BMW X6 2018 Owners Manual

Page 151 of 282

Comfort functions and the engine Controller
are adjusted.
The program can be configured to individual
specifications.
ActivatingECOPRO Press button repeatedly until ECO
PRO is displayed in the instrument
cluster.
ConfiguringECOPRO1.Activate ECO PRO.2. "Configure ECO PRO"
Make the desired settings.
Displaysintheinstrumentcluster
Selectedprogram The instrument cluster displays
the selected program.
Programselection Pressing the button displays a
list of the selectable programs.
Depending on your vehicle's opj tional features, the list in the inj
strument cluster can differ from
the illustration shown.
DisplayontheControlDisplayProgram changes can be displayed briefly on
the Control Display.
To do so, make the following settings:
1."Settings"2."Driving mode"3."Driving mode info"Seite 151DrivingstabilitycontrolsystemsControls151
Online Edition for Part no. 01402981185 - VI/17

Page 152 of 282

DrivingcomfortVehiclefeaturesandoptions
This chapter describes all standard, country- specific and optional features offered with theseries. It also describes features that are notnecessarily available in your vehicle, e. g., due
to the selected options or country versions.
This also applies to safety-related functions
and systems. When using these functions and systems, the applicable laws and regulations
must be observed.
ActiveCruiseControlwith
Stop&GofunctionACC
Concept
Using this system, a desired speed and a disj
tance to a vehicle ahead can be adjusted using
the buttons on the steering wheel.
The system maintains the desired speed on clear roads. For this purpose, the vehicle acj
celerates or brakes automatically.
If a vehicle is driving ahead of you, the system
adjusts the speed of your vehicle so that the
set distance to the vehicle ahead is mainj
tained. The speed is adjusted as far as the
given situation allows.
The distance can be adjusted in several steps.
For safety reasons, it depends on the respecj tive speed.
If the vehicle ahead of you brakes to a halt, and
then proceeds to drive again within a brief pej
riod, the system is able to detect this within the given system limits.
Generalinformation Depending on the driving settings, the featuresof the cruise control can change in certain
areas.Safetyinformation
WARNING
The system does not relieve from perj
sonal responsibility to assess the traffic situaj tion. Based on the limits of the system, it canjnot independently react to all traffic situations.
There is a risk of an accident. Adjust driving style to traffic conditions. Watch traffic closelyand actively intervene where appropriate.'

Page 153 of 282

There is a risk of injuries or danger to life.Watch traffic closely and actively intervenewhere appropriate.'

Page 154 of 282

Press button on the steering wheel.'yIf active: press twice.'yIf interrupted: press once.
The displays go out. The stored desired speed
is deleted.
Interruptingmanually Press button on the steering wheel.
If interrupting the system while stationary,
press on the brake pedal at the same time.
Interruptingautomatically
The system is automatically interrupted in the following situations:
'yWhen the driver applies the brakes.'yWhen selector lever position D is disenj
gaged.'yDynamic Traction Control DTC is activated
or DSC Dynamic Stability Control is deactij vated.'yIf DSC Dynamic Stability Control interj
venes.'yWhen SPORT+ is activated with Driving
Dynamics Control.'yIf the safety belt is unbuckled and the drivj
er's door is opened while the vehicle is standing still.'yIf the system has not detected objects for
an extended period, for instance on a road
with very little traffic without curb or
shoulder markings.'yIf the detection range of the radar is imj paired, for instance by dirt or heavy fog.'yAfter a stationary period of approx. 3 secj
onds when the vehicle has been braked to
a stop by the system.Settingthespeed
Maintaining/storingthespeed
Press the rocker switch while the system is inj terrupted.
When the system is switched on, the current
speed is maintained and stored as the desired
speed.
The stored speed is displayed in the speedomj
eter and briefly in the instrument cluster, refer
to page 155.
DSC Dynamic Stability Control is switched on,
if necessary.
The speed can also be stored bypressing a button.
Press button.
Changingthespeed
Press the rocker switch up or down repeatedly
until the desired speed is set.
If active, the displayed speed is stored and the vehicle reaches the stored speed when the
road is clear.
Seite 154ControlsDrivingcomfort154
Online Edition for Part no. 01402981185 - VI/17

Page 155 of 282

'yEach time the rocker switch is pressed to
the point of resistance, the desired speed increases or decreases by approx.
1 mph/1 km/h.'yEach time the rocker switch is pressed
past the resistance point, the desired
speed changes by a maximum of 5 mph/
10 km/h.
Hold the rocker switch in position to repeat the action.
Adjustingdistance
Safetyinformation WARNING
The system does not relieve from perj
sonal responsibility. Due to the system limits, braking can be late. There is a risk of accidentsor risk of damage to property. Be aware to thetraffic situation at all times. Adjust the distance
to the traffic and weather conditions and mainj
tain the prescribed safety distance, possibly by braking.'

