ECO mode BUICK LESABRE 2002 User Guide

2-64 Training a Garage Opener with a ªRolling
Codeº Feature (If Equipped)
If you have not previously programmed the hand-held
transmitter to HomeLink, see ªProgramming the
HomeLink Transmitterº listed previously. If you have
completed this programming already, you now need to
train the garage door opener motor head unit to
recognize HomeLink.
1. Find the ªLearnº or ªSmartº button on the garage
door opener motor head unit. The exact location and
color will vary by garage door opener brand. If you
have difficulty finding the ªLearnº or ªSmartº
button, refer to your garage door opener owner's
manual or contact the manufacturer of HomeLink
at 1
-800-355-3515, or on the internet
at www.homelink.com.
Because of the steps involved, it may be helpful
to have another person assist in programming
the transmitter.2. Press the ªLearnº or ªSmartº button on the garage
door opener motor head unit. An indicator light will
begin to flash when the motor head unit enters the
training mode.
Following this step, you have 30 seconds to
start Step 3.
3. Return to HomeLink in your vehicle and firmly
press and release the programmed HomeLink
button three times.
The rolling
-code garage door opener should now
recognize HomeLink. You may either use HomeLink or
the hand
-held transmitter to open the garage door.
If after following these instructions, you still have
problems training the garage door opener, contact the
manufacturer of HomeLink at 1
-800-355-3515, or on
the internet at www.homelink.com.

2-83
FUEL INFO (Information): Press this button to
display fuel information.
Press the FUEL INFO button until the display shows
FUEL ECONOMY AVERAGE. Average fuel economy
is viewed as a long term approximation of your overall
driving conditions. To learn the average fuel economy
from a new starting point, press the RESET button while
the average fuel economy is displayed in the DIC.
Press the FUEL INFO button until the display
shows FUEL ECONOMY INST. Instantaneous fuel
economy varies with your driving conditions, such as
acceleration, braking and the grade of the road being
traveled. The RESET button does not function in
this mode.
Press the FUEL INFO button until the display shows
FUEL RANGE. The fuel range will calculate the
remaining distance you can drive without refueling. This
calculation is based on the average fuel economy for the
last 25 miles (40.25 km) driven, and the fuel remaining
in the fuel tank. The RESET button does not function in
this mode.GAGE INFO (Information): Use this button to display
oil pressure, oil life, coolant temperature, tire pressure
and battery information.
Press the GAGE INFO button until OIL PRESSURE
appears in the display. If there are no problems detected
with the oil pressure, the display will show OIL
PRESSURE NORMAL. If a low oil pressure condition
is detected, the display will show OIL PRESSURE
LOW. If you see the OIL PRESSURE LOW message,
your vehicle could be low on oil or the oil is not going
through the engine properly. See your dealer for service.
Press the GAGE INFO button until COOLANT TEMP
appears in the display. If there are no problems detected
with the temperature, COOLANT TEMP NORMAL
will appear in the display. If the temperature is too high,
COOLANT TEMP HOT will appear in the display.
If you see the COOLANT TEMP HOT message,
the engine is overheated. You should pull off the road,
stop your vehicle and turn off your engine as soon as
possible. This manual explains what to do. See ªEngine
Overheatingº in the Index.

2-87
Use the following steps for personal choice
programming instructions.
1. Turn the ignition on and keep the transaxle
in PARK (P).
2. Inform the DIC which driver you are by pressing
the button with the unlock symbol on your remote
keyless entry transmitter or the appropriate memory
seat control.
3. Press and hold the ENG/MET button for five
seconds. WELCOME TO BUICK OPTION
FEATURE will appear in the display.
4. The first choice to be made will be DRIVER ID 1
or 2. Press the ENG/MET button to toggle between
your selections within a display and RESET to
choose the current selection and move on to the
next personal choice feature.
If you would like to exit the selection mode without
moving through each of the personal choice features,
simply press a different button on the DIC or turn off the
ignition. Whatever personal choices you made will still
be retained, even without passing through each of the
features. In order for your personal choices to save, you
must press RESET after making your selections.If you happen to move past a selection you would like
to make a personal choice for, press the button with the
unlock symbol on your remote keyless entry transmitter
or press the appropriate driver number on the seat
control. This will return you to the beginning of the
option feature programming mode.
Automatic Door Locks
The door lock modes when shifting in and out of
PARK (P), can be changed through the DIC. You
can change these modes by different selections of the
following DIC displays:

AUTO DOOR LOCKS
-- OFF/ON

UNLOCK
-- OFF/ON

UNLOCK
-- KEY OFF/PARK

DOOR TO UNLOCK
-- DRIVER/ALL
If you choose OFF for AUTO DOOR LOCKS,
your door locks will operate normally with no
automatic feature.
If you choose ON for AUTO DOOR LOCKS, ON for
UNLOCK and KEY OFF, your doors will lock every
time you shift out of PARK (P), and the doors will
unlock every time you stop and turn the ignition to OFF.

2-89
Security Feedback
By choosing different combinations of these selections,
you can choose the type of transmitter activated
feedback when locking and unlocking your vehicle with
your transmitter. Each time you make a selection by
pressing the ENG/MET button, press the RESET
button to record your choice.

KEYLESS FEEDBACK
-- OFF/ON

LIGHTS FEEDBACK
-- OFF/ON

HORN FEEDBACK
-- OFF/ON
If you choose ON for KEYLESS FEEDBACK you will
also need to choose LIGHTS and/or HORN FEEDBACK.
You can select the following modes:

If you choose OFF for KEYLESS FEEDBACK,
you will receive no security feedback when locking
or unlocking your vehicle.

If you choose ON for KEYLESS FEEDBACK
and ON for LIGHTS FEEDBACK, the exterior
lamps will flash twice when unlocking your vehicle
and once when locking your vehicle.
If you choose ON for KEYLESS FEEDBACK
and ON for HORN FEEDBACK, your horn will
chirp when all doors are unlocked and when locking
your vehicle.

If you choose ON for KEYLESS, LIGHTS and
HORN FEEDBACK, your exterior lamps will flash
twice at the first unlock button press, your exterior
lamps will flash twice and the horn will chirp once at
the second unlock button press, and the exterior
lamps will flash and the horn will chirp once when
locking your vehicle.
For more information on this feature, see ªSecurity
Feedbackº in the Index.
Delayed Locking
This feature, which delays the actual locking of the
vehicle, can be made active or inactive through the DIC.
When DELAYED LOCKING
-- OFF/ON appears on
the display, use the ENG/MET button to toggle the
arrow between OFF and ON. When you have made your
choice, press the RESET button to record your selection.
For more information on this feature, see ªDelayed
Lockingº in the Index.

3-4 Dual Automatic ComforTemp
Climate Control (If Equipped)
TEMP (Temperature): To manually adjust the
temperature inside the vehicle, push the TEMP arrow.
Push the TEMP up arrow for warmer temperature
settings and the TEMP down arrow for cooler
temperature settings. The setting will be shown in the
display. The display will then return to the outside
temperature after a few seconds.
FAN: Pressing the FAN button will display and
hold the current fan speed while in manual mode.If you want the fan to run at a lower speed, push the
down arrow on the FAN button. The fan speed will
decrease with every push of the button until the lowest
speed is reached. If you want to increase the fan speed,
push the up arrow on the FAN button.
AIR FLOW: Pressing the AIR FLOW button will
display and hold the current setting while in manual
mode. Use the up and down arrows on the AIR FLOW
button to cycle through the available modes.

WINDSHIELD
-FLOOR: This setting directs
most of the airflow to the front windshield defroster
with some airflow to the side window defrosters and
floor ducts.

MID: This setting directs airflow through the
instrument panel outlets.

MID
-FLOOR: This setting directs airflow through
both the instrument panel outlets and the floor ducts.
There is also a small amount of air directed to the
front defroster and the side window defrosters.

FLOOR: This setting directs most of the airflow to
the floor ducts with some airflow directed to the side
window defrosters. There is also a small amount of
airflow directed to the front defroster.

