BMW M2 2018 Owners Manual

5Rear window shelf6Seat backrest7Upper retaining strap
Attaching
the
upper
retaining
strap
to
the
anchor
1.Remove the anchor cover.2.Raise the head restraint.3.Guide the upper retaining strap between or
along both sides of the supports of the head restraint to the anchor.4.Attach the hook of the retaining strap to the
anchor.5.Tighten the retaining strap by pulling it down.6.Lower and lock head restraints as needed.Seite 101Transporting
children
safelyCONTROLS101
Online Edition for Part no. 01402662591 - II/18

DrivingVehicle
features
andoptions
This chapter describes all standard, country-spejcific and optional features offered with the series. It also describes features that are not necessarilyavailable in your vehicle, e. g., due to the selectedoptions or country versions. This also applies to
safety-related functions and systems. When usj
ing these functions and systems, the applicable laws and regulations must be observed.
Start/Stop
button
Concept Pressing the Start/Stop buttonswitches the ignition on or off and starts the engine.
M double-clutch transmission: theengine starts with the brake pedal
pressed when you press the Start/Stop button.
Manual transmission: the engine starts with the clutch pedal pressed when the Start/Stop buttonis pressed.
Ignition
on M double-clutch transmission: press the Start/
Stop button, and do not press on the brake pedal
at the same time.
Manual transmission: press the Start/Stop button
without stepping on the clutch pedal.
All vehicle systems are ready for operation. Most of the indicator/warning lights in the instruj
ment cluster light up for a varied length of time.
To save battery power when the engine is off,
switch off the ignition and any unnecessary elecj
tronic systems/power consumers.
Ignition
off
M double-clutch transmission: press the Start/ Stop button again without stepping on the brake.
Manual transmission: press the Start/Stop buttonagain without stepping on the clutch pedal.
All indicator lights in the instrument cluster go out.
To save battery power when the engine is off,
switch off the ignition and any unnecessary elecj
tronic systems/power consumers.
Safety
measures
When switching off the ignition, the transmission
position P is engaged automatically if the selecj
tor lever position D or R is engaged.
The ignition is switched off automatically in the
following situations while the vehicle is stationary
and the engine is off:'xWhen locking the vehicle, and when the low beams are switched on.'xShortly before the battery is discharged comjpletely, so that the engine can still be started.'xWhen opening or closing the driver door, ifthe driver's safety belt is unbuckled and the
low beams are switched off.'xWhile the driver's safety belt is unbuckled
with driver's door open and low beams off.
The low beams switch to parking lights after
some minutes of no use.
Radio-ready
state
General
information In the radio-ready state, certain power consumjers remain ready for operation.
Activating With the engine running, press the Start/Stopbutton.
Seite 102CONTROLSDriving102
Online Edition for Part no. 01402662591 - II/18

If the engine is not running and the ignition isswitched on: the system automatically activates
radio-ready state when the door is opened if the
lights are switched off or the daytime running lights are switched on.
The radio-ready state remains active if, for inj
stance the ignition is automatically switched off
for the following reasons:'xOpening or closing the driver's door.'xUnfastening of the driver's safety belt.'xWhen automatically switching from low beams to parking lights.
Switching
off
automatically
The radio-ready state is switched off automatijcally in the following situations:
'xIf the ignition is switched off manually withthe Start/Stop button.'xAfter approx. 8 minutes.'xWhen the vehicle is locked using the centrallocking system.'xShortly before the battery is discharged comjpletely, so that the engine can still be started.
Starting
the
engine
Safety
information
DANGER
If the exhaust pipe is blocked or ventilation is inj
sufficient, harmful exhaust gases can enter into the vehicle. The exhaust gases contain polluj
tants which are colorless and odorless. In enj
closed areas, exhaust gases can also accumuj
late outside of the vehicle. There is danger to
life. Keep the exhaust pipe free and ensure sufj
ficient ventilation.
WARNING
An unsecured vehicle can begin to move and
possibly roll away. There is a risk of an accident.
Before exiting, secure the vehicle against rollj
ing.
In order to ensure that the vehicle is secured
against rolling away, follow the following:
'xSet the parking brake.'xOn uphill grades or on a downhill slope,
turn the front wheels in the direction of the
curb.'xOn uphill grades or on a downhill slope, also secure the vehicle, for instance with awheel chock.
NOTE
In the case of repeated starting attempts or rej peated starting in quick succession, the fuel is
not burned or is inadequately burned. The cataj
lytic converter can overheat. There is a risk of
damage to property. Avoid repeated starting in quick succession.
M
double-clutch
transmission
Starting
the
engine
1.Depress the brake pedal.2.Press the Start/Stop button.
The ignition is activated automatically for a brief
time and is stopped as soon as the engine starts.
Manual
transmission
Starting
the
engine
1.Depress the brake pedal.2.Press on the clutch pedal and shift to neutral.3.Press the Start/Stop button.
The ignition is activated automatically for a brief
time and is stopped as soon as the engine starts.
Seite 103DrivingCONTROLS103
Online Edition for Part no. 01402662591 - II/18