Page 156 of 282

Distance displayDistance 1Distance 2Distance 3Distance 4
This value is set automatically after
the system is switched on.The system has been interrupted or
distance control is temporarily supj
pressed because the accelerator
pedal is being pressed; a vehicle
was not detected.Distance control is temporarily supj
pressed because the accelerator
pedal is being pressed; a vehicle
was detected.
Detectedvehicle
Symbol lights up orange:
A vehicle has been detected ahead of
you.
Rolling bars: the detected vehicle has driven
away.
ACC does not accelerate. To accelerate, actij
vate ACC by briefly stepping on the acceleraj
tor pedal or pressing the RES button or the rocker switch.
Indicator/warninglights Symbol flashes orange:
The conditions are not adequate for
the system to work.
The system was deactivated but applies the brakes until you actively resume control by
pressing on the brake pedal or accelerator
pedal.
Symbol flashes red and a signal
sounds:
Brake and make an evasive maneuver,
if necessary.
DisplaysintheHead-upDisplay Some system information can also be disjplayed in the Head-up Display.
Distanceinformation The symbol is displayed when the disj
tance from the vehicle traveling ahead
is too short.
The distance information is active under the
following circumstances:'yActive Cruise Control switched off.'yDisplay in the Head-up Display selected, refer to page 104.'yDistance too short.'ySpeed greater than approx.
40 mph/70 km/h.
Systemlimits
Detectionrange
The detection capacity of the system and the
automatic braking capacity are limited.
Two-wheeled vehicles for instance might not
be detected.
Seite 156ControlsDrivingcomfort156
Online Edition for Part no. 01402981185 - VI/17

Page 157 of 282

Deceleration
The system also does not decelerate in the folj lowing situations:'yFor pedestrians or similarly slow-moving
road users.'yFor red traffic lights.'yFor cross traffic.'yFor oncoming traffic.
Swervingvehicles
A vehicle driving in front of you is not detected until it is completely within the same lane as
your vehicle.
If a vehicle driving ahead of you suddenly
swerves into your lane, the system may not be able to automatically restore the selected disj
tance. It may not be possible to restore the sej
lected distance in certain situations, including if you are driving significantly faster than vehijcles driving ahead of you, for instance when
rapidly approaching a truck. When a vehicle
driving ahead of you is reliably detected, the
system requests that the driver intervene by
braking and carrying out evasive maneuvers, if
needed.
Cornering
If the desired speed is too high for a curve, the
speed is reduced slightly, although curves canj not be anticipated in advance. Therefore, drive
into a curve at an appropriate speed.
The system has a limited detection range. Sitj uations can arise in tight curves where a vehij
cle driving ahead will not be detected or will be
detected very late.
When you approach a curve the system may briefly report vehicles in the next lane due to
the bend of the curve. If the system decelerj
ates you may compensate it by briefly accelerj
ating.
After releasing the accelerator pedal the sysj tem is reactivated and controls speed indej
pendently.
Drivingaway In some situations, the vehicle cannot drive off
automatically; for example:
'yOn steep inclines.'yFrom bumps in the road.
In these cases, step on the accelerator pedal.
Seite 157DrivingcomfortControls157
Online Edition for Part no. 01402981185 - VI/17

Page 158 of 282

Weather
The following restrictions can occur under unj
favorable weather or light conditions:'yPoorer vehicle recognition.'yShort-term interruptions for vehicles that
are already recognized.
Examples of unfavorable weather or light conj
ditions:
'yWet conditions.'ySnowfall.'ySlush.'yFog.'yGlare.
Drive attentively, and react to the current traffic situation. If necessary, intervene actively, for
instance by braking, steering or evading.
Enginepower The desired speed is also maintained downhill,but may not be maintained on uphill grades if
engine power is insufficient.
Malfunction
The system cannot be activated if the radar
sensor is not aligned correctly. This may be
caused by damage incurred, for instance durj
ing parking.
A Check Control message is displayed if the system fails.
The function for detecting and responding when approaching stationary vehicles may be limited in the following situations:
'yDuring calibration of the camera immedijately after vehicle delivery.'yIf the camera is malfunctioning or dirty. ACheck Control message is displayed.Cruisecontrol
Theconcept Using this system, a desired speed can be adj
justed using the buttons on the steering wheel.
The system maintains the desired speed. The system accelerates and brakes automatically
as needed.
Generalinformation
Depending on the driving settings, the features of the cruise control can change in certain
areas.
Safetyinformation WARNING
The system does not relieve from perj
sonal responsibility to assess the traffic situaj tion. Based on the limits of the system, it canjnot independently react to all traffic situations.
There is a risk of an accident. Adjust driving
style to traffic conditions. Watch traffic closely
and actively intervene where appropriate.'

