on the door handle of the drivj
er's or front passenger door, arrow, with your finj
ger and hold it there without grasping the door
handle.
This corresponds with pressing and holding the button
on the remote control.
In addition to locking, the windows and the glass sunroof close. The exterior mirrors fold in, dej
pending on the model.
Open
tailgate
General
information If you open the tailgate via Comfort Access,
locked doors will not be unlocked.
To avoid locking it in the vehicle, do not place the remote control in the cargo area.
Safety
information
WARNING
Body parts can be jammed when operating the tailgate. There is a risk of injury. Make sure that
the area of movement of the tailgate is clear
during opening and closing.
NOTE
During opening, the tailgate pivots back and up.
There is a risk of damage to property. Make
sure that the area of movement of the tailgate is clear during opening and closing.
Opening
Press button on the tailgate.
This corresponds with pressing the button
on the remote control.
Opening
tailgate
with
no-touch
activation
Concept
The tailgate can be opened with no-touch activaj
tion using the remote control you are carrying.
Two sensors detect a forward-directed foot moj
tion in the center of the area at the rear of the vej hicle and the tailgate is opened.
General
information To avoid locking it in the vehicle, do not place theremote control in the cargo area.
If the remote control is in the sensor area, the
tailgate may open or close inadvertently if you unintentionally move your foot or if somethingelse moves in the detection area.
The sensor has an approximate range of
5 ft/1.50 m extending from the rear of the vehij
cle.
Seite 76CONTROLS0pening
and
closing76
Online Edition for Part no. 01402989120 - II/18

If you open the tailgate with no-touch activation,
locked doors will not be unlocked.
Safety
information
WARNING
During no-touch activation, vehicle parts may be touched, such as the hot exhaust gas sysj tem. There is a risk of injury. When moving yourfoot, make sure you have a firm stance and do
not touch the vehicle.
WARNING
Body parts can be jammed when operating the
tailgate. There is a risk of injury. Make sure that the area of movement of the tailgate is clearduring opening and closing.
NOTE
During opening, the tailgate pivots back and up.
There is a risk of damage to property. Make
sure that the area of movement of the tailgate
is clear during opening and closing.
Performing
the
foot
movement
1.Stand in the middle behind the vehicle at apj prox. one arm's length away from the rear of
the vehicle.2.Wave a foot under the vehicle in the direction
of travel and immediately pull it back. Withthis movement, the leg must pass through
the ranges of both sensors.
Opening
Perform the foot movement described earlier.
Before the opening, the hazard warning system flashes.
Moving your foot again will stop the opening moj tion, and moving it one more time after that will close the trunk lid.
Malfunction Remote control detection by the vehicle maymalfunction under the following circumstances:
'xThe battery of the remote control is disj
charged. Replace the battery, refer to
page 72.'xInterference of the radio connection from
transmission towers or other equipment with
high transmitting power.'xShielding of the remote control due to metal objects.
Do not transport the remote control together
with metal objects.'xInterference of the radio connection from moj
bile phones or other electronic devices in dij
rect proximity to the remote control.
Do not transport the remote control together
with electronic devices.
Wet or snowy conditions may disrupt the locking
request recognition function on the door hanj
dles.
Seite 770pening
and
closingCONTROLS77
Online Edition for Part no. 01402989120 - II/18

In the case of a malfunction, unlock and lock thevehicle using the buttons of the remote control
or using the integrated key, refer to page 73.
Tailgate
General
information To avoid locking it in the vehicle, do not place the
remote control in the cargo area.
Depending on the vehicle equipment and counj
try version, it is possible to specify whether the
doors are also unlocked when unlocking with the
remote control. Adjusting the settings, refer to
page 81.
The tailgate can only be opened if it is not locked. Separately lock the tailgate, refer topage 79.
Safety
information
WARNING
Body parts can be jammed when operating the tailgate. There is a risk of injury. Make sure thatthe area of movement of the tailgate is clear
during opening and closing.
NOTE
During opening, the tailgate pivots back and up.
There is a risk of damage to property. Make
sure that the area of movement of the tailgate
is clear during opening and closing.
Opening
and
closing
Opening
from
the
outside'xWithout Comfort Access: unlock vehicle.
With Comfort Access: unlock the vehicle or
have the remote control with you.
Press button on the tailgate.'xPress button on the remote control
for approx. 1 second.
Depending on the setting, the doors may also be unlocked. Unlocking with the remote conj
trol, refer to page 71.
Opening
from
the
inside
With the vehicle stationary, press the
button in the driver's floor area.
Closing
Grasp the recess grip and pull tailgate down.
Seite 78CONTROLS0pening
and
closing78
Online Edition for Part no. 01402989120 - II/18

