BMW X2 2018 Manual Online

'xBy pressing the button on the outside of the
tailgate. Pressing again closes the tailgate.'xBy pressing the button on the inside of the
tailgate. Pressing again closes the tailgate.'xBy pressing the button on the remote control.
Pressing again continues the opening moj
tion.'xBy pressing or pulling the button in the storj
age compartment. Pulling again continues
the opening motion.
Closing
From
the
outside
Press the button on tailgate's exterior.
From
the
inside Press button in the storage compartmentof the driver's door and keep it pressed.
The remote control must be located in the car's interior for this function.
An acoustic signal sounds before the tailgate is
closed.
From
inside
the
tailgate
Without Comfort Access:
Press button on the inside of the tailgate.
With Comfort Access:
'xPress button, arrow 1, on the inside of thetailgate.'xPress button, arrow 2.
The vehicle will be locked after closing the tailgate. The driver's door must be closed for
this purpose and the remote control must be outside of the vehicle in the area of the tailjgate.
Interruption
of
the
closing
procedure
The closing procedure is interrupted in the folj
lowing situations:
'xIf the vehicle starts off with a jerky movement.'xBy pressing the button on the outside of the
tailgate. Pressing again re-opens the tailgate.'xBy pressing the button on the inside of the
tailgate. Pressing again re-opens the tailgate.'xBy releasing the button in the storage comj partment of the driver's door. Pulling againand holding continues the closing motion.
Malfunction
Safety
information
WARNING
With manual operation of a blocked tailgate, it
can release itself unexpectedly from the blockj
age. There is a risk of injury or risk of damage
to property. Do not operate the tailgate manj
ually if it is blocked. Have it checked by a dealj
erss service center or another qualified service
center or repair shop.
Seite 810pening
and
closingCONTROLS81
Online Edition for Part no. 01402989448 - II/18

Manual
operation
Operate the unlocked tailgate manually with a
slow and smooth motion.
To close the tailgate fully, press down lightly
only. Closing occurs automatically.
Driver
profile
Concept
In the driver profiles, individual settings for sevj
eral drivers can be stored and called up again
when required.
General
information There are three driver profiles with which perj
sonal vehicle settings can be stored. Every rej mote control has one of these driver profiles asjsigned.
If the vehicle is unlocked using a remote control, the assigned personal driver profile will be actijvated. All settings stored in the driver profile are
automatically applied.
If several drivers use their own remote control, the vehicle will adjust the personal settings durj
ing unlocking. These settings are also restored, if
the vehicle has been used in the meantime by a
person with a different remote control.
Changes to the settings are automatically stored
in the driver profile currently activated.
If another driver profile is selected via iDrive, the settings stored in it will be applied automatically.
The new driver profile is assigned to the remote
control currently used.
There is an additional guest profile available that
is not assigned to any remote control. It can be
used to apply settings in the vehicle without
changing the personal driver profiles.
Functional
requirementsFor the system to be able to identify the driver
profile associated to a particular driver, the dej
tected remote control must be clearly allocated
to the driver.
This is the case when:'xThe driver is only carrying his or her own rej
mote control.'xThe driver unlocks the vehicle.'xThe driver gets into the vehicle through the
driver's door.
Settings
The settings for the following systems and funcj
tions are stored in the active profile. The scope of storable settings depends on country and
equipment.
'xUnlocking and locking.'xLights.'xClimate control.'xRadio.'xInstrument cluster.'xProgrammable memory buttons.'xVolumes, tone.'xControl Display.'xNavigation.'xPDC Park Distance Control.'xRearview camera.'xHead-up Display.'xDriving Dynamics Control.'xSeat position, exterior mirror position, steerj
ing wheel position where applicable.
Both the positions saved via the seat memory and the last position set are saved.'xIntelligent Safety.
Profile
management
Selecting
a
driver
profile
Regardless of the remote control in use, a differj
ent driver profile may be activated. This allows
you to call up personal vehicle settings, even if
Seite 82CONTROLS0pening
and
closing82
Online Edition for Part no. 01402989448 - II/18

