BMW M2 2017 Service Manual

Closing
Grasp the recess grip and pull tailgate down.
Locking
separately The tailgate can be locked separately using the
switch in the glove compartment. If the glove compartment is locked, the tailgate cannot beopened.
'yTailgate secured, arrow 1.'yTailgate not secured, arj
row 2.
Slide the switch into the arrow 1 position. The tailgate is secured and disconnected from the
central locking system.
This is beneficial when the vehicle is parked using valet service. The remote control can behanded out without the integrated key.
Emergency
unlocking
Pull the handle inside the cargo area.
The tailgate unlocks.
Personal
Profile
Concept
Using Personal Profile, individual settings for
several drivers can be saved and called up again at a later time.
General
information
There are three driver profiles with which perj
sonal vehicle settings can be stored. Every rej
mote control has one of these driver profiles
assigned.
If the vehicle is unlocked using a remote conj
trol, the assigned personal driver profile will be
activated. All settings stored in the driver proj
file are automatically applied.
If several drivers use their own remote control,
the vehicle will adjust the personal settings
during unlocking. These settings are also rej
stored, if the vehicle has been used in the
meantime by a person with a different remote
control.
Changes to the settings are automatically
saved in the driver profile currently activated.
If another driver profile is selected via iDrive,
the settings saved in it will be applied automatj
ically. The new driver profile is assigned to the
remote control currently used.
There is an additional profile available that is
not assigned to any remote control: It can be
used to apply settings in the vehicle without
changing the personal driver profiles.
Settings The settings for the following systems and
functions are saved in the active profile. The
scope of storable settings depends on country
and equipment.'yUnlocking and locking.'yLights.'yClimate control.'yRadio.'yInstrument cluster.Seite 41Opening
and
closingControls41
Online Edition for Part no. 01 40 2 974 681 - VI/16

'yProgrammable memory buttons.'yVolumes, tone.'yControl Display.'yNavigation.'yPark Distance Control PDC.'yRearview camera.'yDriving Dynamics Control.'yDriver's seat position, exterior mirror posijtion, steering wheel position.'yIntelligent Safety.
Profile
management
Opening
profiles Regardless of the remote control in use, a difjferent profile may be activated. This allows youto call up personal vehicle settings if you did
not unlock the vehicle with your own key.
Via iDrive:
1."Settings"2."Profiles"3.Select a profile.'yAll settings stored in the called-up profileare automatically applied.'yThe called-up profile is assigned to the rejmote control being used at the time.'yIf the profile is already assigned to a differjent remote control, this profile will apply toboth remote controls.
Using
the
guest
profile
The guest profile is for individual settings that are saved in none of the three personal proj
files.
This can be useful for drivers who are using
the vehicle temporarily and do not have their
own profile.
On the Control Display:
1."Settings"2."Profiles"3."Guest"
The guest profile cannot be renamed. It is not assigned to the current remote control.
Renaming
profiles A personal name can be assigned to every projfile to avoid confusion between the profiles.
On the Control Display:
1."Settings"2."Profiles"3.Open "Options".4."Rename current profile"
Reset
profiles
The settings of the active profile are reset to
their factory settings.
On the Control Display:
1."Settings"2."Profiles"3.Open "Options".4."Reset current profile"
Exporting
profiles Most settings of the active profile can be exjported.
This can be helpful for saving and retrieving
personal settings, e.g., before delivering the
vehicle to a workshop. Profiles can be taken to another vehicle equipped with the Personal
Profile function.
On the Control Display:
1."Settings"2."Profiles"3."Export profile"4.BMW Online: "BMW Online"
USB interface: "USB device"
Popular file systems for USB media are supj
ported. FAT32 and exFAT are the recomj
mended formats for profile export. Other forj
mats may not support the export.
Seite 42ControlsOpening
and
closing42
Online Edition for Part no. 01 40 2 974 681 - VI/16

