BMW X5M 2018 Owners Manual

container onto the tire valve of the nonj
working wheel.6.With the compressor switched off, insert
the plug into the power socket inside the
vehicle.7.With the ignition switched on or the engine running, switch on the compressor.
Let the compressor run for max. 10 minutes tofill the tire with sealant and achieve a tire inflaj
tion pressure of approx. 2.5 bar.
While the tire is being filled with sealant, the
tire inflation pressure may sporadically reach
approx. 5 bar. Do not switch off the compresj
sor at this point.
If a tire inflation pressure of 2 bar is not
reached:1.Switch off the compressor.2.Pull the connector out of the power socket inside the vehicle.3.Unscrew the filling hose from the tire valve.4.Drive 33 ft/10 m forward and back to disjtribute the sealant in the tire.5.Inflate the tire again using the compressor.
If a tire inflation pressure of 2 bar cannot be
reached, contact your dealerss service cenj
ter or another qualified service center or repair shop.
Stowing
the
Mobility
System
1.Unscrew the filling hose of the sealant conj
tainer from the tire valve.2.Pull the compressor connector out of the socket inside the vehicle.3.Unscrew the connection hose of the comjpressor from the sealant container.4.Connect the filling hose of the sealant conj
tainer previously connected to the tire
valve with the available connector on the
sealant container.
This prevents leftover sealant escaping from the sealant container.5.Wrap and store the sealant container insuitable material to avoid dirtying the cargo
area.6.Stow the Mobility System back in the cargo area.
Distributing
the
sealant
Immediately drive approx. 5 miles/10 km to enjsure that the sealant is evenly distributed in thetire.
Do not exceed the permissible maximum
speed of 50 mph/80 km/h.
If possible, do not drive at speeds less than
12 mph/20 km/h.
Seite 231Wheels
and
tiresMobility231
Online Edition for Part no. 01402985049 - X/17

Correcting
the
tire
inflation
pressure1.Stop at a suitable location.2.Screw the connection hose of the comjpressor directly onto the tire valve stem.3.Insert the connector into the power socket
inside the vehicle.4.Correct the tire inflation pressure to
2.5 bar.'yIncrease tire inflation pressure: with the
ignition switched on or the engine runj
ning, switch on the compressor.'yReduce tire inflation pressure: press
the button on the compressor.
Continuing
the
trip
Do not exceed the maximum permissible
speed of 50 mph/80 km/h.
Reinitialize the run-flat tires.
Reset the Tire Pressure Monitor TPM.
Replace the nonworking tire and the sealant
container of the Mobility System at the next
opportunity.
Snow
chains Safety
information WARNING
With the mounting of snow chains on unj
suitable tires, the snow chains can come into
contact with vehicle parts. There is a risk of acj
cidents or risk of damage to property. Only
mount snow chains on tires that are desigj
nated by their manufacturer as suitable for the
use of snow chains.'

center or another qualified service center or rejpair shop.
Safety
information DANGER
The vehicle jack is only provided for
short-term lifting of the vehicle for wheel changes. Even if all safety measures are objserved, there is a risk of the raised vehicle falljing, if the vehicle jack tilts over. There is a riskof injuries or danger to life. If the vehicle is
raised, do not lie under the vehicle and do not
start the engine.'

On
a
slight
downhill
gradient
If you need to change a wheel on a slightdownhill grade, place chocks and other suitajble objects, for instance a rock, under the
wheels of both the front and rear axles against
the rolling direction.
Lug
bolt
lock
Concept
The wheel lug bolts have a special coding. The
lug bolts can only be released with the adapter
which matches the coding.
Overview
The adapter of the lug bolt lock is in the onj board vehicle tool kit or in a storage compartj
ment close to the onboard vehicle tool kit.
'yLug bolt, arrow 1.'yAdapter, arrow 2.
Unscrewing
1.Attach the adapter to the lug bolt.2.Unscrew the lug bolt.3.Remove the adapter after unscrewing the lug bolt.
Screwing
on
1.Attach the adapter to the lug bolt. If necesj
sary, turn the adapter until it fits on the lug bolt.2.Screw on the lug bolt. The tightening torj
que is 140 Nm.3.Remove the adapter and stow it after screwing on the lug bolt.
Preparing
the
vehicle
'yPark the vehicle on solid and non-slipground at a safe distance from traffic.'ySwitch on the hazard warning system.'ySet the parking brake.'yEngage a gear or move the selector leverto position P.'yAs soon as permitted by the traffic flow,have all vehicle occupants get out of the
vehicle and ensure that they remain outj side the immediate area in a safe place,
such as behind a guardrail.'yDepending on the equipment version, get tools and the emergency wheel from the
vehicle.'yIf necessary, set up a warning triangle or
portable hazard warning light at an approj priate distance.'ySecure the vehicle additionally against rollj
ing.'yLoosen the lug bolts a half turn.Seite 234MobilityWheels
and
tires234
Online Edition for Part no. 01402985049 - X/17

