ignition BUICK LACROSSE 2006 Get To Know Guide

Getting to Know YourLaCrosse4
Driver Information Center (DIC)E/M (English/Metric):On the base DIC,
press to choose English or Metric units.
On uplevel DICs, press the (Option)
button until “UNITS” appears. Press the
(Set/Reset) button to choose English
or Metric units.
(Set/Reset)(if equipped): Press to
set/reset certain functions and to turn
off/acknowledge DIC messages.
(Gauges)(if equipped): Press to dis
play battery and oil life. To reset the Oil
Life System after an oil change, press
and hold the button while “OIL LIFE”
is displayed until it shows 100%.
(Fuel)(if equipped): Press to display
fuel range, average economy and
instantaneous economy.
(Option)(if equipped): Press to dis
play English/Metric units, language,
personalization, compass zone and
compass calibration.
(Traction Control)(if equipped):
Press to turn traction control on or off.
(Hazard):Press to turn the hazard
warning flashers on or off.
Personalizing the DIC (if equipped)
Uplevel DICs can memorize selected
personalized settings for up to two
drivers. (Some features are limited to a
single setting.)
1. Place the vehicle in Park (P) and turn
on the ignition.
2. Press the (Option) button until
“PERSONAL PROGRAM” is
displayed.
3. Press the (Set/Reset) button
to display instructions.
4.Press the button to display
programmable features.
5. Press the button to change the
setting of each feature.
The baselevel Driver Information
Center (DIC) displays the odometer and
trip odometer. Uplevel DICs also displaya compass, trip computer, fuel economy
information, OnStar
®phone numbers
called (if equipped) and other messages
or warnings. The DIC display is located
on the instrument cluster below the
speedometer, and can be programmed
in English, French or Spanish.
Outside temperature displays in the
bottomright corner of the uplevel DIC
when viewing the trip/odometer screens,
fuel screens and some gauge screens.At 37ºF (3ºC) or below, readings toggle
between temperature and the word
“ICE” for two minutes.
The following DIC controls are located
on the center of the instrument panel:
TRIP/ODO (Trip/Odometer):On the
base DIC, press to display odometer/trip
distance. Uplevel DICs also display time
elapsed and average speed.

5
Your ignition key identifies you to the
vehicle.Two keys can be programmed
for certain features that correspond to
each driver. To personalize a key:
1. From the Personal Program menu,
press the (Option) button until
“PERSONALIZE KEY” is displayed.
2. Press the (Set/Reset) button until
“YES” is displayed.
3. Press the button.
Personalization Features include:
•
Delayed Locking—Delays locking
of the vehicle doors for up to five
seconds after the last door is closed.Two chimes will sound when the
power door lock switch or the Lock
button on the Remote Keyless Entry
transmitter is pressed when a door is
open. To program:
1. From the Personal Program menu,
press the (Option) button until
“DELAYED LOCKING” is displayed.
2. Press the (Set/Reset) button until
“ON” or “OFF” appears.
3. Press the button to select it.
The ignition key must be removed for
the feature to work after programming.
•
Key Fob Feedback—Choose from
Off (no feedback), Lights (exterior
lights flash) or Lights and Horn when
you press the Remote Keyless Entry
transmitter (key fob) Lock button. To
program:
1. From the Personal Program menu,
press the (Option) button until
“FOB LOCK FEEDBACK” is displayed.
2. Press the (Set/Reset) button until
the desired setting is displayed.
3.Press the button to save the
setting.•
Exterior Light Delay—Sets the
time for exterior lights to remain on
after the key is removed from the
ignition or the vehicle is unlocked with
the Remote Keyless Entry transmitter.
To program:
1. From the Personal Program menu,
press the (Option) button until
“EXT LIGHT DELAY” is displayed.
2. Press the (Set/Reset) button to
scroll through OFF or 15/30/60/90
second delays.
3. Press the button to store a setting.
You can also use the (Option) and
(Set/Reset) buttons to personalize
each of the following:
• Return settings to factory
default/reset all keys
• Interior lights on when key is
removed from the ignition
• Content theftdeterrent system on/off
• Remote start on/off
• Personalize/replace key
• Personalize radio stations
• Auto door lock on/off
• Auto door unlock all/driver’s door/off
• Key fob unlock driver’s door/all doors
on first press
Exiting Programming Mode:The DIC
exits programming mode when:
•The vehicle is shifted out of Park.
• The vehicle is no longer in Run.
• You reach the end of the Personal
Program menu.
See Section 3 of your Owner Manual.

