BMW X1 2017 Owners Manual

Switching
offPress and hold the left button until the
control switches off.
Temperature
Concept
The system achieves the set temperature as
quickly as possible and then keeps it constant.
Settings Turn the ring to set the desired
temperature.
Air
conditioning
Concept
The air in the vehicle's interior will be cooled
and dehumidified and, depending on the temj perature setting, warmed again.
The vehicle's interior can only be cooled with the engine running.
Switching
on/off Press button.
Air conditioning is switched on or off.
Depending on the weather, the windshield and
side windows may fog up briefly when the enj
gine is started.
The air conditioner produces condensation water, refer to page 177, that will exit from bej
low the vehicle.
Recirculated-air
modeConcept
You may react to unpleasant odors or polluj
tants in the immediate environment by tempoj rarily suspending the supply of outside air. Thesystem then recirculates the air flow within the
vehicle.
Operation Press button repeatedly to select an
operating mode:'yLED off: outside air flows in continuously.'yLED on, recirculated-air mode: the supply
of outside air into the vehicle is permaj
nently blocked.
To prevent window fogging, recirculated-air
mode switches off automatically after a certain amount of time, depending on the environj
mental conditions.
With constant recirculated-air mode, the air
quality in the vehicle's interior deteriorates and the fogging of the windows increases.
If the windows fog over, switch off recircuj
lated-air mode and increase the air flow, if
needed.
Controlling
the
air
flow
manually
Concept
The air flow for climate control can be adjusted manually.
Operation Press the left or right side of the butj
ton: decrease or increase air flow.
The intensity is indicated by LEDs. The highj
est level is active when seven LEDs are lit.
The air flow from the air conditioner may be rej
duced automatically to save battery power.
Controlling
the
air
distribution
manually
Concept
The air distribution for climate control can be
adjusted manually.
Seite 151Climate
controlControls151
Online Edition for Part no. 01 40 2 974 556 - X/16

OperationTurn the wheel to select the dejsired program or the desired inj
termediate setting.'y Windows.'y Upper body region.'y Floor area.'y Windows, upper body region, and floor
area.
Defrosting
windows
and
removing
condensation
Direct the air distribution toward windows, injcrease the air flow and temperature, and ifneeded, use the cooling function.
Rear
window
defroster
Press button. The LED lights up.The rear window defroster switches
off automatically after a certain period of time.
For permanent activation, press the button for
longer than 3 seconds. To deactivate, press the button again.
Microfilter In external and recirculated-air mode the mij
crofilter filters dust and pollen from the air.
Have this filter changed during vehicle maintej
nance, refer to page 217.
Automatic
climate
control
1Defrosting windows and removing condenj
sation2Temperature, left3AUTO program4Switching off the system5Air flow, AUTO intensity6DisplaySeite 152ControlsClimate
control152
Online Edition for Part no. 01 40 2 974 556 - X/16

7SYNC program8Maximum cooling9Temperature, right10Air conditioning11Automatic recirculated-air control/recircujlated-air mode12Seat heating, right\_ 5513Air distribution settings14Seat heating, left\_5515Interior temperature sensor n always keep
clear16Rear window defrosterClimate
control
functions
in
detail
Switching
the
system
on/off
Switching
on
Press any button except for the following:'ySYNC program.'yRear window defroster.'ySeat heating.
Switching
off
Press button.
Temperature
Concept
The automatic climate control achieves the set
temperature as quickly as possible, if necesj
sary by using the maximum cooling or heating
power, and then keeps it constant.
Settings Turn the ring to set the desired
temperature.
The selected temperature is shown on the disj
play of the automatic climate control.
The automatic climate control reaches this
temperature as quickly as possible, if needed,
by increasing the cooling or heating output,
and then keeps it constant.
Do not rapidly switch between different temj
perature settings. Otherwise, the automatic clij mate control will not have sufficient time to adj
just the set temperature.
Air
conditioning
Concept
The air in the vehicle's interior will be cooled and dehumidified and, depending on the temj
perature setting, warmed again.
The vehicle's interior can only be cooled with
the engine running.
Switching
on/off Press button.
Air conditioning is switched on or off.
Depending on the weather, the windshield and
side windows may fog up briefly when the enj
gine is started.
The cooling function is switched on automatij
cally with the AUTO program.
When using the automatic climate control,
condensation water, refer to page 177, develj
ops and drains underneath the vehicle. This is
normal.
Maximum
coolingConcept
The system is set to the lowest temperature,
optimum air flow and recirculated-air mode.Seite 153Climate
controlControls153
Online Edition for Part no. 01 40 2 974 556 - X/16

