BMW 5 SERIES 2018 Owners Manual

Before
installing
LATCH
child
restraint
fixing
systems
Pull the safety belt away from the area of the
child restraint system.
Assembly
of
LATCH
childrestraint
fixing
systems1.Install child restraint system, see manufacturj
er's information.2.Ensure that both LATCH anchors are propj erly connected.
Child
restraint
systems
with
tether
strap
Safety
information
WARNING
If the upper retaining strap is incorrectly used for the child restraint system, the protective efj
fect can be reduced. There is a risk of injury.
Make sure that the upper retaining strap is not
guided across sharp edges and without twistj
ing to the upper retaining strap.
WARNING
If the rear backrest is not locked, the protective
effect of the child restraint system is limited or
there is none. In particular situations, for inj
stance braking maneuvers or in case of an accij
dent, the rear backrest can fold forward. There
is a risk of injuries or danger to life. Make sure
that the rear backrests are locked.
NOTE
The anchors for the upper retaining straps of
child restraint systems are only provided for
these retaining straps. When other objects are mounted, the anchors can be damaged. Thereis a risk of damage to property. Only mount
child restraint systems to the upper retainingstraps.
Anchors The respective symbol shows the anchorfor the upper retaining strap. Seats withan upper top tether are marked with this
symbol. It can be found on the rear seat backrest or the rear window shelf.
Routing
the
retaining
strap1Direction of travel2Head restraint3Hook for upper retaining strap4Anchor5Rear window shelf6Seat backrest7Upper retaining strap
Attaching
the
upper
retaining
strap
to
the
anchor
1.Open the anchor cover.2.Raise the head restraint.3.Guide the upper retaining strap between the
supports or along both sides of the head rej
straint to the anchor.
For the middle seat, guide it over or along
both sides of the head restraint to the anchor where applicable.4.Attach the hook of the retaining strap to the
anchor.Seite 121Transporting
children
safelyCONTROLS121
Online Edition for Part no. 01402989478 - II/18

5.Tighten the retaining strap by pulling it down.6.Lower and lock head restraints as needed.
Locking
the
doors
andwindows
in
the
rear
General
information In certain situations it may be advisable to securethe rear doors and windows, for instance when
transporting children.
Doors
Push the locking lever on the rear doors up.The door can now be opened from the outside
only.
Safety
switch
for
the
rear Press button on the driver's door.
This locks various functions so that they cannot
be operated from the rear. Safety switch, refer to
page 101.
Seite 122CONTROLSTransporting
children
safely122
Online Edition for Part no. 01402989478 - II/18

DrivingVehicle
features
andoptions
This chapter describes all standard, country-spejcific and optional features offered with the series. It also describes features that are not necessarilyavailable in your vehicle, e. g., due to the selectedoptions or country versions. This also applies to
safety-related functions and systems. When usj
ing these functions and systems, the applicable laws and regulations must be observed.
Start/Stop
button
Concept Pressing the Start/Stop buttonswitches drive-ready state on or
off, refer to page 41.
Steptronic transmission: the drive-ready state is switched on
when you depress the brake pedal while pressj
ing the Start/Stop button.
Pressing the Start/Stop button again switches
drive-ready state back off and standby state, rej
fer to page 41, is switched back on.
Drive-ready
state
Safety
information
DANGER
If the exhaust pipe is blocked or ventilation is inj
sufficient, harmful exhaust gases can enter into the vehicle. The exhaust gases contain polluj
tants which are colorless and odorless. In enj
closed areas, exhaust gases can also accumuj
late outside of the vehicle. There is danger to
life. Keep the exhaust pipe free and ensure sufj
ficient ventilation.
WARNING
An unsecured vehicle can begin to move and
possibly roll away. There is a risk of an accident.
Before exiting, secure the vehicle against rollj
ing.
In order to ensure that the vehicle is secured against rolling away, follow the following:
'xSet the parking brake.'xOn uphill grades or on a downhill slope,
turn the front wheels in the direction of the
curb.'xOn uphill grades or on a downhill slope,
also secure the vehicle, for instance with a
wheel chock.
NOTE
In the case of repeated starting attempts or rej peated starting in quick succession, the fuel is
not burned or is inadequately burned. The cataj
lytic converter can overheat. There is a risk of
damage to property. Avoid repeated starting in quick succession.
Switching
on
drive-ready
state
Steptronic
transmission
1.Depress the brake pedal.2.Press the Start/Stop button.
The ignition is activated automatically for a brief
time and is stopped as soon as the engine starts.
Most of the indicator/warning lights in the instruj
ment cluster light up for a varied length of time.
Seite 123DrivingCONTROLS123
Online Edition for Part no. 01402989478 - II/18

