BMW X1 2018 Owners Manual

MaintenanceVehicle
features
andoptions
This chapter describes all standard, country-spejcific and optional features offered with the series. It also describes features that are not necessarilyavailable in your vehicle, e. g., due to the selectedoptions or country versions. This also applies to
safety-related functions and systems. When usj
ing these functions and systems, the applicable laws and regulations must be observed.
BMW
maintenance
system
The maintenance system indicates required maintenance measures, and thereby providessupport in maintaining road safety and the operajtional reliability of the vehicle.
In some cases, scopes and intervals of the mainj
tenance system may vary according to the counj try version. Replacement work, spare parts, fuels
and lubricants, and wear materials are calculated
separately. Further information is available from a
dealerss service center or another qualified servj
ice center or repair shop.
Condition
Based
ServiceCBS
Concept
Sensors and special algorithms take into account the driving conditions of the vehicle. CBS uses
these to calculate the need for maintenance.
The system makes it possible to adapt the
amount of maintenance corresponding to your
user profile.
General
information
Information on service requirements, refer to
page 135, can be displayed on the Control Disj
play.
Service
data
in
the
remote
control
Information on the required maintenance is conjtinuously stored in the remote control. The dealjerss service center can read this data out and
suggest a maintenance scope for the vehicle.
Therefore, hand the service advisor the remote
control with which the vehicle was driven most recently.
Storage
periods Storage periods during which the vehicle battery
was disconnected are not taken into account.
If this occurs, have a dealer's service center or
another qualified service center or repair shop update the time-dependent maintenance procejdures, such as checking brake fluid and, if necesj
sary, changing the engine oil and the microfilter/ activated-charcoal filter.
Service
and
Warranty Information
Booklet
for
USmodels
and
Warranty
and Service
Guide
Booklet
forCanadian
models
Please consult your Service and Warranty Inforj
mation Booklet for US models and Warranty and Service Guide Booklet for Canadian models for
additional information on service requirements.
The manufacturer of your vehicle recommends
that maintenance and repair be performed by a dealerss service center or another qualified servj
Seite 271MaintenanceMOBILITY271
Online Edition for Part no. 01402120596 - II/18

ice center or repair shop. Records of regular
maintenance and repair work should be retained.
Socket
for
OBD
Onboard Diagnosis
General
information
Devices connected at the OBD socket trigger
the alarm system when the vehicle is locked. Rej move any devices connected at the OBD socket
before locking the vehicle.
Safety
information
NOTE
The socket for Onboard Diagnosis is an intrij
cate component intended to be used in conj
junction with specialized equipment to check
the vehicless primary emissions system. Imj
proper use of the socket for Onboard Diagnoj
sis, or contact with the socket for Onboard Dij
agnosis for other than its intended purpose,
can cause vehicle malfunctions and creates
risks of personal and property damage. Given
the foregoing, the manufacture of your vehicle
strongly recommends that access to the socket
for Onboard Diagnosis be limited to a dealer's
service center or another qualified service cenj
ter or repair shop or other persons that have
the specialized training and equipment for purj
poses of properly utilizing the socket for Onj
board Diagnosis.
Position
There is an OBD socket on the driver's side for checking the primary components in the vehij
cle's emissions.
Emissions
'xThe warning light lights up:
Emissions are deteriorating. Have the vehicle checked as soon as possible.'xThe warning light flashes under certain cirj
cumstances:
This indicates that there is excessive misfiring in the engine.
Reduce the vehicle speed and have the sysj
tem checked immediately; otherwise, serious
engine misfiring within a brief period can serij
ously damage emission control components, in particular the catalytic converter.Seite 272MOBILITYMaintenance272
Online Edition for Part no. 01402120596 - II/18

Replacing
componentsVehicle
features
andoptions
This chapter describes all standard, country-spejcific and optional features offered with the series. It also describes features that are not necessarilyavailable in your vehicle, e. g., due to the selectedoptions or country versions. This also applies to
safety-related functions and systems. When usj
ing these functions and systems, the applicable laws and regulations must be observed.
Onboard
vehicle
tool
kit
The onboard vehicle tool kit is located under the
cargo floor panel.
Wiper
blades
Safety
information
NOTE
The window may sustain damage if the wiper
falls onto it without the wiper blade installed.
There is a risk of damage to property. Hold the wiper firmly when changing the wiper blade. Do
not fold or switch on the wiper without a wiper blade installed.
NOTE
Folded-away wipers can be jammed when the hood is opened. There is a risk of damage to
property. Make sure that the wipers with the wiper blades mounted are folded down onto
the windshield before opening the hood.
Replacing
the
front
wiper
blades
1.To change the wiper blades, move the wipers into their fold-away position, refer to
page 116.2.Fold up and hold the wiper arm firmly.3.Press button, arrow 1, and pull out the wiper
blade.4.Insert the new wiper blade in reverse order of
removal until it locks in place.5.Fold down the wipers.Seite 273Replacing
componentsMOBILITY273
Online Edition for Part no. 01402120596 - II/18