General
information
The function is available above an external
temperature of approx. 32 

General
information
To manually adjust air flow turn off AUTO proj
gram first.
Operation Press the left or right side of the butjton: decrease or increase air flow.
The selected air flow is shown on the display of
the automatic climate control.
The air flow of the automatic climate control
may be reduced automatically to save battery
power.
Controlling
the
air
distribution
manually
Concept
The air distribution for climate control can be
adjusted manually.
Operation Press button repeatedly to select a
program:'yUpper body region and floor area.'yFloor area.'yWindows and floor area.'yWindows.'yWindows and upper body region.'yUpper body region.'yWindows, upper body region, and floor
area.
If the windows are fogged over, press the AUTO button to utilize the condensation senj
sor.
SYNC
program
Concept
The system enables the transfer of current
settings on the driver's side for temperature, air flow, air distribution, and the AUTO proj
gram to the front passenger side and to the leftand right rear.
Switching
on/off Press button.
The current setting of the temperature
on the driver's side is transferred to the front
passenger side.
The program is switched off if the setting on
the front passenger side is changed.
Defrosting
windows
and
removing
condensation
Concept
Ice and condensation are quickly removed from the windshield and the front side winj
dows.
Switching
on/off Press button.
The LED is illuminated with the sysj
tem switched on.
For this purpose, point the side vents towards the side windows as needed.
The air flow can be adjusted with the air flow
active.
If the windows are fogged over, you can also
switch on the cooling function or press the AUTO button to utilize the condensation senj
sor.
Rear
window
defroster Press button. The LED lights up.
The rear window defroster switches
off automatically after a certain period of time.
For permanent activation, press the button for
longer than 3 seconds. To deactivate, press the button again.Seite 155Climate
controlControls155
Online Edition for Part no. 01 40 2 974 556 - X/16

Microfilter/activated-charcoal
filter
In external and recirculated-air mode the mij
crofilter/activated charcoal filter filters dust, pollen, and gaseous pollutants out of the air.
Have this filter changed during vehicle maintej
nance, refer to page 217.
Ventilation Front
ventilation'yLever for changing the air flow direction,
arrow 1.'yThumbwheels for opening and closing the
vents continuously, arrows 2.
Settings
'yVentilation for cooling:
Direct vent in your direction when vehicle's interior is too hot.'yDraft-free ventilation:
Adjust the vent to let the air flow past you.Ventilation
in
the
rear'yLever for changing the air flow direction,
arrow 1.'yThumbwheel for variable opening and
closing of the vents, arrow 2.
Parked-vehicle
ventilation
Concept
The parked-vehicle ventilation ventilates the
vehicle interior and lowers its temperature, if needed.
The system can be switched on and off at any external temperature, either directly or by usjing two preset activation times. It remainsswitched on for 30 minutes.
Open the vents to allow air to flow out.
Switching
on/off
directly
On the Control Display:
1."Settings"2."Climate"3."Activate comf. ventilation"
The symbol on the automatic climate conj
trol flashes if the system is switched on.
Preselecting
the
activation
time
Using iDrive:
1."Settings"2."Climate"Seite 156ControlsClimate
control156
Online Edition for Part no. 01 40 2 974 556 - X/16

3."Timer 1:" or "Timer 2:"4.Set the desired time.
Activating
the
activation
timeUsing iDrive:
1."Settings"2."Climate"3."Activate timer 1" or "Activate timer 2"
The symbol on the automatic climate conj
trol lights up when the switch-on time is actij
vated.
The symbol on the automatic climate conj
trol flashes when the system has been switched on.
The system will only be switched on within the
next 24 hours. After that, it needs to be reactij vated.
Seite 157Climate
controlControls157
Online Edition for Part no. 01 40 2 974 556 - X/16