Diesel
engineIf the engine is cold and temperatures are below
approx. 32 

The display indicates that the
conditions for an automatic enj
gine stop have not been met.
Total
time
with
switched-off
engine ECO PRO, refer to page 282,
driving mode: depending on the vehicle equipment, the total timethat the engine has been
switched off using the Auto Start/
Stop function is displayed on an automatic enj
gine stop.
The total time is automatically reset every time
the vehicle is refueled.
Functional
limitationsThe engine is not switched off automatically in
the following situations:'xIn case of a steep downhill grade.'xBrake not engaged strongly enough.'xThe external temperature is high and autoj
matic climate control is running.'xThe car's interior has not yet been heated or cooled to the required level.'xWhere there is a risk of window condensation
when the automatic climate control is
switched on.'xEngine or other parts not at operating temj perature.'xEngine cooling is required.'xThe wheels are at a sharp angle or the steerjing wheel is being turned.'xVehicle battery is heavily discharged.'xAt higher elevations.'xThe hood is unlocked.'xThe parking assistant is activated.'xStop-and-go traffic.'xSteptronic transmission: selector lever posijtion in N or R.'xAfter driving in reverse.'xUse of fuel with high ethanol content.
Starting
the
engine
Functional
requirements Steptronic
transmission
The engine starts automatically under the followj
ing preconditions:
'xBy releasing the brake pedal.'xWhen Automatic Hold is activated: press the accelerator pedal.
Driving
away
After the engine starts, accelerate as usual.
Safety
mode
After the engine switches off automatically, it will not start again automatically if any one of the folj
lowing conditions are met:
'xThe driver's safety belt is unbuckled and the
driver's door is open.'xThe hood was unlocked.
Some indicator lights light up for a varied length of time.
The engine can only be started via the Start/Stop
button.
System
limits
Even if driving off was not intended, the deactij vated engine starts up automatically in the foljlowing situations:
'xExcessive warming of the car's interior when
the air conditioning is switched on.'xExcessive cooling of the car's interior when
the heating is switched on.'xWhere there is a risk of window condensation
when the automatic climate control is
switched on.'xThe steering wheel is turned.Seite 125DrivingCONTROLS125
Online Edition for Part no. 01402989478 - II/18

'xSteptronic transmission:
Change from selector lever position D to N or
R.'xSteptronic transmission:
Change from selector lever position P to N, D, or R.'xVehicle battery is heavily discharged.'xStart of an oil level measurement.
Intelligent
Auto
Start/Stop
function
Depending on the vehicle equipment and counj
try-specific version, the vehicle features a variety of sensors for assessing the traffic situation. The
Intelligent Auto Start/Stop function uses this inj formation to adapt to various traffic situations in aproactive manner.
For instance, this applies to the following situaj
tions:
'xIf a situation is detected in which the stopping time is expected to be very short, the engine
is not switched off automatically. A message
appears on the Control Display, depending on the situation.'xIf a situation is detected in which the vehicle
needs to drive off immediately, the engine is started automatically.
The function may be restricted if the navigation
data is invalid, outdated or not available, for exj
ample.
Activating/deactivating
the
system
manually
Concept
The engine is not automatically switched off.
The engine is started during an automatic engine
stop.
Using
the
button
Press button.
Steptronic
transmission:
via
selector
lever
position
The Auto Start/Stop function is also deactivated in selector lever position M/S.
Via
the
Driving
Dynamics
Control The Auto Start/Stop function is also deactivatedin SPORT driving mode of the Driving DynamicsControl.
Display
'xLED comes on: auto Start/Stop function is
deactivated.'xLED goes out: auto Start/Stop function is acj tivated.
Switching
off
the
vehicle
during
an
automatic
engine
stop
General
information
During an automatic engine stop, the vehicle can be switched off permanently, for instance when
leaving it.
Steptronic
transmission
1.Press the Start/Stop button.'xDrive-ready state is switched off.'xStandby state is switched on.Seite 126CONTROLSDriving126
Online Edition for Part no. 01402989478 - II/18