7
(Headlamps):The headlamps posi
tion manually activates the headlamps,
exterior tail/marker lamps and instrumentpanel/radio lights.
(Fog Lamps):To activate the fog
lamps, press the center of the rotary
control marked .
To switch headlamps from low to high
beam, push the multifunction lever away
from you. Pull it back and release for
lowbeam operation.
See Section 3 of your Owner Manual.
Daytime Running Lamps (DRL)
DRL illuminates the lowbeam head
lamps at a lower intensity in daylight to
make the front of the vehicle more visi
ble to others. The DRL illuminates only
the lowbeam headlamps, not the
taillamps or side marker lamps.
See Section 3 of your Owner Manual.
Interior Lamps
The interior lamps control is located next to
the exterior lamps control on the left side
of the instrument panel. It can be set to:
(Off):This position disables the interi
or lamps entirely,whether or not a door
is open.
(Door):This position turns on the
interior lamps when a door is opened
and when the ignition key is removed.
(On):This position turns on the
interior lamps continuously.
Instrument Panel Brightness:When
you push the center of the interior lamps
knob, a springloaded stem will pop out.
Turn it right or left to adjust intensity.
Reading Lamps:Press the reading light
lens to turn on/off.
See Section 3 of your Owner Manual.
Tilt/Telescoping Steering Wheel
To adjust the tilt position of the steering
wheel, hold the wheel and pull the lever
(see “A”) on the left of the steering col
umn toward you. Move the wheel up or
down to a comfortable level. Release
the lever to lock.
To adjust the telescoping position of the
steering wheel, push down on the lever
(see “B”) to unlock the steering wheel.
Pull or push the steering wheel to the
desired position. Push up on the lever to
lock the steering wheel.
Do not adjust the position of the steering
wheel while driving.
See Section 3 of your Owner Manual.
A
B

9
(Temperature):Press to manually
adjust the temperature. The left side
controls the driver side and the right
side controls the passenger side.
(Decrease Fan Speed):Press to
lower fan speed.
(Increase Fan Speed):Press to
raise fan speed.
(Air Conditioning):Press to activate
or deactivate air conditioning.
(Recirculation):Press to prevent
outside air from entering your vehicle.
Recirculation can be activated in Vent or
BiLevel mode, but not in Floor/Defog or
Defrost mode.
(Rear Window Defog):Press to
clear the rear glass (it turns off after
about 20 minutes). Press again for
extended operation. Press again or
switch off the ignition to turn off.
(Floor mode):Press to direct most
of the air to the floor.
(BiLevel mode):Press to direct
most of the air to the instrument panel
and floor outlets.
(Vent mode):Press to direct air
through the instrument panel outlets.
(Floor/Defog):Press to clear the
windshield and front side windows of
mist and frost.
(Defrost):Press to clear the wind
shield of heavier amounts of mist and
frost more quickly.
(Heated Seats):Press to turn the
driver or passenger heated seat on/off.
See Section 3 of your Owner Manual.
(Mist):For a single wipe, twist the
band on the multifunction stalk down to
this position and release.
(Off):Twist the band to this position
to turn off the wipers.
(Delay):Twist the band up to set the
delay time (the top of the band equals a
shorter delay).
(Low):Twist the band up to this
position for lowspeed wipers.
(High):Twist the band up to this
position for highspeed wipers.
(Washer):To spray washer fluid,
turn the paddle at the top of the multi
function lever forward and release.
There will be a slight delay before the
wipers are activated. This is normal and
allows the washer to clean the entire
windshield.
See Section 3 of your Owner Manual.
Windshield Wipers/Washers

Getting to Know YourLaCrosse10
Audio Systems
Setting the Time
Press and hold the “H” button on the
sound system faceplate until the correct
hour appears on the display. Press and
hold M until the correct minute appears.
The ignition does not need to be turned
on.
Radio Controls
(Power):
Press to turn the system on
and off.
(Volume):Turn to increase/decrease
volume.
BAND:Press to switch between AM,
FM1/FM2 and XM1/XM2 (if equipped).
DISP (Display): Press to switch the dis
play between the radio station frequency
and the time. With the ignition off, press
to display the time.
While in XM mode (if equipped), press
to display the artist, song title, category
and channel.
INFO (Information) (if equipped): While
in XM mode (if equipped), press to dis
play a current radio station message
and other information, if available.
SCV (Speed Compensated Volume):Press to select Off, Min, Med or Max
radio volume compensation as vehicle
speed increases.
(Tune/Balance/Fade):Turn to select
radio stations.
Cruise Control
The cruise control buttons are located
on the steering wheel.
(On/Off):Push to turn the system on
or off, or to deactivate.
SET (Set/Decelerate):To set cruise
control, press the button and acceler
ate to the desired speed. Press the
SETbutton and release the accelerator.
To decrease speed when cruise is
active, press and hold the SET buttonto reach the desired speed.
• Press SET once and release to
decrease speed by 1 mph.
RES+ (Resume/Accelerate):After
setting a cruise speed and later braking
for conditions, push the RES+ button to
resume the set speed.
To increase speed from a previous
setting, press and hold the RES+ button
to reach the desired speed or use the
accelerator.
• Press RES+ once and release to
increase speed by 1 mph.
See Section 3 of your Owner Manual.

