CD player BUICK LACROSSE 2006 Get To Know Guide

11
To set Bass/Treble, push and release
until “BAS” or “TRE” appears. Turn to
increase or decrease. To adjust to the
middle position, press and hold until it
beeps.
To set Balance/Fade, push and release
until “BAL” appears to adjust Balance.
Turn the knob to move the sound toward
the right or left. Push until “FAD” appears
toadjust Fade. Turn the knob to move
the sound toward the front or rear.
To adjust all controls to the middle posi
tion, push/hold the speaker knob when
no tone or speaker control is displayed.
“ALL CEN” appears and the unit beeps.
(Seek):Press and release the
left/right Seek arrow to go to the previ
ous or next station and stay there.
Toscan, press and hold either arrow for
more than two seconds. “SCAN”
appears on the display and a beep
sounds. The radio finds a station, playsafew seconds and advances to the
next. Press either arrow or a pushbutton
to stop scanning.
Toscan preset stations, press and hold
either arrow for more than four seconds.
“PSCAN” appears and two beeps
sound. Press either arrow or a push
button to stop scanning presets.
Setting Preset Stations:
1. With the radio on, press BAND to
select AM/FM1/FM2 or XM1/XM2
(if equipped).
2. Tune to the desired station.
3. Press EQ to select equalization.
4.Press and hold a numbered push
button until a beep sounds.
Repeat for each pushbutton for each
band (up to 30 possible stations).
CD Controls
With the ignition on, insert a CD, label
side up, partway into the slot. The player
will pull it in and begin playing. To insert
with ignition off, first press eject or DISP.
1 (Reverse):Press to go to the start
of the current track if more than eight
seconds have played. Hold or press
more than once to move backward
through the CD tracks.
2 (Fast Forward):Press to go to
the next track. Hold or press more than
once to forward through the upcoming
CD tracks.
4RDM (Random):Press to hear tracks
in random order.Press again to disable
random play.
(Seek):Press the left arrow to go
to the start of the current track or the
previous track. Press the right arrow to
go to the start of the next track. Press
the arrows for more than two seconds to
search previous or next tracks. Release
to stop searching and play the track.
DISP (Display):Press to display the
current CD track and the elapsed time
the current track has played.
BAND:Press to switch to the radio
when a CD is playing. The CD remains
inside the player.
(CD):Press to play a CD when the
radio is playing.
EQ (if equipped): Press to select cus
tomized equalization settings for C&W,
Jazz, Talk, Pop, Rock and Classical
music. To return to manual mode,
press and release the Tone knob until
“MANUAL” is displayed.
(Eject):Press to eject a CD, with the
ignition off or on, or the radio off. Load
CDs with the ignition off by pressing this
button first.

Getting to Know YourLaCrosse12
MP3Capable Uplevel Radio
(if equipped)
Play MP3 files on CDR CDs of up to
700MB capacity. To play, with the igni
tion on, insert the disc partway into the
slot, label side up. The player will pull it
in. “READING” appears on the display
and the disc plays. Smaller, 3inch
(8cm) single CDs may be used with
an adapter ring.
3 (Repeat):Press to hear a track
over again. RPT is displayed. Press
again to disable repeat play.
5 (Previous Folder):Press to go to
the first track in the previous folder.
Pressing while in the Folder Random
mode takes you to the previous folder
and plays random tracks there.
6(Next Folder):Press to go to the
first track in the next folder. Pressing
while in Folder Random mode takes you
to the next folder and plays random
tracks there.
SixDisc CD Player (if equipped)
To load multiple CDs in the sixdisc
CD player:
1.Turn the ignition on. Press and hold
the Load button for two seconds. The
player beeps and the light to the right
of the slot will flash. “MULTI LOAD #”
is displayed.
2.When the light stops flashing and
turns green, “INSERT CD #” is
displayed. Insert a disc partway,
label side up.
3. The indicator light will begin blinking
and turn green. Another disc may be
loaded.
4. When loading two to five CDs, press
the Load button again after loading
the final CD.
For every CD loaded, a number appears
on the radio display. To play a specific
disc, press CD and the number of the
CD you want to hear. A small bar
appears under the CD number that is
playing, and the track number appears.
Finding a Category Station
(if equipped)
Category (CAT) stations are available on
XM1 or XM2 bands only.To find a CAT
station:
1.Press the CAT button to activate
Program Type (PTY) Select mode.
2.A category is displayed.
3. Rotate the Tune knob. When the
preferred category appears, press the
Seek button to go to the first category
station (pressing Seek for more than
two seconds will activate Category
Scan).
4. To go to another station, press the
CAT button. The previously stored
category will be displayed.
5. Press the up or down Seek button.
6.Press the CAT button to exit Program
Type Select mode.
Note:CDs with any labels may jam in
the CD player. Label a CD using a
permanent marker. If more than one CD
is inserted into the slot at one time, or if
scratched or damaged CDs are played,
the CD player could be damaged. When
using the CD player, use only CDs in
good condition without added labels;
load one CD at a time; and keep the CD
player and the loading slot free of for
eign materials, liquids and debris.