'xSelector lever position P is engaged autojmatically.2.Set the parking brake.
Automatic
deactivation
General
information
In certain situations, the Auto Start/Stop function
is deactivated automatically for safety reasons,
for instance if no driver is detected.
Malfunction
The Auto Start/Stop function no longer switches off the engine automatically. A Check Control message is displayed. It is possible to continuedriving. Have the system checked by a dealerssservice center or another qualified service centeror repair shop.
Parking
brake
Concept
The parking brake is used to prevent the vehicle
from rolling when it is parked.
Safety
information
WARNING
An unsecured vehicle can begin to move and possibly roll away. There is a risk of an accident.
Before exiting, secure the vehicle against rollj
ing.
In order to ensure that the vehicle is secured against rolling away, follow the following:
'xSet the parking brake.'xOn uphill grades or on a downhill slope,
turn the front wheels in the direction of the curb.'xOn uphill grades or on a downhill slope,also secure the vehicle, for instance with a
wheel chock.
WARNING
Unattended children or animals can cause the
vehicle to move and endanger themselves and
traffic, for instance due to the following actions:
'xPressing the Start/Stop button.'xReleasing the parking brake.'xOpening and closing the doors or winj
dows.'xEngaging selector lever position N.'xUsing vehicle equipment.
There is a risk of accidents or injuries. Do not
leave children or animals unattended in the vej hicle. Take the remote control with you when
exiting and lock the vehicle.
Overview
Parking brake
Setting
With
a
stationary
vehicle Pull the switch.
The LED lights up.
The indicator light in the instrument clusj
ter illuminates red. The parking brake is
set.
While
driving
To use as emergency brake while driving:
Seite 127DrivingCONTROLS127
Online Edition for Part no. 01402989478 - II/18

Pull the switch and hold it. The vehicle brakes
hard while the switch is being pulled.
The indicator light in the instrument clusjter illuminates red, a signal sounds, andthe brake lights illuminate.
A Check Control message is displayed.
If the vehicle is slowed down to a speed of apj
prox. 2 mph/3 km/h the parking brake is set.
Releasing Releasing
manually1.Switch on drive-ready state.2. Steptronic transmission: press the
switch while the brake is pressed or selector
lever position P is set.
The LED and indicator light go out.
The parking brake is released.
Automatic
release The parking brake is released automatically
when you drive away.
The LED and indicator light go out.
Automatic
Hold
Concept This system assists the driver by automatically
setting and releasing the brake, such as when
moving in stop-and-go traffic.
The vehicle is automatically held in place when it
is stationary.
On uphill grades the system prevents the vehicle from rolling backward when driving offf.
General
information Under the following conditions, the parking brake
is automatically engaged:
'xDrive-ready state is switched off.'xThe driver's door is opened while the vehicle
is stationary.'xThe moving vehicle is brought to a standstill
using the parking brake.
Display
The indicator light changes from green
to red.
Safety
information
WARNING
An unsecured vehicle can begin to move and
possibly roll away. There is a risk of an accident.
Before exiting, secure the vehicle against rollj
ing.
In order to ensure that the vehicle is secured against rolling away, follow the following:
'xSet the parking brake.'xOn uphill grades or on a downhill slope,
turn the front wheels in the direction of the curb.'xOn uphill grades or on a downhill slope,also secure the vehicle, for instance with a
wheel chock.
WARNING
Unattended children or animals can cause the
vehicle to move and endanger themselves and
traffic, for instance due to the following actions:
'xPressing the Start/Stop button.'xReleasing the parking brake.'xOpening and closing the doors or winj
dows.'xEngaging selector lever position N.'xUsing vehicle equipment.Seite 128CONTROLSDriving128
Online Edition for Part no. 01402989478 - II/18