you did not unlock the vehicle with your own rej
mote control.
Via iDrive:1."My Vehicle"2."Driver profiles"3.Select driver profile.4."OK"'xAll settings stored in the called-up driver proj file are automatically applied.'xThe called-up driver profile is assigned to the
remote control being used at the time.'xIf the driver profile is already assigned to a difj ferent remote control, this driver profile willapply to both remote controls.
Using
a
guest
profile
The guest profile is for individual settings that are
stored in none of the three personal driver proj
files.
Via iDrive:
1."My Vehicle"2."Driver profiles"3."Drive off (guest)"4."OK"
The guest profile cannot be renamed. It is not assigned to the current remote control.
Renaming
a
driver
profile
A personal name can be assigned to the active
driver profile to avoid confusion between the
driver profiles.
Via iDrive:
1."My Vehicle"2."Driver profiles"3.Select driver profile.
The driver profile marked with this symbol
can be renamed.
4."Change driver profile name"5.Enter profile name.6. Select the symbol.
Resetting
a
driver
profile
The settings of the driver profile currently in use
are reset to their factory settings.
Via iDrive:
1."My Vehicle"2."Driver profiles"3.Select driver profile.
The driver profile marked with this symbol
can be reset.
4."Reset driver profile"5."OK"
Exporting
driver
profiles
Most settings of the active driver profile can be
exported.
Exporting is helpful when storing and retrieving personal settings, for instance before delivering the vehicle to a workshop. The stored driver projfiles can be taken into another vehicle.
Via iDrive:
1."My Vehicle"2."Driver profiles"3.Select driver profile.
The driver profile marked with this symbol
can be exported.
4."Export driver profile"5.Select a storage device for exporting the driver profile.'x"USB device"
Select USB storage device, as needed, refer to page 59.'xOnline.
Importing
driver
profiles
The existing settings of the active driver profileare overwritten with the settings of the importeddriver profile.
Seite 830pening
and
closingCONTROLS83
Online Edition for Part no. 01402989448 - II/18

Via iDrive:1."My Vehicle"2."Driver profiles"3.Select the driver profile to be overwritten.
The driver profile marked with this symbol
can be overwritten.
4."Import driver profile"5.Select a storage device for importing the
driver profile.'xUSB storage device: "USB device"
Select USB storage device as needed.'xOnline.6.Select the driver profile to be imported.
Displaying
driver
profiles
during
start
The driver profiles can be displayed during each
start to select the desired profile.
Via iDrive:
1."My Vehicle"2."Driver profiles"3."Show driver profiles at startup"
System
limits
A clear assignment between the remote controland driver may not be possible in the following
cases, for example.
'xThe passenger unlocks the vehicle with his or
her own remote control, but another person is driving.'xThe driver unlocks the vehicle via Comfort
Access and has multiple remote controls with him or her.'xThe driver changes, but the vehicle is not
locked and unlocked.'xMultiple remote controls are located outside
of the vehicle.Settings
General
information
Depending on the vehicle equipment and counj
try version, various settings for opening and closj ing are possible.
These settings are stored for the driver profile,
refer to page 82, currently used.
Unlocking Doors
Via iDrive:
1."My Vehicle"2."Vehicle settings"3."Doors/Key"4. "Driver's door" or "All doors"5.Select desired setting:'x"Driver's door only"
Only the driver's door and the fuel filler flap are unlocked. Pressing again unlocks
the entire vehicle.'x"All doors"
The entire vehicle is unlocked.
Tailgate
Depending on the vehicle equipment and counj
try version, this setting may not be offered.
Via iDrive:
1."My Vehicle"2."Vehicle settings"3."Doors/Key"4.
The text next to the symbol indicates the curj
rent setting.5.Select desired setting:'x"Tailgate"Seite 84CONTROLS0pening
and
closing84
Online Edition for Part no. 01402989448 - II/18

Depending on your vehicle's optional feaj
tures, the tailgate is either unlocked or opened.'x"Tailgate and door(s)"
Depending on your vehicle's optional feaj
tures, the tailgate is either unlocked or
opened and the doors unlocked.'x"Tailgate opens after unlocking"
The vehicle must be unlocked before the
tailgate can be used with the remote conj trol.'x"Button lock"
It is not possible to use the tailgate via the
remote control.
Adjusting
the
last
seat
and
mirror
position
Via iDrive:
1."My Vehicle"2."Driver profiles"3.Select driver profile.
The setting can be made for the driver
profile marked with this symbol.
4."Last seat position automatic"
When the vehicle is unlocked, the driver's seat and exterior mirrors resume their last set posij
tions.
The most recent position is independent of the positions saved via the seat memory.
Confirmation
signals
from
the
vehicle
Via iDrive:
1."My Vehicle"2."Vehicle settings"3."Doors/Key"4.Deactivate or activate the desired confirmajtion signals.'x"Flash for lock/unlock"Unlocking is signaled by two flashes, lockj
ing by one.'xWith alarm system:
"Acoustic signal for lock/unlock"
Unlocking is signaled by one honk of the
horn.
Automatic
locking
Via iDrive:
1."My Vehicle"2."Vehicle settings"3."Doors/Key"4.Select desired setting:'x"Lock automatically"
The vehicle locks automatically after a
short period of time if no door is opened
after unlocking.'x"Lock after starting to drive"
The vehicle locks automatically after you
drive off.
Automatic
unlocking
Via iDrive:
1."My Vehicle"2."Vehicle settings"3."Doors/Key"4."Unlock at end of trip"
After the engine is switched off by pressing the Start/Stop button, the locked vehicle is
automatically unlocked.
Alarm
system
General
information
When the vehicle is locked, the vehicle alarm
system reacts to the following changes:
'xUnauthorized opening of a door, the hood or
the tailgate.Seite 850pening
and
closingCONTROLS85
Online Edition for Part no. 01402989448 - II/18