Engine
stop
Safety
information
WARNING
Unattended children or animals can cause the
vehicle to move and endanger themselves and
traffic, for instance due to the following actions:
'xPressing the Start/Stop button.'xReleasing the parking brake.'xOpening and closing the doors or winj
dows.'xEngaging selector lever position N.'xUsing vehicle equipment.
There is a risk of accidents or injuries. Do not
leave children or animals unattended in the vej hicle. Take the remote control with you whenexiting and lock the vehicle.
WARNING
An unsecured vehicle can begin to move and
possibly roll away. There is a risk of an accident.
Before exiting, secure the vehicle against rollj
ing.
In order to ensure that the vehicle is secured against rolling away, follow the following:
'xSet the parking brake.'xOn uphill grades or on a downhill slope,
turn the front wheels in the direction of the curb.'xOn uphill grades or on a downhill slope,
also secure the vehicle, for instance with a
wheel chock.
M
double-clutch
transmission
Switching
off
the
engine
1.Apply the brakes until the vehicle comes to astop.2.Press the Start/Stop button.
The engine is switched off.
The radio-ready state is switched on.3.Set the parking brake.
Manual
transmission
Switching
off
the
engine
1.With the vehicle at a standstill, press the
Start/Stop button.2.Shift into first gear or reverse.3.Set the parking brake.
Auto
Start/Stop
function
Concept
The Auto Start/Stop function helps save fuel.
The system switches off the engine during a stop, for instance in traffic congestion or at traffic
lights. The ignition remains switched on. The enj
gine starts automatically for driving off.
The Auto Start/Stop function is only available in
the COMFORT or TRACTION driving programs, refer to page 158.
General
information
After every start of the engine using the Start/
Stop button, the Auto Start/Stop function is in the last selected state. When the Auto Start/Stop
function is active, it is available when the vehicle
is traveling faster than about 3 mph/5 km/h.
Engine
stop
Functional
requirements The engine is switched off automatically during a
stop under the following conditions:
M double-clutch transmission:
'xThe selector lever is in selector lever position D.Seite 104CONTROLSDriving104
Online Edition for Part no. 01402662591 - II/18

'xThe brake pedal remains depressed while thevehicle is stopped.'xThe driver's safety belt is buckled or the drivjer's door is closed.
Manual transmission:
'xNeutral is engaged and the clutch pedal isnot pressed.'xThe driver's safety belt is buckled or the drivjer's door is closed.
The air flow from the air conditioner is reduced
when the engine is switched off.
Displays
in
the
instrument
cluster The READY display in the tachjometer signals that the Auto
Start/Stop function is ready to
start the engine automatically.
The display indicates that the
conditions for an automatic enj
gine stop have not been met.
Functional
limitations The engine is not switched off automatically in
situations such as the following:
'xIn case of a steep downhill grade.'xExternal temperature too low.'xThe external temperature is high and autoj
matic climate control is running.'xThe car's interior has not yet been heated or cooled to the required level.'xThe engine is not yet at operating temperaj
ture.'xThe wheels are at a sharp angle or the steerj ing wheel is being turned.'xAfter driving in reverse.'xWhere there is a risk of window condensation
when the automatic climate control is
switched on.'xVehicle battery is heavily discharged.'xAt higher elevations.'xThe hood is unlocked.'xStop-and-go traffic.'xUse of fuel with high ethanol content.
Starting
the
engine
The engine starts automatically under the followj
ing conditions:
'xM double-clutch transmission: by releasing the brake pedal.'xManual transmission: clutch pedal is pressed.
After the engine starts, accelerate as usual.
Safety
mode
After the engine switches off automatically, it will not start again automatically if any one of the folj
lowing conditions are met:
'xThe driver's safety belt is unbuckled and the
driver's door is open.'xThe hood was unlocked.
Some indicator lights light up for a varied length of time.
The engine can only be started via the Start/Stop
button.
Functional
limitations
Even if driving off was not intended, the deactij
vated engine starts up automatically in the folj lowing situations:
'xExcessive warming of the car's interior when
the air conditioning is switched on.'xThe steering wheel is turned.'xDouble-clutch transmission: change from sej lector lever position D to N, R or D/S.'xM double-clutch transmission: accelerating
while simultaneously applying the brake.'xThe vehicle begins rolling.Seite 105DrivingCONTROLS105
Online Edition for Part no. 01402662591 - II/18