Importing
profiles
Profiles exported via BMW Online can also be imported via BMW Online.
Profiles stored on a USB storage device can be
imported via the USB interface.
Existing settings are overwritten with the imj
ported profile.
On the Control Display:1."Settings"2."Profiles"3."Import profile"4.BMW Online: "BMW Online"
USB interface: "USB device"
Display
profile
list
during
start
The profile list can be displayed during each
start to select the desired profile.
On the Control Display:
1."Settings"2."Profiles"3.Open "Options".4."Display user list at startup"
Settings
General
information
Depending on the equipment and country-
specific variant of your vehicle, different openj ing and closing settings are available.
These settings are saved in the active driver profile, refer to page 41.
Unlocking
Doors
1."Settings"2."Doors/key"3. Select the symbol.4.Select the desired function:'y"Driver's door only"
Only the driver's door and the fuel filler
flap are unlocked. Pressing again unj locks the entire vehicle.'y"All doors"
The entire vehicle is unlocked.
Tailgate
1."Settings"2."Doors/key"3. Select the symbol.4.Select the desired function:'y"Tailgate"
The tailgate unlocks.'y"Tailgate + door(s)"
The tailgate and the doors are unj
locked.
Confirmation
signals
from
the
vehicle
1."Settings"2."Doors/key"3.Deactivate or activate the desired confirj mation signals.'yWith alarm system:
"Acoustic sig. lock/unlock"
Unlocking is signaled by one honk of the horn.'y"Flash when lock/unlock"
Unlocking is signaled by two flashes,
locking by one.
Automatic
locking
1."Settings"2."Doors/key"3.Select the desired function:'y"Lock if no door is opened"
The vehicle locks automatically after a
short period of time if no door is
opened after unlocking.'y"Lock after start driving"Seite 43Opening
and
closingControls43
Online Edition for Part no. 01 40 2 974 681 - VI/16

The vehicle locks automatically afteryou drive off.
Adjusting
the
last
seat
and
mirror
position
1."Settings"2."Doors/key"3."Last seat position autom."
When the vehicle is unlocked, the driver's seat
and exterior mirrors resume their last set posij tions.
Alarm
system General
information
When the vehicle is locked, the vehicle alarm system reacts to the following changes:
'yUnauthorized opening of a door, the hood
or the tailgate.'yMovements in the interior.'yChanges in the vehicle tilt, e. g., during atj tempts at stealing a wheel or when towing
the vehicle.'yDisconnected battery voltage.
The alarm system signals these changes visuj
ally and acoustically:
'yAcoustic alarm.'yBy switching on the hazard warning sysj tem.'yBy flashing the daytime running lights.
Switching
on
and
off
When you lock and unlock the vehicle with the
remote control or with Comfort Access, the alarm system is switched on and off at thesame time.
Door
lock
with
the
alarm
system
switched
on
The alarm system is triggered when the door is
opened, if the vehicle has been unlocked via
the door lock.
Switching off the alarm, refer to page 45.
Tailgate
with
the
alarm
system
switched
on
The tailgate can be opened even when thealarm system is switched on.
After the tailgate is closed, it is locked and
monitored again provided the doors are
locked. The hazard warning system flashes
once.
Panic
mode You can trigger the alarm system if you find
yourself in a dangerous situation.
Press button on the remote control forat least 3 seconds.
To switch off the alarm: press any button.
Indicator
lamp
on
the
interior
mirror'yThe indicator lamp flashes briefly every
2 seconds:
The alarm system is switched on.'yIndicator lamp flashes for approx. 10 secj onds, then it flashes briefly every 2 secj
onds:
Interior motion sensor and tilt alarm sensor
are not active, as doors, hood, or tailgateSeite 44ControlsOpening
and
closing44
Online Edition for Part no. 01 40 2 974 681 - VI/16

are not correctly closed. Correctly closedaccess points are secured.
When the still open access points are
closed, interior motion sensor and tilt alarm sensor will be switched on.'yThe indicator lamp goes out after unlockj
ing:
The vehicle has not been tampered with.'yThe indicator lamp flashes after unlocking
until the engine ignition is switched on, but no longer than approx. 5 minutes:
An alarm has been triggered.
Tilt
alarm
sensor The tilt of the vehicle is monitored.
The alarm system responds in situations such
as attempts to steal a wheel or when the vehij
cle is towed.
Interior
motion
sensor
The windows and the glass sunroof must be
closed for the system to function properly.
Avoiding
unintentional
alarms
General
information
The tilt alarm sensor and interior motion senj
sor can trigger an alarm, although no unauthorj ized action occurred.
Possible situations for an unwanted alarm:
'yIn automatic vehicle washes.'yIn duplex garages.'yDuring transport on trains carrying vehij
cles, at sea or on a trailer.'yWith animals in the vehicle.
The tilt alarm sensor and the interior motion sensor can be switched off in such situations.
Switching
off
the
tilt
alarm
sensor
and
interior
motion
sensor
Press the remote control button again
within 10 seconds as soon as the vehicle
is locked.
The indicator lamp lights up for approx. 2 secj
onds and then continues to flash.
The tilt alarm sensor and interior motion senj
sor are turned off until the vehicle is locked
again.
Switching
off
the
alarm'yUnlock the vehicle with the remote control or switch on the ignition, if needed through
emergency detection of remote control, rej fer to page 36.'yWith Comfort Access:
If you are carrying the remote control on
your person, grasp the door handle on the driver's or front passenger door comj
pletely.
Power
windows
Safety
information WARNING
When operating the windows, body parts
and objects can be jammed. There is a risk of injury or risk of property damage. Make surethat the area of movement of the windows isclear during opening and closing.'