Replacing
the
rear
wiper
blade1.Lift the wiper up fully and pull off the wiperblade, arrow.2.Position the new wiper blade and press it on
until it you hear it snap into place.3.Fold the wipers in.
Light
and
bulb
replacement
General
information
Lights
and
bulbs
Lights and bulbs make an essential contribution
to vehicle safety.
The vehicle manufacturer recommends that you have the relevant work carried out a dealerss service center or another qualified service centeror repair shop.
A spare light box is available from a dealerss servj ice center or another qualified service center or repair shop.
Follow the safety information, refer to page 274.
Light-emitting
diodes
(LEDs) Some items of equipment use light-emitting dijodes installed behind a cover as a light source.
These light-emitting diodes are related to conj
ventional lasers and are officially designated as Class 1 light-emitting diodes.
Follow the safety information, refer to page 274.
Safety
information
Lights
and
bulbs
WARNING
Bulbs can get hot during operation. Contact
with the bulbs can cause burns. There is a risk of injury. Only change bulbs after they have
cooled off.
WARNING
Work on switched-on lighting systems can
cause short circuits. There is a risk of injury or
risk of damage to property. When working on
the lighting system, switch off the lights in
question. If necessary, heed the bulb manufacj
turer's instructions.
NOTE
Dirty bulbs have a reduced service life. There is
a risk of damage to property. Do not hold new bulbs with your bare hands. Use a clean clothor something similar, or hold the bulb by its
base.
Light-emitting
diodes
(LEDs)
WARNING
Intensive brightness can irritate or damage the
retina of the eye. There is a risk of injury. Do not look directly into the headlights or other lightsources. Do not remove the LED covers.
Headlight
glass
Condensation can form on the inside of the exjternal lights in cool or humid weather. When drivj
ing with the lights switched on, the condensation evaporates after a short time. The headlight
glass does not need to be changed.
Seite 274MOBILITYReplacing
components274
Online Edition for Part no. 01402120596 - II/18

If despite driving with the headlights switched on,
increasing humidity forms, for instance water
droplets in the light, have the headlights
checked.
Headlight
settingThe headlight adjustments can be affected by
changing lights and bulbs. After the headlight adj
justment was changed, have it checked and, if
necessary, corrected by a dealerss service center
or another qualified service center or repair shop.
Front
lights,
bulb
replacement
Halogen
headlights Overview1High beams, headlight flasher2Low beams3Side marker lights4Turn signal5Parking lights / daytime running lights.6Parking lights / daytime running lights.
Parking
lights,
daytime
running
lights
The parking lights and daytime running lights are made using LED technology.
In the case of a malfunction, contact a dealerss
service center or another qualified service center or repair shop.
Accessing
the
turn
signals,
low
beams,high
beams/headlight
flasher
Follow the safety information, refer to page 274.
Open the hood, refer to page 263.
Turn
signal
Bulb A23571.Access to the turn signal on the right side:
unhook and fold away the filler neck for the wiper fluid with the screwdriver from the onj
board vehicle tool kit.2.Turn the bulb socket counterclockwise and remove.3.Press the bulb gently into the socket, turncounterclockwise and remove.4.Install the new bulb and bulb holder in reverse
order of removal.
Low
beams
55 watt bulb, H7LL.
1.Access to the low beams on the right side:
unhook and fold away the filler neck for theSeite 275Replacing
componentsMOBILITY275
Online Edition for Part no. 01402120596 - II/18

wiper fluid with the screwdriver from the onj
board vehicle tool kit.2.Turn the cover counterclockwise and rej move.3.Pull the bulb holder directly to the rear, arj
row 1, and remove.4.Remove the bulb from the bulb holder.5.Install the new bulb with bulb holder in rej verse order of removal.
In doing so, ensure that the bulb tab is corj
rectly positioned in the headlight housing and
the bulb holder perceptibly engages.6.Close the headlight housing with the lid.
Make sure that the lid engages.High
beams/headlight
flasher
55-watt bulb, H7.1.Turn the cover counterclockwise and rej move.2.Pull the bulb holder directly to the rear, arj
row 1, and remove.3.Remove the bulb from the bulb holder.4.Install the new bulb with bulb holder in rej verse order of removal.
In doing so, ensure that the bulb tab is corj
rectly positioned in the headlight housing and
the bulb holder perceptibly engages.5.Close the headlight housing with the lid.
Make sure that the lid engages.Seite 276MOBILITYReplacing
components276
Online Edition for Part no. 01402120596 - II/18

LED
headlights
Overview
Front
lights1Parking lights / daytime running lights2Side marker lights3Turn signal4Low beams, high beams/headlight flasher5Cornering light
Front
lights
The following lights feature LED technology:
'xHigh beams'xParking lights / daytime running lights'xLow beams'xCornering light
In the case of a malfunction, contact a dealerss service center or another qualified service centeror repair shop.
Turn
signal
Bulb A2357
Accessing
the
turn
signals
Follow the safety information, refer to page 274.
Open the hood.
1.Access to the turn signal on the right side:
unhook and fold away the filler neck for thewiper fluid with the screwdriver from the onj
board vehicle tool kit.2.Turn the bulb socket counterclockwise and remove.3.Press the bulb gently into the socket, turncounterclockwise and remove.4.Install the new bulb and bulb holder in reverse
order of removal.
Halogen
front
fog
lights
Follow the safety information, refer to page 274.
Seite 277Replacing
componentsMOBILITY277
Online Edition for Part no. 01402120596 - II/18