Jacking
points
for
the
vehicle
jack
The jacking points for the vehicle jack are lojcated at the indicated positions.
Jacking
up
the
vehicle WARNING
Hands and fingers can be jammed when
using the vehicle jack. There is a risk of injury. Comply with the described hand position and
do not change this position while using the vej
hicle jack.'

5.Make sure that the vehicle jack foot stands
vertically and at a right angle beneath the jacking point.6.Make sure that the vehicle jack foot stands
vertically and perpendicularly beneath the jacking point after extending the vehicle
jack.7.Crank up the vehicle jack until the entire
surface of the jack is in contact with the
ground and the wheel in question is raised
a maximum of 1.2 inches/3 cm off the ground.
Mounting
a
wheel
Mount one emergency wheel only, as required.
1.Unscrew the lug bolts.2.Remove the wheel.3.Put the new wheel or emergency wheel on and screw in at least two lug bolts in a
crosswise pattern until hand-tight.
If non-original light-alloy wheels of the vej hicle manufacturer are mounted, the acj
companying lug bolts may have to be used
as well.4.Hand-tighten the remaining lug bolts and tighten all lug bolts well in a crosswise patj
tern.5.Turn the vehicle jack crank counterclockj
wise to retract the vehicle jack and lower
the vehicle.6.Remove the vehicle jack and stow it sej
curely.
After
the
wheel
change
1.Tighten the lug bolts crosswise. The tightj ening torque is 101 lb ft/140 Nm.2.Stow the nonworking wheel in the cargo
area, if necessary.
The nonworking wheel cannot be stored under the cargo floor panel because of its
size.3.Check tire inflation pressure at the next opj
portunity and correct as needed.4.Reinitialize the run-flat tires.
Reset the Tire Pressure Monitor TPM.5.Check to make sure the lug bolts are tight
with a calibrated torque wrench.6.Have the damaged tire replaced at the
nearest dealerss service center or another
qualified service center or repair shop.
Emergency
wheel
Concept
In the event of a flat tire, the emergency wheel
can be used in place of the wheel with the dej
fective tire. The emergency wheel is only inj tended for temporary use until the defective
tire/wheel has been replaced.
General
information
Mount one emergency wheel only.
Also check the tire inflation pressure of the
emergency wheel in the cargo area regularly,
and correct it as needed.
Seite 236MobilityWheels
and
tires236
Online Edition for Part no. 01402985049 - X/17

Safety
informationWARNING
The emergency wheel has particular dij
mensions. When driving with an emergency wheel, changed driving properties may occur,
for instance reduced lane stability when brakj
ing, longer braking distance, and changed self-
steering properties in the limit area. There is a
risk of an accident. Drive moderately and do
not exceed a speed of 50 mph/80 km/h.'

Engine
compartmentVehicle
features
and
optionsThis chapter describes all standard, country-specific and optional features offered with theseries. It also describes features that are notnecessarily available in your vehicle, e. g., dueto the selected options or country versions.
This also applies to safety-related functions
and systems. When using these functions and systems, the applicable laws and regulations
must be observed.
Important
features
in
the
engine
compartment
1Filler neck for washer fluid2Vehicle identification number3Coolant reservoir, charge air4Jump-starting, positive battery terminal5Coolant reservoir, engine6Jump-starting, negative battery terminal7Oil filler neckHood
Safety
information WARNING
Improperly executed work in the engine
compartment can damage vehicle compoj nents and impair vehicle functions. There is arisk of personal and property damage. Themanufacturer of your vehicle recommendsthat, in the effort to avoid such risks, work inthe engine compartment be performed by adealerss service center or another qualified
service center or repair shop.'

WARNING
The engine compartment accommoj
dates moving components. Certain compoj nents in the engine compartment can also
move with the vehicle switched off, for inj
stance the radiator fan. There is a risk of injury. Do not reach into the area of moving parts.
Keep articles of clothing and hair away from
moving parts.'

Closing
the
hood
Let the hood drop from a height of approx.
16 inches/40 cm and push down on it to lock it
fully.
The hood must engage on both sides.
Seite 240MobilityEngine
compartment240
Online Edition for Part no. 01402985049 - X/17