There is a risk of accidents or injuries. Do not
leave children or animals unattended in the vej hicle. Take the remote control with you whenexiting and lock the vehicle.
NOTE
If the vehicle is stationary, Automatic Hold enj
gages the parking brake and prevents the vehij
cle from rolling in a vehicle wash. There is a risk
of damage to property. Deactivate Automatic
Hold prior to entering the vehicle wash.
Overview
Automatic Hold
Establishing
function
readiness
of
Automatic
Hold
1.Switch on drive-ready state.2. Press button.
The LED lights up.
The indicator light lights up green.
Automatic Hold is functional. After every new vehicle start, the last sej
lected setting is active.
Automatic
Hold
holding
the
vehicle
Function readiness is established and the drivj er's door is closed.
After stepping on the brake pedal, for instancewhen stopping at a traffic light, the vehicle is auj
tomatically secured against rolling.
The indicator light lights up green.
Driving
away
Step on the accelerator pedal to drive off.
The brake is released automatically and the indij
cator light is no longer illuminated.
Activating
the
parking
brake
automatically
The parking brake is automatically set if drive- ready state is switched off while the vehicle is
being held by Automatic Hold or if the vehicle is
exited.
The indicator light changes from green
to red.
The parking brake is not set automatically, if the
drive-ready state is switched off, while the vehij
cle is coasting to a halt. Automatic Hold is deactij
vated.
Switching
function
readiness
off Press button.
The LED goes out.
The indicator light goes out.
Automatic Hold is switched off.
If the vehicle is being held by Automatic Hold,
press additionally on the brake pedal, when
switching off.
Malfunction
In the event of a failure or malfunction of the
parking brake:Seite 129DrivingCONTROLS129
Online Edition for Part no. 01402989478 - II/18

Secure the vehicle against rolling away, for inj
stance with a wheel chock, after existing the vej
hicle.
After
a
power
failure
To reestablish parking brake functionality after a power failure:1.Switch on standby state.2. Pull the switch while stepping on the
brake pedal or selector lever position P is set
and then push.
This process may take a few seconds. Any
sounds associated with this are normal.
The indicator light is no longer illumij
nated as soon as the parking brake is
ready for operation again.
Turn
signal,
high
beams, headlight
flasher
Turn
signal
Turn
signal
in
exterior
mirror
When driving and during operation of the turn
signals or hazard warning system, do not fold in the exterior mirrors, so that the signal lights on
the exterior mirror are easy to see.
Using
turn
signals
Press the lever past the resistance point.
Triple
turn
signal
activationLightly tap the lever up or down.
The triple turn signal duration can be adjusted.
Via iDrive:1."My Vehicle"2."Vehicle settings"3."Lighting"4."Exterior lighting"5."One-touch turn signal"6.Select the desired setting.
The setting is stored for the driver profile curj
rently used.
Signaling
briefly
Press the lever to the resistance point and hold it there for as long as you want the turn signal to
flash.
High
beams,
headlight
flasher Push the lever forward or pull it backward.
'xHigh beams on, arrow 1.'xHigh beams off/headlight flasher, arrow 2.
Washer/wiper
system
General
information
Do not use the wipers if the windshield is dry, as
this may damage the wiper blades or cause them to become worn more quickly.
Seite 130CONTROLSDriving130
Online Edition for Part no. 01402989478 - II/18