Page 159 of 282

Overview
ButtonsonthesteeringwheelPress butj
tonFunctionCruise control on/off, interruptj
ing, refer to page 159.Store/maintain speed, refer to
page 159.Resume speed, continue cruise
control, refer to page 160.Rocker switch:
Set speed, refer to page 160.
Switchingon/offandinterrupting
cruisecontrol
Switchingon Press button on the steering wheel.
The marking in the speedometer is set to the
current speed.
The cruise control can be used.
DSC Dynamic Stability Control is switched on,
if necessary.
Switchingoff Press button on the steering wheel.
'yIf active: press twice.'yIf interrupted: press once.
The displays go out. The stored desired speed
is deleted.
Interruptingmanually When active, press the button.
InterruptingautomaticallyThe system is automatically interrupted in thefollowing situations:'yWhen the driver applies the brakes.'yWhen selector lever position D is disenj
gaged.'yDynamic Traction Control DTC is activated
or DSC Dynamic Stability Control is deactij vated.'yIf DSC Dynamic Stability Control interj
venes.'yWhen HDC Hill Descent Control is actij
vated.'yWhen SPORT+ is activated with Driving
Dynamics Control.
Settingthespeed
Maintaining/storingthespeed
Press the rocker switch while the system is inj terrupted.
When the system is switched on, the current
speed is maintained and stored as the desired
speed.
The stored speed is displayed in the speedomj
eter and briefly in the instrument cluster, refer
to page 160.
DSC Dynamic Stability Control is switched on,
if necessary.
The speed can also be stored bypressing a button.
Press button.
Seite 159DrivingcomfortControls159
Online Edition for Part no. 01402981185 - VI/17

Page 160 of 282

Changingthespeed
Press the rocker switch up or down repeatedly
until the desired speed is set.
If active, the displayed speed is stored and the vehicle reaches the stored speed when the
road is clear.
'yEach time the rocker switch is pressed to
the point of resistance, the desired speed increases or decreases by approx.
1 mph/1 km/h.'yEach time the rocker switch is pressed
past the resistance point, the desired
speed changes by a maximum of 5 mph/
10 km/h.
The maximum speed that can be set dej
pends on the vehicle.'yPressing the rocker switch to the resistj
ance point and holding it accelerates or dej
celerates the vehicle without requiring
pressure on the accelerator pedal.
After the rocker switch is released, the vej
hicle maintains its final speed. Pressing the
switch beyond the resistance point causes
the vehicle to accelerate more rapidly.
Continuingcruisecontrol
Generalinformation
An interrupted cruise control can be continued
by calling up the stored speed.
Make sure that the difference between current speed and stored speed is not too large before
calling up the stored speed. Otherwise, uninj
tentional braking or accelerating may occur.
In the following cases, the stored speed value
is deleted and cannot be called up again:'yWhen the system is switched off.'yWhen the ignition is switched off.
Callingupstoredspeed
Press button.
The stored speed is reached and maintained.
Displaysintheinstrumentcluster
Indicatorlamp Depending on how the vehicle is equipjped, the indicator lamp in the instruj
ment cluster indicates whether the sysj
tem is switched on.
Desiredspeedandstoredspeed
'yMarking lights up green:
system is active, the markj
ing indicates the desired
speed.'yMarking lights up orange:
system is interrupted, the
marking indicates the stored
speed.'yThe marking does not light up: the system is switched off.
With instrument display: the symbol isdisplayed in the speedometer similarly to the mark for the desired speed.
Briefstatusdisplay Selected desired speed.
If no speed is indicated, it is possible that the
conditions necessary for operation are not curj rently fulfilled.
Seite 160ControlsDrivingcomfort160
Online Edition for Part no. 01402981185 - VI/17

Page:   < prev 1-10 ... 111-120 121-130 131-140 141-150 151-160 161-170 171-180 181-190 191-200 ... 290 next >