AUX BMW X5 2004 E53 M62TU Engine Workshop Manual

TABLE OF CONTENTS
SubjectPage
M62TU Engine . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 2
Vanos Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-12
Engine Cooling System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
IHKA System Auxilary Pump. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
DME-ME 7.2 Engine Management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
IPO ME 7.2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Integral Electronic Throttle System (EML). . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Input Signal/Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Camshaft Position Sensors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Hot Film Air Mass Sensor (HFM 5). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Integrated Ambient Barometeric Pressure Sensor. . . . . . . . . . . . . . . . . . .21
Radiator Outlet Temperature Sensor. . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
DSC III Road Speed Signal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Accelerator Pedal Sensor (PWG). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
EDK Throttle Position Feedback Signal. . . . . . . . . . . . . . . . . . . . . . . . . . 24
MFL Cruise Control Data Signal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Brake Light Switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Can Bus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Output Control Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . .27
E-Box. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Secondary Air Injection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Auxiliary Fan Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Electric Throttle Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
DM-TL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . 31
Leak Diagnosis Test Precondition. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

2
M62TU Engine / ME7.2
The 4.4i X5 is equipped with the M62 TU B44 (4.4 liter) engine. Features of the M62 TU
engine include:
• Digital motor Electronics Control ME 7.2.
• Variable positioned intake camshaft VANOS system.
• “EML” Electronic Throttle Control System identified as EDK.
• Compact water cooled generator (F-alternator).
• Thermostat controlled transmission fluid/engine coolant heat exchanger system for
automatic transmission equipped vehicles.
• Non Return Fuel Rail (Running Loss Compliance).
• IHKA Auxillary Water Pump.

14
IHKA SYSTEM AUXILIARY PUMP
The auxiliary water pump for the IHKA is mounted on the left side of the radiator. The func-
tion of the pump remains the same as follows:
• provide adequate coolant flow for IHKA opera-
tion.
• provide coolant circulation for the REST function
of IHKA.

15
DME-ME 7.2 ENGINE MANAGEMENT SYSTEM
The “ME” designation identifies the system as “M” = Motronic, “E” = EML.
• Manufactured by Bosch to BMW specifica-
tions
• 134 pin SKE (standard shell construction) con-
trol module located in E box
• Diagnostic communication protocol-KWP2000
• Uses break-out box set (P/N 90 88 6 121 300)
• Integral EML throttle control system
- monitors an interior installed PWG
- actuates an electric throttle valve (EDK)
• Integral Cruise control functionality
- monitors cruise control requests
- monitors brake pedal and clutch switches
- carries out throttle control directly via EDK
• Carries out DSC III torque reduction requests.
• VANOS control
• Integrated altitude sensor
• Integrated temp sensor for monitoring E box
temperatures
• Control of E-box fan
• One touch engine start control
• Oxygen Sensor heating
• Engine overrev & Max speed limitation
• Active Hall sensor for camshaft position monitoring
• Single speed secondary air injection system
• Electrically heated coolant system thermostat
• Longlife spark plugs
• IHKA Auxiliary Fan control
•DM-TL (Diagnostic Module - Tank Leak Diagnosis System)
ME 7.2 LOCATION IN E-BOX
1
(9 pins)2
(24 pins)3
(52 pins)4
(40 pins)5
(9 pins)

22
RADIATOR OUTLET TEMP SENSOR
First seen on the MS 42.0 control system, the ME
7.2 uses an additional water temperature sensor
located on the radiator outlet.
ME 7.2 requires this signal to monitor the water
temperature leaving the radiator for precise acti-
vation of the IHKA auxiliary fan.
DSC III - ROAD SPEED SIGNAL
ME 7.2 receives the road speed signal directly
from the DSC III control module for maximum
vehicle speed management. The DSC control
module provides a processed output of the right
rear wheel speed sensor as a digital square wave
signal. The frequency of the signal is proportion-
al to the speed of the vehicle (48 pulses per one
revolution of the wheel).
The cruise control function (FGR) of the ME 7.2 also monitors vehicle speed from the redun-
dant vehicle speed CAN bus signal. The CAN bus speed signal is provided by the DSC III
control module and based on the combined average of both front wheel speed signals.
Additionally, ME 7.2 monitors all four wheel speed signals via CAN bus signalling to detect
abrupt fluctuations in vehicle speed signals for the purpose of detecting rough road sur-
faces. This is continuously monitored as part of the OBD II emission requirements provid-
ing a correction factor for misfire detection plausibility. Earlier systems only monitored the
right rear speed signal input from DSC.

29
AUXILIARY FAN CONTROL
The Auxiliary Fan motor incorporates an out-
put final stage that activates the fan motor at
variable speeds.
The auxiliary fan is controlled by ME 7.2. The
motor output stage receives power and
ground and activates the motor based on a
PWM signal (10 - 100 Hz) received from the
ME 7.2.
Similar to the aux fan in the E46 with MS 42.0
control, the fan is activated based on the fol-
lowing factors:
• Radiator outlet temperature sensor input exceeds a preset temperature.
• IHKA signalling via the K and CAN bus based on calculated refrigerant pressures.
• Vehicle speed
• Battery voltage level
When the over temperature light in the instrument cluster is on (120
OC) the fan is run in the
overrun function. This signal is provided to the DME via the CAN bus. When this occurs
the fan is run at a frequency of 10 Hz.
FAN MOTOR MODULE
POWER, GROUND & SIGNAL WIRES