'xMovements in the car's interior.'xChanges in the vehicle tilt, e. g., during atj
tempts at stealing a wheel or when towing
the vehicle.'xDisconnected battery voltage.'xImproper use of the socket for Onboard Diagj nosis.
The alarm system signals these changes visuallyand acoustically:
'xAcoustic alarm:
Depending on local regulations, the acoustic alarm may be suppressed.'xVisual alarm:
By flashing the exterior lighting.
Switching
on/off
When you lock and unlock the vehicle with the
remote control or Comfort Access, the alarm
system will also switch on or off at the same time.
Opening
the
doors
with
the
alarm
system
switched
on
The alarm system is triggered when a door is opened if the door was unlocked using the
integrated key in the door lock.
Switching off the alarm, refer to page 87.
Opening
the
tailgate
with
the
alarm
system
switched
on
The tailgate can be opened even when the alarm
system is switched on.
After the tailgate is closed, it is locked and monij
tored again provided the doors are locked. The
hazard warning system flashes once.
Panic
mode
You can trigger the alarm system if you find yourj self in a dangerous situation.
'xPress button on the remote control
and hold for at least 3 seconds.'xBriefly press the button on the remote control three times in succession.
To switch off the alarm: press any button.
Indicator
light
on
the
interior
mirror
'xThe indicator light flashes briefly every 2 secj onds:
The alarm system is switched on.'xIndicator light flashes for approx. 10 seconds,
then it flashes briefly every 2 seconds:
Interior motion sensor and tilt alarm sensor
are not active, as doors, hood, or tailgate are not correctly closed. Correctly closed access
points are secured.
When the still open access points are closed,
interior motion sensor and tilt alarm sensor will be switched on.'xThe indicator light goes out after unlocking:
The vehicle has not been tampered with.'xThe indicator light flashes after unlocking unj til the engine ignition is switched on, but no
longer than approx. 5 minutes:
An alarm has been triggered.
Tilt
alarm
sensor
The tilt of the vehicle is monitored.
The alarm system responds in situations such as
attempts to steal a wheel or when the vehicle is
towed.
Seite 86CONTROLS0pening
and
closing86
Online Edition for Part no. 01402989448 - II/18

Interior
motion
sensor
The windows and the glass sunroof must be
closed for the system to function properly.
Avoiding
unintentional
alarms General
information The tilt alarm sensor and interior motion sensor
can trigger an alarm, although no unauthorized
action occurred.
Possible situations for an unwanted alarm:'xIn automatic vehicle washes.'xIn duplex garages.'xDuring transport on trains carrying vehicles, at
sea or on a trailer.'xWith animals in the vehicle.'xAt the gas station: if the vehicle is locked after refueling starts.
The tilt alarm sensor and the interior motion senj
sor can be switched off in such situations.
Switching
off
the
tilt
alarm
sensor
and
interior
motion
sensor
Press the remote control button againwithin 10 seconds as soon as the vehicle is
locked.
The indicator light lights up for approx. 2 secj
onds and then continues to flash.
The tilt alarm sensor and interior motion sensor are switched off until the vehicle is locked again.
Switching
off
the
alarm
'xUnlock the vehicle with the remote control or switch on the ignition, if needed throughemergency detection of remote control, refer
to page 73.'xWith Comfort Access:
If you are carrying the remote control on your
person, grasp the door handle on the driver's
or front passenger door completely.Power
windows
General
information
If an accident of a certain severity occurs, the
windows are automatically closed except a gap.
Safety
information
WARNING
When operating the windows, body parts and objects can be jammed. There is a risk of injury or risk of damage to property. Make sure thatthe area of movement of the windows is clear
during opening and closing.
Overview
Power windows
Safety switch
Opening
'x Press the switch to the resistance point.
The window opens while the switch is being held.'x Press the switch beyond the resistance
point.
The window opens automatically. Pressing
the switch again stops the motion.
Seite 870pening
and
closingCONTROLS87
Online Edition for Part no. 01402989448 - II/18