Locking
separatelyGeneral
information
The switch in the glove compartment decouples
the tailgate from the central locking system, so it
can no longer be opened.
If the glove compartment is locked with the
integrated key, the remote control can be
handed over without the integrated key, for inj
stance to a valet parking service. It is then no lonj ger possible for objects to be removed from thecargo area even with the remote control.
Securing'xTailgate secured, arrow 1.'xTailgate not secured, arrow 2.
Slide the switch into the desired position.
Trunk
emergency
unlocking
Pull the handle inside the cargo area. The tailgate unlocks.
Driver
profile
Concept In the driver profiles, individual settings for sevj
eral drivers can be stored and called up again when required.
General
information
There are three driver profiles with which perj
sonal vehicle settings can be stored. Every rej mote control has one of these driver profiles asj
signed.
If the vehicle is unlocked using a remote control, the assigned personal driver profile will be actij vated. All settings stored in the driver profile areautomatically applied.
If several drivers use their own remote control, the vehicle will adjust the personal settings durj
ing unlocking. These settings are also restored, if
the vehicle has been used in the meantime by a person with a different remote control.
Changes to the settings are automatically stored
in the driver profile currently activated.
If another driver profile is selected via iDrive, the settings stored in it will be applied automatically.The new driver profile is assigned to the remotecontrol currently used.
There is an additional guest profile available that
is not assigned to any remote control. It can be
used to apply settings in the vehicle without
changing the personal driver profiles.
Functional
requirements
For the system to be able to identify the driver
profile associated to a particular driver, the dej
tected remote control must be clearly allocated
to the driver.
This is the case when:'xThe driver is only carrying his or her own rej
mote control.'xThe driver unlocks the vehicle.'xThe driver gets into the vehicle through the
driver's door.
Settings
The settings for the following systems and funcj
tions are stored in the active profile. The scope of storable settings depends on country and
equipment.
Seite 790pening
and
closingCONTROLS79
Online Edition for Part no. 01402989120 - II/18

'xUnlocking and locking.'xLights.'xClimate control.'xRadio.'xInstrument cluster.'xProgrammable memory buttons.'xVolumes, tone.'xControl Display.'xNavigation.'xPDC Park Distance Control.'xRearview camera.'xSide View.'xTop View.'xHead-up Display.'xDriving Dynamics Control.'xSeat position, exterior mirror position, steerj
ing wheel position where applicable.
Both the positions saved via the seat memory and the last position set are saved.'xIntelligent Safety.'xActive Blind Spot Detection.
Profile
management
Selecting
a
driver
profile
Regardless of the remote control in use, a differj
ent driver profile may be activated. This allows
you to call up personal vehicle settings, even if
you did not unlock the vehicle with your own rej
mote control.
Via iDrive:
1."My Vehicle"2."Driver profiles"3.Select driver profile.4."OK"'xAll settings stored in the called-up driver proj file are automatically applied.'xThe called-up driver profile is assigned to the
remote control being used at the time.'xIf the driver profile is already assigned to a difj ferent remote control, this driver profile willapply to both remote controls.
Using
a
guest
profile
The guest profile is for individual settings that are
stored in none of the three personal driver proj
files.
Via iDrive:
1."My Vehicle"2."Driver profiles"3."Drive off (guest)"4."OK"
The guest profile cannot be renamed. It is not assigned to the current remote control.
Renaming
a
driver
profile
A personal name can be assigned to the active
driver profile to avoid confusion between the
driver profiles.
Via iDrive:
1."My Vehicle"2."Driver profiles"3.Select driver profile.
The driver profile marked with this symbol
can be renamed.
4."Change driver profile name"5.Enter profile name.6. Select the symbol.
Resetting
a
driver
profile
The settings of the driver profile currently in use
are reset to their factory settings.
Via iDrive:
1."My Vehicle"2."Driver profiles"3.Select driver profile.Seite 80CONTROLS0pening
and
closing80
Online Edition for Part no. 01402989120 - II/18