'xWhere there is a risk of window condensation
when the automatic climate control is
switched on.'xVehicle battery is heavily discharged.'xExcessive cooling of the car's interior when
the heating is switched on.'xLow brake vacuum pressure; this can occur,
for instance if the brake pedal is depressed a
number of times in succession.
Preventing
an
automatic
engine
stop
with
aM
double-clutch
transmission
Concept
To make it possible to drive off very quickly, such
as at an intersection, the automatic engine stop can be actively prevented.
Preventing
an
engine
stop
using
the
brake
pedal
The engine stop can be actively prevented within one second after the vehicle comes to a standj still:
'xImmediately after the vehicle comes to a
standstill, briefly press the brake pedal forcej fully.'xThen press the brake pedal with normal brakj
ing force.
Activating/deactivating
the
system
manually
Using
the
button
Press button.'xLED comes on: auto Start/Stop function is
deactivated.
The engine is started during an automatic enj
gine stop.
The engine can only be stopped or started
via the Start/Stop button.'xLED goes out: auto Start/Stop function is acj tivated.
Switching
off
the
vehicle
during
an
automatic
engine
stop
During an automatic engine stop, the vehicle canbe switched off permanently, for instance when
leaving it.
M double-clutch transmission:
1.Press the Start/Stop button. The ignition is
switched off. The Auto Start/Stop function is deactivated.
Selector lever position P is engaged automatj ically.2.Set the parking brake.
Manual transmission:
1.Press the Start/Stop button. The ignition is
switched off. The Auto Start/Stop function is deactivated.2.Shift into first gear or reverse.3.Set the parking brake.
Engine start as usual via Start/Stop button.
Automatic
deactivation
In certain situations, the Auto Start/Stop function
is deactivated automatically for safety reasons,
for instance if no driver is detected.
Malfunction
The Auto Start/Stop function no longer switches
off the engine automatically. A Check Control
message is displayed. It is possible to continue
driving. Have the system checked by a dealerss
Seite 106CONTROLSDriving106
Online Edition for Part no. 01402662591 - II/18

service center or another qualified service centeror repair shop.
Parking
brake
Safety
information
WARNING
An unsecured vehicle can begin to move and
possibly roll away. There is a risk of an accident.
Before exiting, secure the vehicle against rollj
ing.
In order to ensure that the vehicle is secured against rolling away, follow the following:
'xSet the parking brake.'xOn uphill grades or on a downhill slope,
turn the front wheels in the direction of the curb.'xOn uphill grades or on a downhill slope,
also secure the vehicle, for instance with a
wheel chock.
Applying
The lever automatically engages after being
pulled up.
The indicator light lights up red. The
parking brake is set.
Lower light: indicator light in Canadian
models
If for once use during driving is required, engage the parking brake slightly and hold the buttondown.
To prevent corrosion and one-sided brake acj tion, lightly apply the parking brake periodically
while coasting, if traffic conditions permit.
The brake lights will not light up if the parking
brake is set.
Releasing
Raise lever slightly, press the button and guide the lever down.
Turn
signal,
high
beams,headlight
flasher
Turn
signal
Turn
signal
in
exterior
mirror When driving and during operation of the turn
signals or hazard warning system, do not fold in
the exterior mirrors, so that the signal lights on
the exterior mirror are easy to see.
Using
turn
signals
Press the lever past the resistance point.
Triple
turn
signal
activation Lightly tap the lever up or down.
The turn signal flashes three times.
The function can be activated or deactivated.
Seite 107DrivingCONTROLS107
Online Edition for Part no. 01402662591 - II/18

