ECU BUICK CENTURY 2000 User Guide

1-48

If your vehicle doesn't have the child restraint
locking feature on the shoulder belt retractor,
tighten the belt by pulling up on the shoulder belt
while you push down on the child restraint. If
you're using a forward
-facing child restraint you
may find it helpful to use your knee to push down
on the child restraint as you tighten the belt.
5. Push and pull the child restraint in different
directions to be sure it is secure.
To remove the child restraint, just unbuckle the vehicle's
safety belt and let it go back all the way. The safety belt
will move freely again and be ready to work for an adult
or larger child passenger.
Securing a Child Restraint in the Center
Rear Seat Position
You'll be using the lap belt. Be sure to follow the
instructions that came with the child restraint. Secure
the child in the child restraint when and as the
instructions say.
CAUTION:
A child in a child restraint in the center front seat
can be badly injured or killed by the right front
passenger air bag if it inflates. Never secure a
child restraint in the center front seat. It's always
better to secure a child restraint in the rear seat.
You may secure a forward
-facing child restraint
in the right front passenger seat, but before you
do, always move the front passenger seat as far
back as it will go. It's better to secure the child
restraint in a rear seat.
See the earlier part about the top strap if the child
restraint has one.

1-49
1. Make the belt as long as possible by tilting the latch
plate and pulling it along the belt.
2. Put the restraint on the seat.
3. Run the vehicle's safety belt through or around the
restraint. The child restraint instructions will show
you how.4. Buckle the belt. Make sure the release button is
positioned so you would be able to unbuckle the
safety belt quickly if you ever had to.
5. To tighten the belt, pull its free end while you push
down on the child restraint. If you're using a
forward
-facing child restraint, you may find it
helpful to use your knee to push down on the child
restraint as you tighten the belt.
6. Push and pull the child restraint in different
directions to be sure it is secure.

1-50
To remove the child restraint, just unbuckle the vehicle's
safety belt. It will be ready to work for an adult or larger
child passenger.
Securing a Child Restraint in the Right
Front Seat Position
Your vehicle has a right front passenger air bag. Never
put a rear
-facing child restraint in this seat. Here's why:
CAUTION:
A child in a rear-facing child restraint can be
seriously injured or killed if the right front
passenger's air bag inflates. This is because the
back of the rear
-facing child restraint would be
very close to the inflating air bag. Always secure
a rear
-facing child restraint in the rear seat.
Although a rear seat is a safer place, you can secure a
forward
-facing child restraint in the right front seat.
You'll be using the lap
-shoulder belt. See the earlier
part about the top strap if the child restraint has one.
Be sure to follow the instructions that came with the
child restraint. Secure the child in the child restraint
when and as the instructions say.

1-51
1. Because your vehicle has a right front passenger air
bag, always move the seat as far back as it will go
before securing a forward
-facing child restraint.
(See ªSeatsº in the Index.)
2. Put the restraint on the seat.
3. Pick up the latch plate, and run the lap and shoulder
portions of the vehicle's safety belt through or
around the restraint. The child restraint instructions
will show you how.
Tilt the latch plate to adjust the belt if needed.
If the shoulder belt goes in front of the child's face or
neck, put it behind the child restraint.
4. Buckle the belt. Make sure the release button is
positioned so you would be able to unbuckle the
safety belt quickly if you ever had to.

1-53

If your vehicle has the child restraint locking
feature on the shoulder belt retractor, pull the
rest of the shoulder belt all the way out of the
retractor to set the lock.
To tighten the belt, feed the shoulder belt back
into the retractor while you push down on the
child restraint. You may find it helpful to use
your knee to push down on the child restraint as
you tighten the belt.

If your vehicle doesn't have the child restraint
locking feature on the shoulder belt retractor,
tighten the belt by pulling up on the shoulder belt
while you push down on the child restraint. You
may find it helpful to use your knee to push down
on the child restraint as you tighten the belt.
6. Push and pull the child restraint in different
directions to be sure it is secure.
To remove the child restraint, just unbuckle the vehicle's
safety belt and let it go back all the way. The safety belt
will move freely again and be ready to work for an adult
or larger child passenger.

2-5 Power Door Locks
Press the power door lock
switch to lock or unlock
all doors.
The rear doors do not have power door lock switches.
There is a lever which is used to manually lock or
unlock that door. It won't lock or unlock all the doors.
Programmable Automatic Power
Door Locks
Programmable automatic power door locks is a standard
feature that is intended to provide enhanced security and
convenience by automatically locking and unlocking
doors. This feature provides four operating modes. For
your vehicle, you may select and program one of the
following four operating modes:Mode 1: No automatic door lock or unlock.
Mode 2: Automatic all
-door lock when the transaxle is
shifted out of PARK (P); no automatic door unlock.
Automatic door relock when any door is unlocked,
opened and then all doors are again closed while the
vehicle is not in PARK (P) or NEUTRAL (N) and the
driver's foot is on the brake pedal.
Mode 3: Automatic all
-door lock when the transaxle is
shifted out of PARK (P). Automatic all
-door unlock
when the transaxle is shifted into PARK (P). Automatic
door relock when any door is unlocked, opened and then
all doors are again closed while the vehicle is not in
PARK (P) or NEUTRAL (N) and the driver's foot is on
the brake pedal.
Mode 4: Automatic all
-door lock when the transaxle is
shifted out of PARK (P). Automatic driver's door only
unlock when the transaxle is shifted into PARK (P).
Automatic door relock when any door is unlocked,
opened and then all doors are again closed while the
vehicle is not in PARK (P) or NEUTRAL (N) and the
driver's foot is on the brake pedal.