3-5
OFF: If the passenger comfort control is turned on, it
can be turned off by pressing the OFF button once.
Pressing the OFF button a second time will turn off the
main system. Turning off the main system causes the fan
to turn off and the airflow to be directed toward the
floor. The system will still try to keep the interior of the
vehicle at the previously chosen temperature setting.
The outside temperature will show on the display when
the system is off.
The ventilation system always allows fresh air to flow
through your vehicle when the vehicle is moving even
when the system is off.
VENT (Flow
-Through Ventilation): The VENT
button allows outside air to flow through your vehicle
without the air conditioning compressor working. To
turn off the VENT selection, push the VENT button
again. If you select VENT while in FRONT defrost, the
VENT light will flash three times to let you know this is
not allowed. This is to prevent fogging.RECIRC (Recirculation): When RECIRC is selected,
the system will limit the amount of outside air entering
your vehicle. This is helpful when you are trying to cool
the interior of the vehicle quickly or limit the amount of
outside air entering your vehicle. RECIRC and AUTO
may be selected at the same time. The system will remain
in RECIRC until the ignition is turned off or the RECIRC
button is pressed again. RECIRC can be selected in all
manual airflow modes except FRONT defrost and VENT.
If you select RECIRC while in FRONT defrost, the
RECIRC light will flash three times to let you know this is
not allowed. This is to prevent fogging. FRONT: This selection is used to defrost
the windshield by directing the airflow toward the
windshield. To turn off FRONT, press the AUTO
or AIR FLOW button.
If the AIR FLOW up button is selected while in the
FRONT defrost mode, the system will direct the air
toward the windshield and the floor. If the AIR FLOW
down button is selected while in the FRONT defrost
mode, the system will direct the air toward the floor, and
the FRONT defrost mode will cancel.
FRONT defrost will work better if any ice or snow is
cleared from the hood and the air inlet area between the
base of the windshield and the hood.

3-7
Sun and temperature sensors automatically adjust the air
temperature, the airflow direction and the fan speed to
maintain your temperature setting. The system may
supply cooler air to the side of the vehicle toward the
sun. Be careful not to put anything over the sensor on
top of the dash.
The display will show fan speed, temperature level
setting and airflow direction for a few seconds whenever
AUTO is selected, and then it will display the outside
temperature. The outside temperature reading is most
accurate when the vehicle is moving. During stops, the
display shows the previous temperature for best
accuracy and system control.
To find your preferred temperature setting, start with the
system in AUTO mode and the TEMP button adjusted
to 75
F (24
C), give the vehicle about 20 minutes to
stabilize, and adjust your temperature setting if
necessary, by using the TEMP button. The display will
show the temperature setting for a few seconds and then
it will display the outside temperature. If you want to
see your current automatic fan speed, airflow direction
and temperature setting, press the AUTO button.In cold weather, the system will delay turning on the fan,
to avoid blowing cold air. During this delay the system
will be in FRONT defrost mode and the light in the button
will come on and stay on as long as the display is showing
the current mode, set TEMP and FAN speed. This light
will go off when the display returns to the outside
temperature. The length of the delay depends on the
engine coolant temperature and the outside temperature.
Pushing the FAN, AIR FLOW or FRONT buttons will
override this delay, turn off the AUTO setting and return
the system to manual operation.
Personal Choice Comfort Controls
(If Equipped)
This feature enables up to two drivers to store and recall
comfort control settings for the temperature, fan speed
and the direction of the airflow.
The memory buttons (1 or 2) for this feature are located
on the driver's door panel and correspond to the
numbers (1 or 2) found on the back of each keyless
entry transmitter.
To recall comfort settings, press the unlock button on the
remote keyless entry transmitter and put the ignition in
ACCESSORY or RUN. The climate control setting last
chosen by the identified driver (1 or 2) will be recalled.

3-8
To program a personal choice climate control setting,
do the following:
1. Choose a temperature setting for the driver and if
desired, for the passenger. See ªDual Automatic
ComforTemp

Climate Controlº and ªPassenger
Climate Controlº earlier in this section.
2. Adjust the fan speed and the direction of the airflow.
3. Locate the memory buttons on the driver's
door panel.
4. Press a memory button (1 or 2) until you hear two
beeps. The beeps confirm that your selection has
been saved and can now be recalled.
Follow these steps each time you want to change the
stored settings. For more information on the memory
feature, see ªMemory Seat and Mirrorsº in the Index.
Air Conditioning
On hot days, open the windows long enough to let hot
inside air escape. This reduces the time it takes for your
vehicle to cool down. Then keep your windows closed
for the air conditioner to work its best.
If you have the electronic touch system, for quick
cool
-down on very hot days, use maximum air
conditioning with the temperature and fan speed
adjusted to COOL and HIGH. If this setting is used
for long periods of time, the air in your vehicle may
become too cold and dry.
For normal cooling on hot days, use Normal and
adjust the temperature and fan speed for your comfort.
If Recirculation is selected while in the Normal air
conditioning mode, the system works like maximum
air conditioning and recirculates the air.

