BMW X2 2018 Owners Manual

OverviewDepending
on
the
vehicle
equipment:
button
in
the
vehicle
Park assistance button
Camera
The camera lens is located between the license plate lights.
The image quality may be impaired by dirt. If
necessary, clean the camera lens.
Switching
on/off
Switching
on
automatically The system is switched on automatically if selecj
tor lever position R is engaged when the engine
is running.
Automatic
deactivation
during
forward
travel
The system switches off when a certain driving
distance or speed is exceeded.
Switch the system back on, if needed.
Depending
on
the
vehicle
equipment:
switching
on/off
manually
Press park assistance button.'xOn: the LED lights up.'xOff: the LED goes out.
The parking assistance functions are shown on
the Control Display.
Switching
the
view
via
iDrive If the rearview camera view is not displayed,
change the view via iDrive:
1.Move the Controller to the left, if needed.2. "Rear view camera"
The rearview camera image is displayed.
Display
on
the
Control
Display Functional
requirement
'xThe rearview camera is switched on.'xThe tailgate is fully closed.'xKeep the recording range of the camera
clear. Protruding cargo or carrier systems and
trailers that are not connected to a trailer
power socket can lead to malfunctions.
Activating
assistance
functions
More than one assistance function can be activeat the same time.
Move the Controller to the left, if needed.
'xParking aid lines
"Parking aid lines"
Lanes and turning radius are indicated.
'xObstacle marking
"Obstacle marking"
Obstacles are marked, depending on the vej hicle equipment.
Seite 191Driving
comfortCONTROLS191
Online Edition for Part no. 01402989448 - II/18

Pathway
lines
Pathway lines can be superimposed on the imj
age of the rearview camera.
Pathway lines help you to estimate the space rej
quired when parking and maneuvering on level
roads.
Pathway lines depend on the current steering angle and are continuously adjusted to the steerjing wheel movements.
Turning
radius
lines
Turning radius lines can only be superimposed on the rearview camera image together with
pathway lines.
Turning radius lines show the course of the smallest possible turning radius on a level road.
Only one turning radius line is displayed after the
steering wheel is turned past a certain angle.
Obstacle
marking
Depending on the vehicle equipment, obstacle
markings can be faded into the image of the
rearview camera.
The colored thresholds of the obstacle markings
match the markings of the PDC Park Distance
Control.
Parking
using
pathway
and
turning
radius
lines
1.Position the vehicle so that the turning radius lines lead to within the limits of the parking
space.2.Turn the steering wheel to the point where the pathway line covers the corresponding
turning radius line.Seite 192CONTROLSDriving
comfort192
Online Edition for Part no. 01402989448 - II/18

Display
settingsBrightnessWith the rearview camera switched on:1.Move the Controller to the left, if needed.2. Select the symbol.3.Turn the Controller until the desired setting isreached, and press the Controller.
Contrast
With the rearview camera switched on:
1.Move the Controller to the left, if needed.2. Select the symbol.3.Turn the Controller until the desired setting is reached, and press the Controller.
System
limits
Detection
of
objects Very low obstacles as well as high, protruding
objects such as ledges may not be detected by the system.
Depending on the vehicle equipment, some asj
sistance functions also consider data from the PDC Park Distance Control.
Follow the notes in the PDC Park Distance Conj
trol chapter.
The objects displayed on the Control Display may be closer than they appear. Do not estimate
the distance from the objects on the display.
Parking
assistant
Concept
This system assists the driver in parking parallel
to the road.
General
information
Parking assistant handling is divided into three
steps:
'xSwitching on and activating.'xParking space search.'xParking.
System status and instructions on required acj
tions are displayed on the Control Display.
Ultrasound sensors measure parking spaces on
both sides of the vehicle.
The parking assistant calculates the best possij
ble parking line and takes control of steering durj
ing the parking procedure.
The parking assistant uses the sensors of PDC
Park Distance Control. Also follow the safety inj
formation for PDC Park Distance Control.
Safety
information
WARNING
The system cannot serve as a substitute for the
driverss personal judgment in assessing the
traffic situation. Based on the limits of the sysj
tem, it cannot independently react to all traffic situations. There is a risk of an accident. Adjust
driving style to traffic conditions. Watch traffic
Seite 193Driving
comfortCONTROLS193
Online Edition for Part no. 01402989448 - II/18