2-6
The operating mode of the programmable automatic
power door locks will be changed when the driver
performs the following:
1. Turn the ignition key to RUN.
2. Close all of the doors.
3. Apply your regular brakes.
4. Press and hold the power door lock switch. While
holding the door lock switch, move the shift lever
out of and back into PARK (P).
After an initial transaxle cycle, each additional cycle
will advance the operating mode by one, starting from
the current operating mode. During this procedure, the
automatic door lock and unlock functions will operate as
defined by each mode listed previously, providing the
driver with feedback of the current operating mode. If
cycled beyond Mode 4, the vehicle will enter operating
Mode 1. When the door lock switch is released, the
vehicle will remain in the most recent operating mode.
Disconnecting the vehicle's battery for up to a year will
not change the programmed mode of the programmable
automatic power door locks.Rear-Door Child Security Locks
Your vehicle is equipped
with rear
-door child
security locks that help
prevent passengers from
opening the rear doors of
your vehicle from the
inside. To use one of
these locks:
1. Open one of the rear doors.
2. On the inside of the rear door will be a lock. Insert
your key into this lock and turn it upward. This will
engage the safety lock. To disengage the feature, turn
the lock downward.
3. Close the door.
4. Do the same thing to the other rear door lock.
The rear doors of your vehicle cannot be opened from the
inside when this feature is in use. If you want to open the
rear door when the security lock is on, unlock the door
from the inside and then open the door from the outside.

2-9
Instant Alarm
This feature allows you to activate an alarm by pressing
a button on the remote keyless entry transmitter. Your
ignition must be off for the instant alarm to work. When
you press the horn button on the remote keyless entry
transmitter, the headlamps will flash, the horn will honk
repeatedly, and the interior lamps will illuminate,
attracting attention if you need it. The alarm will
continue until:

You press the alarm button on the remote keyless
entry transmitter a second time,

the ignition is in RUN, or

an alarm period of about two minutes has elapsed.
Security Feedback
Security feedback provides audible and/or visible
feedback that a remote keyless entry lock or unlock
command has been received and executed. Your ignition
must be off for this feature to work.You may select one of four operating modes for
reception of a lock command. You may also select one
of four operating modes for reception of an unlock
command. The selection and programming of the lock
and unlock operating modes are independent of each
other. The following modes are available for either lock
or unlock verification:
Mode 1: No Verification
Mode 2: Horn Chirp only
Mode 3: Headlamp Flash only
Mode 4: Horn Chirp and Headlamp Flash
The operating mode of the security feedback
lock feature will be changed when you perform
the following:

Turn the ignition key to RUN.

Close all the doors.

Press and hold the power door lock switch.

While holding the door lock switch, press
and release the remote keyless entry transmitter
lock button.

2-10
This will start the customization mode. While in the
customization mode, the feature will sound the number
of chimes corresponding to the current security feedback
lock mode.
Each additional press of the remote keyless entry
transmitter LOCK button will cause your vehicle to
advance the lock mode by one, starting from the current
lock mode. If cycled beyond lock Mode 4, the vehicle
will enter lock Mode 1. During this procedure, the
feature will sound the number of chimes corresponding
to the current lock mode, providing you with feedback.
When the door lock switch is released, the vehicle will
remain in the most recent lock mode.
The operating mode of the security feedback unlock
feature will be changed when you perform the following
sequence with your vehicle's doors closed and the
ignition key in RUN:

Press and hold the power door unlock switch. While
holding the door unlock switch, press and release the
remote keyless entry transmitter unlock button. This
will start the customization mode.

While in the customization mode, the feature will
sound the number of chimes corresponding to the
current unlock mode.Each additional press of the remote keyless entry
transmitter unlock button will cause your vehicle to
advance the UNLOCK mode by one, starting from the
current unlock mode. If cycled beyond unlock Mode 4,
the vehicle will enter unlock Mode 1. During this
procedure, the feature will sound the number of chimes
corresponding to the current unlock mode, providing
you with feedback. When the door unlock switch is
released, the vehicle will remain in the most recent
unlock mode.
Disconnecting the vehicle's battery for up to a year will
not change the programmed mode of the lock and
unlock security feedback features.
Delayed Locking
Delayed locking allows the doors to be locked while
passengers are exiting the vehicle. This feature also
provides a brief time period after all the doors are
closed, but before the doors are locked, in which the
doors may be reopened. Delayed locking is user
programmable for enabling or disabling the feature.

2-12
Illumination on Remote Activation
This feature provides interior lighting when a remote
keyless entry door unlock command is received and
executed by your vehicle. Your ignition must be off for
the illumination on remote activation feature to work.
The interior lamps will light until either the ignition is
turned to RUN or a period of 40 seconds has elapsed.
If a door is opened during the illumination period, the
timed lighting will be canceled, and the interior lamps
will remain on since a door is open.
Matching Transmitter(s) To Your Vehicle
Each remote keyless entry transmitter is coded to
prevent another transmitter from unlocking your vehicle.
If a transmitter is lost or stolen, a replacement can be
purchased through your dealer. Remember to bring any
remaining transmitters with you when you go to your
dealer. When the dealer matches the replacement
transmitter to your vehicle, any remaining transmitters
must also be matched. Once your dealer has coded the
new transmitter, the lost transmitter will not unlock your
vehicle. Each vehicle can have only four transmitters
matched to it.
Battery Replacement
Under normal use, the battery in your remote keyless
entry transmitter should last about three years.
You can tell the battery is weak if the transmitter won't
work at the normal range in any location. If you have to
get close to your vehicle before the transmitter works,
it's probably time to change the battery.
NOTICE:
When replacing the battery, use care not to
touch any of the circuitry. Static from your
body transferred to these surfaces may
damage the transmitter.