Interior
equipmentVehicle
features
and
optionsThis chapter describes all standard, country-specific and optional features offered with theseries. It also describes features that are notnecessarily available in your vehicle, e. g., due
to the selected options or country versions.
This also applies to safety-related functions
and systems. When using these functions and systems, the applicable laws and regulations
must be observed.
Universal
Integrated
Remote
Control
Concept
The integrated Universal Remote Control in
the interior mirror can operate up to 3 funcj
tions of remote-controlled systems, such as
garage door drives or lighting systems. The Universal Integrated Remote Control replaces
up to 3 different hand-held transmitters. To
operate the remote control, the buttons on the
interior mirror must be programmed with the
desired functions. The hand-held transmitter
for the particular system is required in order to
program the remote control.
Before selling the vehicle, delete the stored
functions for the sake of security.
Safety
information WARNING
Body parts can be jammed when operatj
ing remote-controlled systems, e.g., the gaj
rage door, using the integrated universal rej mote control. There is a risk of injury or risk ofproperty damage. Make sure that the area ofmovement of the respective system is clear
during programming and operation. Also followthe safety instructions of the hand-held transj
mitter.'

proximately 20 seconds until the LED on
the interior mirror flashes. This erases all
programming of the buttons on the interior mirror.3.Hold the hand-held transmitter for the sysjtem to be controlled approx. 1 to 3 inj
ches/2.5 to 8 cm away from the buttons of
the interior mirror. The required distance
depends on the hand-held transmitter.4.Simultaneously press and hold the button
of the desired function on the hand-held transmitter and the button to be programj
med on the interior mirror. The LED on the
interior mirror will begin flashing slowly.5.Release both buttons as soon as the LED flashes more rapidly. The LED flashing
faster indicates that the button on the intej
rior mirror has been programmed.
If the LED does not flash faster after at
least 60 seconds, change the distance bej
tween the interior mirror and the hand-held transmitter and repeat the step. Several
more attempts at different distances may be necessary. Wait at least 15 seconds bej
tween attempts.
Canada: if programming with the hand- held transmitter was interrupted, hold
down the interior mirror button and repeatj
edly press and release the hand-held
transmitter button for 2 seconds.6.To program other functions on other butj
tons, repeat steps 3 to 5.
The systems can be controlled using the intej
rior mirror buttons.
Special
feature
of
the
rolling
code
wireless
system
If you are unable to operate the system after
repeated programming, please check if the system to be controlled features a rolling coderadio system.
Read the system's owner's manual, or press the programmed button on the interior mirror longer. If the LED on the interior mirror starts
flashing rapidly and then stays lit constantly for
2 seconds, the system features a rolling code
radio system. Flashing and continuous illumij
nation of the LED will repeat for approximately
20 seconds.
For systems with a rolling code radio system,
the Universal Integrated Remote Control and the system also have to be synchronized.
Please read the owner's manual to find out
how to synchronize the system.
Synchronizing is easier with the aid of a secj
ond person.
Synchronizing the universal remote control with the system:1.Park the vehicle within range of the rejmote-controlled system.2.Program the desired button on the interiormirror as described.3.Locate and press the synchronizing button
on the system being programmed. You
have approx. 30 seconds for the next step.4.Hold down the programmed button on the
interior mirror for approximately 3 seconds
and then release it. If necessary, repeat this step up to three times in order to finish
synchronization. Once synchronization is
complete, the programmed function will be carried out.
Reprogramming
individual
buttons
1.Switch on the ignition.2.Press and hold the interior mirror button tobe programmed.3.As soon as the interior mirror LED starts
flashing slowly, hold the hand-held transj
mitter for the system to be controlled apj prox. 1 to 3 inches/2.5 to 8 cm away from
the buttons of the interior mirror. The rej
quired distance depends on the hand-held transmitter.Seite 159Interior
equipmentControls159
Online Edition for Part no. 01 40 2 974 556 - X/16

4.Likewise, press and hold the button of the
desired function on the hand-held transj mitter.5.Release both buttons as soon as the intej
rior mirror LED flashes more rapidly. The LED flashing faster indicates that the butj
ton on the interior mirror has been proj
grammed. The system can then be conj
trolled by the button on the interior mirror.
If the LED does not flash faster after at
most 60 seconds, change the distance and
repeat the programming starting with
step 4. Several more attempts at different
distances may be necessary. Wait at least 15 seconds between attempts.
Canada: if programming with the hand-
held transmitter was interrupted, hold
down the interior mirror button and repeatj
edly press and release the hand-held
transmitter button for 2 seconds.
Operation
WARNING
Body parts can be jammed when operatj
ing remote-controlled systems, e.g., the gaj
rage door, using the integrated universal rej
mote control. There is a risk of injury or risk of
property damage. Make sure that the area of movement of the respective system is clear
during programming and operation. Also follow
the safety instructions of the hand-held transj
mitter.'