Via iDrive:1."My Vehicle"2."Vehicle settings"3."Lighting"4."Exterior lighting"5."One-touch turn signal"6.Select the desired setting.
Settings are stored for the profile currently used.
Signaling
briefly
Press the lever to the resistance point and hold it there for as long as you want the turn signal to
flash.
Malfunction
Unusually rapid flashing of the indicator light indij
cates that a turn signal bulb has failed.
High
beams,
headlight
flasher Push the lever forward or pull it backward.
'xHigh beams on, arrow 1.'xHigh beams off/headlight flasher, arrow 2.
Washer/wiper
system
General
information
Do not use the wipers if the windshield is dry, as
this may damage the wiper blades or cause them to become worn more quickly.
Safety
information
WARNING
If the wipers start moving in the folded away state, body parts can be jammed or damagemay occur to parts of the vehicle. There is a risk
of injury or risk of damage to property. Make
sure that the vehicle is switched off when the wipers are in the folded away state and the wipj
ers are folded in when switching on.
NOTE
If the wipers are frozen to the windshield, the
wiper blades can be torn off and the wiper moj
tor can overheat when switching on. There is a risk of damage to property. Defrost the windj
shield prior to switching the wipers on.
Switching
on
Press the lever up until the desired position is reached.
'xResting position of the wipers, position 0.'xIntermittent operation or rain sensor, posijtion 1.'xNormal wiper speed, position 2.'xFast wiper speed, position 3.
When travel is interrupted with the wiper systemswitched on: when travel continues, the wipers
resume at their previous speed.
Seite 108CONTROLSDriving108
Online Edition for Part no. 01402662591 - II/18

Switching
off
and
brief
wipe
Press the lever down.
'xSwitching off: press the lever down until itreaches its standard position.'xBrief wipe: press the lever down from the
standard position.
The lever automatically returns to its initial position when released.
Interval
mode
or
rain
sensor
Concept
The rain sensor automatically controls the time between wipes depending on the intensity of the rainfall.
General
information The sensor is located on the windshield, directly
in front of the interior mirror. Without the rain
sensor, the frequency of the wiper operation is preset.
Safety
information
NOTE
If the rain sensor is activated, the wipers can
accidentally start moving in vehicle washes. There is a risk of damage to property. Deactij
vate the rain sensor in vehicle washes.
Activating
Press the lever up once from its standard posij tion, arrow 1.
Wiping is started.
The LED in the wiper lever is illuminated.
If wipers are frozen to windshield, wiper operaj
tion is deactivated.
Deactivating
Press the lever back into the standard position.
Setting
the
frequency
or
sensitivity of
the
rain
sensor
Turn the thumbwheel to adjust the frequency orsensitivity of the rain sensor.
Up: short interval or high sensitivity of the rain
sensor.
Down: long interval or low sensitivity of the rain
sensor.
Seite 109DrivingCONTROLS109
Online Edition for Part no. 01402662591 - II/18

Windshield
and
headlight
washer
system
Safety
information
WARNING
The washer fluid can freeze onto the window at
low temperatures and obstruct the view. There
is a risk of an accident. Only use the washer
systems, if the washer fluid cannot freeze. Use
antifreeze, if needed.
NOTE
When the washer fluid reservoir is empty, the
wash pump cannot work as intended. There is a risk of damage to property. Do not use the
washer system when the washer fluid reservoir
is empty.
Cleaning
the
windshield
Pull the lever.
The system sprays washer fluid on the windj shield and activates the wipers briefly.
In addition, the headlights are cleaned at regular
intervals when the vehicle's lights are switched
on.
Windshield
washer
nozzles
The washer jets are automatically heated whenj
ever the ignition is switched on.
Fold-away
position
of
the
wipers
Concept
The fold-out position enables the wipers to be folded away from the windshield.
General
information Important, for instance when changing the wiper
blades or when folding out under frosty condij
tions.
Safety
information
WARNING
If the wipers start moving in the folded away state, body parts can be jammed or damagemay occur to parts of the vehicle. There is a risk
of injury or risk of damage to property. Make
sure that the vehicle is switched off when the wipers are in the folded away state and the wipj
ers are folded in when switching on.
NOTE
If the wipers are frozen to the windshield, the
wiper blades can be torn off and the wiper moj
tor can overheat when switching on. There is a risk of damage to property. Defrost the windj
shield prior to switching the wipers on.
Folding
away
the
wipers
1.Switch the ignition on and off again.Seite 110CONTROLSDriving110
Online Edition for Part no. 01402662591 - II/18