35-watt bulb, H8.1.Insert the screwdriver from the onboard vehijcle tool kit, with the flat side on the clip, arjrow 1.2.Turn the screwdriver by 90p, arrow 2.3.Remove the front fog light toward the front.4.Detach the connector.5.Turn the bulb bracket and remove it.6.Remove the bulb and replace it.7.Proceed in reverse order to insert the front
fog light. Note the guide rails in doing so.
Turn
signal
in
exterior
mirror
The turn signals in the exterior mirrors feature
LED technology. In the case of a malfunction,
contact a dealerss service center or another
qualified service center or repair shop.
Tail
lights,
bulb
replacement
Vehicles
with
halogen
headlights1Side marker lights2Turn signal3Reversing light4Inside brake light5Tail lights6Brake lights/tail lights
Vehicles
featuring
LED
headlights
1Turn signal2Reversing light3Inside brake light4Tail lights5Brake light
The tail lights feature LED technology. In the
case of a malfunction, contact a dealerss service center or another qualified service center or rej
pair shop.
Seite 278MOBILITYReplacing
components278
Online Edition for Part no. 01402120596 - II/18

Bulb
replacement,
exterior
tail
lights
General
information
Follow the safety information, refer to page 274.
Turn signal: 21-watt bulb, P21WLL. Outer brake light: 21 watt bulb, P21WLL.
Removing
the
exterior
tail
light1.Open the tailgate.2.Remove the fastening using the screw driver
from the onboard vehicle tool kit, arrow 1.
Remove cover, arrow 2.3.Loosen both nuts, arrow 1, of the outer tail
light. Use the handle of the screwdriver from the onboard vehicle tool kit to loosen.
Carefully pull out the tail light from the body
toward the front, arrow 2. Ensure that the wirj
ing is not damaged.4.Pull the plug out of the bulb holder and have
the tail light wiring hang outside.
Replacing
the
bulbs
1.Loosen the three fasteners, arrow 1, on the bulb holder.Remove the bulb holder from the tail light, arj
row 2.2.Press the nonworking bulb gently into the socket, turn counterclockwise and remove.'xUpper bulb: turn signal.'xLower bulb: brake light.3.Proceed in the reverse order to insert the
new bulb and attach the bulb holder. Make
sure that the bulb holder engages in all fasj
teners.
Installing
the
tail
light
1.Connect the plug and mount the wiring on
the tail light, arrow 1.2.Place the tail light with the tab, arrow 2, on
the anchor of the body and push onto both of the threaded bolt.3.Press on the tail lights until flush and tighten
both of the nuts.4.Mount the cover. Make sure that the plastic
tabs of the cover are correctly seated in the corresponding recesses of the body.Seite 279Replacing
componentsMOBILITY279
Online Edition for Part no. 01402120596 - II/18

Lights
in
the
tailgateVehicles
with
halogen
headlights
Follow the safety information, refer to page 274.
Reversing light: 21-watt bulb, P21WLL
Inner brake light: 21-watt bulb, H21WLL
Tail light: 5-watt bulb, P21WLL
Vehicles
featuring
LED
headlights
Follow the safety information, refer to page 274.
Reversing light: 21-watt bulb, P21WLL
Inner brake light: 21-watt bulb, H21WLL
Accessing
the
lights1.Open the tailgate.2.Pull out the cover at the recessed grip.3.Remove the plug from the bulb holder.
Replacing
reversing
light
and
inner
brake
light
1.Loosen the fasteners, arrow 1, on the bulb
holder.
Remove the bulb holder from the tail light, arj
row 2.2.Press the nonworking bulb gently into the socket, turn counterclockwise and remove.'xUpper bulb: reversing light'xLower bulb: inner brake light
Only vehicles with halogen headlights:
'xLower bulb, 5-watt: tail light
Installing
the
bulb
holder
1.Proceed in the reverse order to insert the
new bulb and attach the bulb holder.
Connect the plug to the bulb holder.2.Make sure that the bulb holder is correctly and firmly seated.
Central
brake
light
and
license
plate
lights
Follow the safety information, refer to page 274.
These lights are made using LED technology. In the case of a malfunction, contact a dealerss
service center or another qualified service center or repair shop.
Vehicle
battery
Maintenance
The battery is maintenance-free.
The added amount of acid is sufficient for the service life of the battery.
More information about the battery can be rej
quested from a dealerss service center or another qualified service center or repair shop.
Replacing
the
vehicle
battery
General
information The manufacturer of your vehicle recommends
that you have a dealerss service center or another qualified service center or repair shop register
the vehicle battery to the vehicle after the battery
has been replaced. Once the battery has been registered again, all comfort features will be availj
Seite 280MOBILITYReplacing
components280
Online Edition for Part no. 01402120596 - II/18