closely and actively intervene where approprij
ate.
NOTICE
The parking assistant can steer the vehicle over or onto curbs. There is a risk of damage to property. Watch traffic closely and actively inj
tervene where appropriate.
Also follow the safety information for PDC Park
Distance Control.
Overview Button
in
the
vehicle
Park assistance button
Ultrasound
sensors
The ultrasound sensors for measuring parking
spaces are located on the side of the vehicle.
Functional
requirements
Ultrasound
sensors Ensure full functionality:'xDo not cover sensors, for instance with stickj
ers.'xKeep the sensors clean and unobstructed.
For
measuring
parking
spaces
'xMaximum speed while driving forward approx.
22 mph/35 km/h.'xMaximum distance to row of parked vehicles:
5 ft/1.5 m.
Suitable
parking
space
'xGaps behind an object that has a min. length
of 5 ft/1.5 m.'xGap between two objects with a minimum
length of approx. 5 ft/1.5 m.'xMin. length of gap between two objects: your
vehicle's length plus approx. 3.3 ft/1.0 m.'xMinimum depth: approx. 5 ft/1.5 m.
For
parking
'xDoors and tailgate closed.'xParking brake released.'xWhen parking in parking spaces on the drivj er's side, the corresponding turn signal mustbe switched on.
Switching
on
and
activating
Switching
on
with
the
button Press park assistance button.
The LED lights up.
The current status of the parking space search is
indicated on the Control Display.
Parking assistant is activated automatically.
Seite 194CONTROLSDriving
comfort194
Online Edition for Part no. 01402989448 - II/18

Switching
on
with
reverse
gearShift into reverse.
The current status of the parking space search is indicated on the Control Display.
To activate:
"Parking Assistant"
Display
on
the
Control
Display System
activated/deactivated
SymbolMeaning Gray: the system is not available.
White: the system is available but not
activated. The system is activated.
Parking
space
search
and
system
status
'xSymbol P on the vehicle image: the parking
assistant is activated and the parking space search is active.'xControl Display shows suitable parking
spaces at the edge of the road next to the vej
hicle symbol. When the parking assistant is active, suitable parking spaces are highj
lighted.'xThe parking procedure is acj
tive. Steering control has been
taken over by system.'xParking space search is always active whenj ever the vehicle is moving forward slow andstraight, even if the system is deactivated.
When the system is deactivated, the displays
on the Control Display are shown in gray.
Parking
using
the
parking
assistant
1. Press the park assistance button or
shift into reverse gear to switch on the parkj ing assistant, refer to page 194. Activate the
parking assistant, if needed.
Parking assistant is activated.
2.Pass the row of parked vehicles at a speed of up to approx. 22 mph/35 km/h and at a disj
tance of maximum 5 ft/1.5 m.
The status of the parking space search and
possible parking spaces are displayed, refer to page 195, on the Control Display.3.Follow the instructions on the display.
The best possible parking position will come
after gear change on the stationary vehicle -
wait for the automatic steering wheel move.
The end of the parking procedure is indicated
on the display.4.Adjust the parking position yourself, if
needed.
Interrupting
manually
The parking assistant can be interrupted at any
time:
'x "Parking Assistant" Select the symbol on
the Control Display.'xPress park assistance button.
Interrupting
automatically
The system is interrupted automatically in the
following situations:
'xIf the driver grasps the steering wheel or takes over steering.'xIf a gear is selected that does not match the
instruction on the display.Seite 195Driving
comfortCONTROLS195
Online Edition for Part no. 01402989448 - II/18

'xIf the vehicle speed exceeds approx.
6 mph/10 km/h.'xPossibly on snow-covered or slippery road
surfaces.'xIf a maximum number of parking attempts or
the time taken for parking is exceeded.'xIf the PDC Park Distance Control displays
clearances that are too small.'xWhen switching to another function on the Control Display.
A Check Control message is displayed.
Resuming
An interrupted parking procedure can be continj
ued, if needed.
Reactivate the parking assistant, refer to page 194, and follow the instructions on the disj
play.
Switching
offThe system can be switched off as follows:
'xPress park assistance button.'xSwitching off the ignition.
System
limits
Safety
information
WARNING
The system can react not at all, too late, incorj
rectly, or without justification due to the system
limits. There is a risk of accidents or risk of damage to property. Follow the information rej
garding the system limits and actively intervene
if needed.
No
parking
assistance
The parking assistant does not offer assistance
in the following situations:
'xIn tight curves.Functional
limitations
The system may not be fully functional in the folj
lowing situations:'xOn bumpy road surfaces such as gravel roads.'xOn slippery ground.'xOn steep uphill or downhill grades.'xWith accumulations of leaves/snow in the
parking space.'xWith a mounted emergency wheel.'xWith ditches or edges, for instance an edge
of a port.
Limits
of
ultrasonic
measurement
Ultrasonic measurements might not function in the following situations:
'xFor small children and animals.'xFor persons with certain clothing, for instancecoats.'xWith external interference of the ultrasound,
for instance from passing vehicles or loud
machines.'xWhen sensors are dirty, iced over, damaged
or out of position.'xUnder certain weather conditions such as
high relative humidity, wet conditions, snowj
fall, extreme heat, or strong wind.'xWith tow bars and trailer couplings of other
vehicles.'xWith thin or wedge-shaped objects.'xWith moving objects.'xWith elevated, protruding objects such as ledges or cargo.'xWith objects with corners and sharp edges.'xWith objects with a fine surface structure
such as fences.'xFor objects with porous surfaces.'xIf cargo protrudes.'xLow objects already displayed, for instance
curbs, can move into the blind area of theSeite 196CONTROLSDriving
comfort196
Online Edition for Part no. 01402989448 - II/18