11
To set Bass/Treble, push and release
until “BAS” or “TRE” appears. Turn to
increase or decrease. To adjust to the
middle position, press and hold until it
beeps.
To set Balance/Fade, push and release
until “BAL” appears to adjust Balance.
Turn the knob to move the sound toward
the right or left. Push until “FAD” appears
toadjust Fade. Turn the knob to move
the sound toward the front or rear.
To adjust all controls to the middle posi
tion, push/hold the speaker knob when
no tone or speaker control is displayed.
“ALL CEN” appears and the unit beeps.
(Seek):Press and release the
left/right Seek arrow to go to the previ
ous or next station and stay there.
Toscan, press and hold either arrow for
more than two seconds. “SCAN”
appears on the display and a beep
sounds. The radio finds a station, playsafew seconds and advances to the
next. Press either arrow or a pushbutton
to stop scanning.
Toscan preset stations, press and hold
either arrow for more than four seconds.
“PSCAN” appears and two beeps
sound. Press either arrow or a push
button to stop scanning presets.
Setting Preset Stations:
1. With the radio on, press BAND to
select AM/FM1/FM2 or XM1/XM2
(if equipped).
2. Tune to the desired station.
3. Press EQ to select equalization.
4.Press and hold a numbered push
button until a beep sounds.
Repeat for each pushbutton for each
band (up to 30 possible stations).
CD Controls
With the ignition on, insert a CD, label
side up, partway into the slot. The player
will pull it in and begin playing. To insert
with ignition off, first press eject or DISP.
1 (Reverse):Press to go to the start
of the current track if more than eight
seconds have played. Hold or press
more than once to move backward
through the CD tracks.
2 (Fast Forward):Press to go to
the next track. Hold or press more than
once to forward through the upcoming
CD tracks.
4RDM (Random):Press to hear tracks
in random order.Press again to disable
random play.
(Seek):Press the left arrow to go
to the start of the current track or the
previous track. Press the right arrow to
go to the start of the next track. Press
the arrows for more than two seconds to
search previous or next tracks. Release
to stop searching and play the track.
DISP (Display):Press to display the
current CD track and the elapsed time
the current track has played.
BAND:Press to switch to the radio
when a CD is playing. The CD remains
inside the player.
(CD):Press to play a CD when the
radio is playing.
EQ (if equipped): Press to select cus
tomized equalization settings for C&W,
Jazz, Talk, Pop, Rock and Classical
music. To return to manual mode,
press and release the Tone knob until
“MANUAL” is displayed.
(Eject):Press to eject a CD, with the
ignition off or on, or the radio off. Load
CDs with the ignition off by pressing this
button first.

Getting to Know YourLaCrosse12
MP3Capable Uplevel Radio
(if equipped)
Play MP3 files on CDR CDs of up to
700MB capacity. To play, with the igni
tion on, insert the disc partway into the
slot, label side up. The player will pull it
in. “READING” appears on the display
and the disc plays. Smaller, 3inch
(8cm) single CDs may be used with
an adapter ring.
3 (Repeat):Press to hear a track
over again. RPT is displayed. Press
again to disable repeat play.
5 (Previous Folder):Press to go to
the first track in the previous folder.
Pressing while in the Folder Random
mode takes you to the previous folder
and plays random tracks there.
6(Next Folder):Press to go to the
first track in the next folder. Pressing
while in Folder Random mode takes you
to the next folder and plays random
tracks there.
SixDisc CD Player (if equipped)
To load multiple CDs in the sixdisc
CD player:
1.Turn the ignition on. Press and hold
the Load button for two seconds. The
player beeps and the light to the right
of the slot will flash. “MULTI LOAD #”
is displayed.
2.When the light stops flashing and
turns green, “INSERT CD #” is
displayed. Insert a disc partway,
label side up.
3. The indicator light will begin blinking
and turn green. Another disc may be
loaded.
4. When loading two to five CDs, press
the Load button again after loading
the final CD.
For every CD loaded, a number appears
on the radio display. To play a specific
disc, press CD and the number of the
CD you want to hear. A small bar
appears under the CD number that is
playing, and the track number appears.
Finding a Category Station
(if equipped)
Category (CAT) stations are available on
XM1 or XM2 bands only.To find a CAT
station:
1.Press the CAT button to activate
Program Type (PTY) Select mode.
2.A category is displayed.
3. Rotate the Tune knob. When the
preferred category appears, press the
Seek button to go to the first category
station (pressing Seek for more than
two seconds will activate Category
Scan).
4. To go to another station, press the
CAT button. The previously stored
category will be displayed.
5. Press the up or down Seek button.
6.Press the CAT button to exit Program
Type Select mode.
Note:CDs with any labels may jam in
the CD player. Label a CD using a
permanent marker. If more than one CD
is inserted into the slot at one time, or if
scratched or damaged CDs are played,
the CD player could be damaged. When
using the CD player, use only CDs in
good condition without added labels;
load one CD at a time; and keep the CD
player and the loading slot free of for
eign materials, liquids and debris.