Convenient opening via the remote control, referto page 71.
Closing'x Pull the switch to the resistance point.
The window closes while the switch is being
held.'x Pull the switch beyond the resistance
point.
The window closes automatically if the door
is closed. Pulling again stops the motion.
Closing via Comfort Access, refer to page 76.
Jam
protection
system
General
information
If closing force exceeds a specific threshold as a
window closes, closing is interrupted.
The window opens slightly.
Safety
information
WARNING
Accessories on the windows such as antennas can impact jam protection. There is a risk of inj jury. Do not install accessories in the area of
movement of the windows.
Closing
without
the
jam
protection
system
In case of danger from the outside or if ice might
prevent normal closing, proceed as follows:
1. Pull the switch past the resistance point
and hold it there.
The window closes with limited jam protecj
tion. If the closing force exceeds a specific threshold, closing is interrupted.2. Pull the switch past the resistance point
again within approx. 4 seconds and hold it
there.
The window closes without jam protection.
Safety
switch
General
information The safety switch in the driver's door can beused to prevent children, for instance from openjing and closing the rear windows using the
switches in the rear.
If an accident of a certain severity occurs, the
safety function is switched off automatically.
Switching
on/off Press button.
The LED lights up if the safety function
is switched on.
Panoramic
glass
sunroof
General
informationThe glass sunroof is ready for operation when
the ignition is switched on.
In the event of a severe accident, the glass sunj
roof is automatically closed.
Safety
information
WARNING
Body parts can be jammed when operating the
glass sunroof. There is a risk of injury. Make
sure that the area of movement of the glass
sunroof is clear during opening and closing.
Seite 88CONTROLS0pening
and
closing88
Online Edition for Part no. 01402989448 - II/18

Overview
Tilting
up
and
closing
the
tilted
glass
sunroof
Push switch briefly upward.
'xThe closed glass sunroof tilts
and the sun protection opens
slightly.'xThe opened glass sunroof
closes until it is in the tilted
position. The sun protection
does not move.'xThe tilted glass sunroof closes.
Opening/closing
the
glass
sunroof
and
sun
protection
separately
'xPress the switch in the desired
direction to the resistance
point and hold it there.
Holding down the switch
opens the sun protection. If
the sun protection is already
fully open, the glass sunroof
opens.
The glass sunroof closes
while the switch is being held.
If the glass sunroof is already
closed or in the tilted position,
the sun protection closes.'xPress the switch in the desired direction past the resistance point.The sun protection opens automatically. If thesun protection is already fully open, the glass
sunroof opens automatically.
The glass sunroof closes automatically. If the
glass sunroof is already closed or in the tilted
position, the sun protection closes automatij
cally.
Pressing the switch upward stops the motion.
Opening/closing
the
glass
sunroof
and
sun
protection
together
Briefly press the switch twice insuccession in the desired direcjtion past the resistance point.
The glass sunroof and sun proj
tection move together. Pressing
the switch upward stops the motion.
Convenient opening via the remote control, refer
to page 71.
Closing via Comfort Access, refer to page 75.
Comfort
position
In some models, the wind noises in the car's inj
terior are lowest when the glass sunroof is not
fully open. In these models, the automatic funcj
tion initially only opens the glass sunroof up to
this comfort position.
Pressing the switch again opens the glass sunj
roof fully.
Jam
protection
system
General
information
If the closing force exceeds a certain value when closing the glass sunroof, the closing operation isinterrupted once the roof reaches the half-openposition, or it is stopped when closing from the
tilted position. The glass sunroof opens slightly.
Seite 890pening
and
closingCONTROLS89
Online Edition for Part no. 01402989448 - II/18

Closing
from
the
open
position
without
jam
protection
If there is an external danger, proceed as follows:1.Push the switch forward past the resistancepoint and hold.
The glass sunroof closes with limited jam
protection. If the closing force exceeds a spej
cific threshold, closing is interrupted.2.Push the switch forward again past the resistj
ance point and hold until the glass sunroof closes without jam protection. Make sure that
the closing area is clear.
Closing
from
the
raised
position
without
jam
protection
If there is an external danger,push the switch forward past the
resistance point and hold it.
The glass sunroof closes without jam protection.
Initializing
after
a
power
interruption
General
information
After a power failure during the opening or closj
ing process, the glass sunroof can only be operj
ated to a limited extent.
The system can be initialized under the following
conditions.
'xThe vehicle is parked in a horizontal position.'xThe engine is running.'xThe external temperature is above
41