3-15
Setting the Tone (Bass/Treble)
AUDIO: Push and release AUDIO until BASS appears
on the display. Then turn the AUDIO knob clockwise to
increase bass. BASS and a positive number will appear
on the display. Turn the AUDIO knob counterclockwise
to decrease bass. BASS and a negative number will
appear on the display. BASS and a zero will appear on
the display when the bass level is set to the middle
position. Stop turning the knob when you find the bass
level you want or when the maximum or minimum level
is reached.
Push and release AUDIO until MID appears on the
display. Then turn the AUDIO knob clockwise to
increase treble. MID and a positive number will appear
on the display. Turn the AUDIO knob counterclockwise
to decrease treble. MID and a negative number will
appear on the display. MID and a zero will appear on the
display when the treble level is set to the middle
position. Stop turning the knob when you find the treble
level you want or when the maximum or minimum level
is reached.Push and release AUDIO until TREBLE appears on the
display. Then turn the AUDIO knob clockwise to
increase treble. TREBLE and a positive number will
appear on the display. Turn the AUDIO knob
counterclockwise to decrease treble. TREBLE and a
negative number will appear on the display. TREBLE
and a zero will appear on the display when the treble
level is set to the middle position. Stop turning the knob
when you find the treble level you want or when the
maximum or minimum level is reached. If a station is
weak or noisy, you may want to decrease the treble.
To adjust bass, midrange or treble to the middle
position, select BASS, MID or TREBLE. Then push and
hold AUDIO for more than two seconds until you hear a
beep. BASS and a zero, MID and a zero or TREBLE
and a zero will appear on the display. To adjust both
tone controls and both speaker controls to the middle
position, end out of audio mode by pushing the AUDIO
knob until the display goes blank. Then push and hold
AUDIO for more than two seconds until you hear a
beep. ALL CENTERED will appear on the display.

3-16
Adjusting the Speakers (Balance/Fade)
AUDIO: To adjust the balance between the right and
left speakers, push and release AUDIO until BAL
appears on the display. Then turn the AUDIO knob
clockwise to move the sound to the right speakers or
counterclockwise to move the sound to the left speakers.
A bar graph with indicators will show how the sound is
balanced between the right and left speakers. Stop
turning the AUDIO knob when you find the speaker
balance you want or when the maximum or minimum
level is reached.
To adjust the fade between the front and rear speakers,
push and release AUDIO until FADE appears on the
display. Then turn the AUDIO knob clockwise to move
the sound to the front speakers or counterclockwise to
move the sound to the rear speakers. A bar graph with
indicators will show how the sound is balanced between
the front and rear speakers. Stop turning the AUDIO
knob when you find the speaker balance you want or
when the maximum or minimum level is reached.To adjust balance or fade to the middle position, select
BAL or FADE. Then push and hold AUDIO for more
than two seconds until you hear a beep. The indicator
will be centered on the display To adjust both tone
controls and both speaker controls to the middle
position, end out of audio mode by pushing the AUDIO
knob until the display goes blank. Then press and hold
AUDIO for more than two seconds until you hear a
beep. ALL CENTERED will appear on the display.
Playing a Cassette Tape
The longer side with the tape visible should face to the
right. If the ignition and the radio are on, the tape can be
inserted and will begin playing. If you hear nothing or
hear a garbled sound, the tape may not be in squarely.
Press the eject button to remove the tape and start over.
While the tape is playing, use the volume, SEEK and
AUDIO controls just as you do for the radio. Other
controls may have different functions when a tape is
inserted. The display will show an arrow to show which
side of the tape is playing.