13
Universal Home Remote
TheUniversal Home Remote can store
three frequencies for a garage door
opener, entry door lock, security system,
etc. The remote requires the vehicle’s
engine to be running or the ignition to be
in the Run position in order to operate.
This provides added security by not
allowing access to the home, garage,
etc., through the Universal Home
Remote without having the proper key
for the vehicle.
To program, with the key On and the
engine Off:
• Press and hold the two outer buttons
on the remote until the indicator light
flashes;
then release the buttons(about 20 seconds — do not hold for
more than 30 seconds); do not repeat
this step for the second or third
devices added.
• Hold the end of your handheld trans
mitter up to three inches away from
the surface of the remote. Hold its
button and the button you wish to
assign it to on the Universal Home
Remote.
• Continue holding both buttons (up to
90 seconds); the indicator light will
begin blinking slowly, then more quick
ly. Programming is complete when
the remote light flashes rapidly.
• Release both buttons.
• Press and hold the remote button
again. If the indicator stays lit con
stantly, programming is complete.
• Continue programming additional
devices using the remaining two
Universal Home Remote buttons, but
do not simultaneously press the two
outer buttons on the remote again.
If the remote indicator blinks rapidly for
two seconds and remains on during pro
gramming, it indicates that your device
(usually a garage door opener) has a
“rolling code.”
See Section 2 of your Owner Manual.
Steering Wheel Controls (if equipped)
See Radio and CD Controls for full details
about the functions of the following buttons:
•
(Seek)
•BAND
•1–6 (Preset Stations)
•(OnStar®/Mute):Press to silence
audio, and again to play. In OnStar
equipped vehicles, press to interact
with the OnStar system.
•
(VOLUME):Press up/down
arrow to increase/decrease volume.
See Section 3 of your Owner Manual.

Getting to Know YourLaCrosse18
Vehicle Symbols Glossary
Following are examples of symbols you
may find on your vehicle. It is important
to become familiar with them, as they
indicate vehicle features and alert you
to various vehicle operating conditions.
Air Bag Readiness Light
Air Conditioning (A/C)
Air Recirculation
Antilock Brake System
Warning Light
Brake System Warning Light
Cruise Control On/Off
DIC Fuel
DIC Gauges
DIC Option
DIC Set/Reset
Fog Lamps
Headlamps
Malfunction Indicator Lamp
(Check Engine Light)
Off
Off/On
On
Parking Lamps
Rear Window Defogger
Remote Vehicle Start
Safety Belt Reminder Light
Security Light
Traction Control Off Light
StabiliTrak®–Stability Control
System (if equipped)
StabiliTrak is a computercontrolled sys
tem that detects and corrects differences
between the path you have chosen and
the vehicle’s actual direction by applying
brake pressure individually at the appro
priate wheel. When the system acti
vates, “STABILITY CONTROL ACTIVE”
displays on the DIC.
See Section 4 of your Owner Manual.
Acoustic Laminate Glass
Special windshield and front door win
dow glass composition reduces wind
and road noise. If replacement is neces
sary, see your dealer or specify
acoustic
laminateglass from the supplier. Failure
to do so can result in added wind and
outside noise in the cabin.
Automatic Transaxle Shift Lock
If the battery fails and it is necessary
to move the vehicle, the Automatic
Transaxle Shift Lock can be disabled to
allow the transaxle to be shifted out of
Park. Turn the ignition key to ACC posi
tion, and shift the transaxle into Neutral.With the car in Neutral, the vehicle can
be pushed out of a confined area.
See Sections 2 and 5 of your Owner Manual.