'yEngaging selector lever position N.'yUsing vehicle equipment.
There is a risk of accidents or injuries. Do notleave children or animals unattended in the vej
hicle. Take the remote control with you when exiting and lock the vehicle.'

The glass sunroof is operational when the ignij
tion is switched on.
Safety
information WARNING
Body parts can be jammed when operatj
ing the glass sunroof. There is a risk of injury.
Make sure that the area of movement of the
glass sunroof is clear during opening and closj
ing.'

Pinch
protection
system
General
information
If the closing force when closing the glass sunj
roof exceeds a certain value, the closing movej ment is stopped, beginning at approximately
the middle of the opening in the roof, or from
the tilted position during closing. The glass
sunroof reopens slightly.
Closing
from
the
open
position
without
pinch
protection
If there is an external danger, proceed as folj
lows:1.Press the switch forward beyond the rej
sistance point and hold.
The pinch protection is limited and the
glass sunroof reopens slightly if the closing
force exceeds a certain threshold.2.Press the switch forward again beyond the resistance point and hold until the glass
sunroof closes without jam protection. Make sure that the closing area is clear.
Closing
from
the
raised
position
without
pinch
protection
If there is an external danger,
push the switch forward past the
resistance point and hold it.
The glass sunroof closes withj
out jam protection.
Initializing
after
a
power
interruption
General
information After a power failure during the opening orclosing process, the glass sunroof can only be
operated to a limited extent.
The system can be initialized when the vehicle
is stationary and the engine is running.
During the initialization, the glass sunroof
closes without jam protection.
Make sure that the closing area is clear.
Initializing
the
system Press the switch up and hold ituntil the initialization is comj
plete:
Initialization begins within
15 seconds and is completed
when the glass sunroof is completely closed.Seite 48ControlsOpening
and
closing48
Online Edition for Part no. 01 40 2 974 681 - VI/16

SettingsVehicle
features
and
options
This chapter describes all standard, country- specific and optional features offered with theseries. It also describes features that are notnecessarily available in your vehicle, e. g., due
to the selected options or country versions.
This also applies to safety-related functions
and systems. When using these functions and systems, the applicable country provisions
must be observed.
Sitting
safely
An ideal seating position that meets the needs
of the occupants can make a vital contribution to relaxed, fatigue-free driving.
The seating position also plays an important role in an accident in combination with:'ySafety belts, refer to page 53.'yHead restraints, refer to page 54.'yAirbags.
Seats
Safety
information WARNING
Seat adjustments while driving can lead
to unexpected movements of the seat. Vehicle
control could be lost. There is a risk of an accij dent. Only adjust the seat on the driver's sidewhen the vehicle is stationary.'

Forward/backward
Pull the lever and slide the seat in the desireddirection.
After releasing the lever, move the seat forj
ward or back slightly making sure it engages
properly.
Height
Pull the lever and apply your weight to the seat or lift it off, as necessary.
Backrest
tilt
Pull the lever and apply your weight to the
backrest or lift it off, as necessary.
Seat
tilt
Pull the lever and move the seat to the desired
tilt. After releasing the lever, apply your weight to the seat or lift it off to make sure the seat
engages properly.
Electrically
adjustable
seats
Overview
1Seat and mirror memory2Backrest width3Lumbar support4Backrest tilt5Forward/backward, height, seat tilt
General
information
The seat setting for the driver's seat is stored
for the profile currently used. When the vehicle
is unlocked via the remote control, the position
is automatically retrieved if the function is actij vated for this purpose.
Seite 50ControlsSettings50
Online Edition for Part no. 01 40 2 974 681 - VI/16