sensors before or after a continuous tonesounds.
Parking spaces that are not suitable may be dej
tected or suitable parking spaces may not be dej tected at all.
Tire
size
The parking position may vary depending on the
tire size.
Malfunction
A Check Control message is displayed. The parking assistant failed. Have the system
checked by a dealerss service center or another
qualified service center or repair shop.
Seite 197Driving
comfortCONTROLS197
Online Edition for Part no. 01402989448 - II/18

Climate
controlVehicle
features
andoptions
This chapter describes all standard, country-spejcific and optional features offered with the series. It also describes features that are not necessarilyavailable in your vehicle, e. g., due to the selectedoptions or country versions. This also applies to
safety-related functions and systems. When usj
ing these functions and systems, the applicable laws and regulations must be observed.
Interior
air
quality
The air quality inside the vehicle is improved by
an emissions-tested interior, a microfilter, and a
climate-control system for regulating temperaj
ture, air flow, and recirculated-air mode.
In addition there are other functions which dej
pend on the vehicle's equipment, for instance
microfilter/activated-charcoal filter, automatic clij
mate control with automatic recirculated-air conj
trol AUC, and parked-car ventilation.Air
conditioner
1Air distribution settings2Air conditioning3Air flow4Air flow display5Recirculated-air mode6Temperature7Seat heating, right\_ 938Rear window defrosterSeite 198CONTROLSClimate
control198
Online Edition for Part no. 01402989448 - II/18

9Seat heating, left\_93Climate
control
functions
in
detail
Switching
the
system
on/off
Switching
on
Press any button except for the following:'xRear window defroster.'xSeat heating.
Switching
off
Press and hold the left button until thecontrol switches off.
Temperature
Concept
The system heats or cools, depending on the set
temperature.
Settings Turn the ring to set the desired
temperature.
Do not rapidly switch between different temperaj
ture settings. Otherwise, the automatic climate control will not have sufficient time to adjust the
set temperature.
Air
conditioning
Concept
The air in the car's interior will be cooled and dej humidified and, depending on the temperaturesetting, warmed again.
The car's interior can only be cooled with the enj
gine running.
Switching
on/off
Press button.
The LED is illuminated with air condij
tioning switched on.
Depending on the weather, the windshield and
side windows may fog up briefly when the enj gine is started.
The air conditioner produces condensation waj
ter, refer to page 227, that will exit from below
the vehicle.
Recirculated-air
mode Concept
You may react to unpleasant odors or pollutants
in the immediate environment by temporarily suspending the supply of outside air. The systemthen recirculates the air flow within the vehicle.
Operation Press button repeatedly to select an opj
erating mode:'xLED off: outside air flows in continuously.'xLED on, recirculated-air mode: the supply of
outside air into the vehicle is permanently
blocked.
To prevent window fogging, recirculated-air
mode switches off automatically after a certain amount of time, depending on the environmental
conditions.
With constant recirculated-air mode, the air qualj ity in the car's interior deteriorates and the fogj
ging of the windows increases.
If the windows fog over, switch off recirculated-
air mode and increase the air flow, if needed.
Seite 199Climate
controlCONTROLS199
Online Edition for Part no. 01402989448 - II/18

Controlling
the
air
flow
manually
Concept
The air flow for climate control can be adjusted
manually.
Operation Press the left or right side of the button:
decrease or increase air flow.
The intensity is indicated by LEDs. The highest level is active when seven LEDs are lit.
The air flow from the air conditioner may be rejduced automatically to save battery power.
Controlling
the
air
distribution
manually
Concept
The air distribution for climate control can be adj
justed manually.
Operation Turn the wheel to select the dej
sired program or the desired inj
termediate setting.'x Windows.'x Upper body region.'x Floor area.'x Windows, upper body region, and floor
area.
Defrosting
windows
and
removing
condensation
Make the following settings to defrost the winj
dows and remove condensation:
'xDirect the air distribution onto the windows.'xIncreasing the air flow.'xIncrease the temperature.'xSwitch on the air conditioning if needed.
Rear
window
defroster
Press button. The LED lights up.
The rear window defroster switches off
automatically after a certain period of time.
For permanent activation, press the button for
longer than 3 seconds. To deactivate, press the
button again.
The rear window defroster can only be activated
continuously at an external temperature below
approx. 23