Program Key Fob BUICK LESABRE 2004 Get To Know Guide

Turn Signal/Multifunction Lever
Windshield Wiper Controls
MIST
Turn the WIPER band toward you and
release it for a single wipe cycle. For
more cycles, hold the band on MIST
longer.
WASH
Push the washer PUSH tab to spray
washer solvent on the windshield.
Moisture-Sensing Delay Windshield
Wipers (optional)
The moisture-sensing wiper system
monitors the moisture on the windshield The headlamps, parking and backup
lamps will illuminate when you press the
unlock symbol on the keyfob
transmitter.
See Section 3 of your Owner Manual.
Getting to Know Your2004 LeSabre10
Lamp Controls
Interior Lamps
See Section 3 of your Owner Manual for
interior lamp operating instructions.
Daytime Running Lamps
The Daytime Running Lamps will come
on when the ignition is ON, the head-
lamp switch is OFF, and the transaxle is
not in PARK (P).
Twilight Sentinel
This feature automatically switches the
headlamps on and off by sensing how
dark it is outside. You should not have to
manually turn the headlamps on or off.
The Twilight Sentinel control lever is
located to the left of the steering
column. To operate it, slide the lever
from OFF to MAX to adjust the
headlamps ON time from a few seconds
to 3 minutes, after the ignition has been
turned OFF.
Perimeter Lighting
Notice:Driver #1 and Driver #2 key
fob settings are unique. Refer to DIC
Programming.
15778 LeSABRE GUIDE 5/22/03 1:55 PM Page 10

Getting to Know Your2004 LeSabre16
New Key
If a new ignition key is required, it
should be purchased at a Buick dealer-
ship. The key is matched to your vehi-
cle’s module. The module will then learn
the new transponder key code.
See Section 2 of your Owner Manual.
Driver Memory Seat & Mirrors
(optional)
With the vehicle in PARK (P), adjust the
driver’s seat, including the lumbar posi-
tion (optional) and both outside mirrors
to a comfortable position. This feature
also recalls the radio and climate control
settings. However, it does not include
the power head restraint settings.
•Press and hold the appropriate
Driver/MEMORY button (located on
the driver’s door panel), to corre-
spond with the DIC Driver number,
until you hear two beeps.
•Follow the previous step with the
other key fob/transmitter to set up for
a second driver, and select the other
Driver/MEMORY button.
•Press and release the EXIT button.
With the transaxle in PARK (P), the
seat will move all the way back or to
your personalized exit position.
To recall the memory seat and mirrors
using the key fob/transmitter, program
the DIC Seat Recall feature to ON.
See Section 2 of your Owner Manual.
Driver Information Center (DIC)
(optional)
The DIC displays information about how
your vehicle is functioning and shows
warnings and messages if a system
problem is detected.
StabiliTrak
®Message
When the “STABILITY SYS ACTIVE”
message appears, a computer-
controlled system is automatically
activated. Some brake pedal noise or
vibration is normal. (StabiliTrak is an
optional feature.)
DIC Button Descriptions
•Press the ODO/TRIP button to dis-
play the vehicle’s total mileage, and
Trip 1 or Trip 2 miles. Press the
ODO/TRIP button for the appropriate
trip number, then press the RESET
button to reset the trip odometer.
•Press the FUEL INFO button to dis-
play fuel economy, fuel average, fuel
instantaneous, fuel range and fuel
used. Press the ODO/TRIP button for
the appropriate trip number, then
press the RESET button while the
15778 LeSABRE GUIDE 5/22/03 1:55 PM Page 16

To program and recall your personal
choice features:
Turn the ignition ON and place vehicle in
PARK (P).
1. To inform the DIC which driver you
are, press the appropriate memory
seat control button, or press the
unlock symbol on your key fob/
transmitter.
2. Press and hold ENG/METfor 5 sec-
onds. “Welcome to Buick Options
Feature” will appear on the DIC dis-
play. The next display will be your
driver number. Press ENG/METto
select the feature you want to program.
Follow the display information for each
feature. Press RESET to save the selec-
tion and advance to the next button.
When finished programming, “Options
Feature Selection Done” will appear on
the DIC display.
To exit without programming each
personal choice feature:
Press another DIC button or turn the
ignition to OFF. Your selections will be
retained.
17
average fuel economy is displayed in
the DIC to learn what the average
fuel economy is from a new starting
point.
•Press the GAGE INFO button to dis-
play oil pressure, coolant tempera-
ture, battery state, oil life index and
tire pressure information.
•Press the RESET button, along with
other buttons, to reset system
functions.
After an oil change:
•Press and hold the RESET button
while the oil life index is displayed in
the DIC. After 5 seconds, the oil life
will change to 100%.
•Press the ENG/MET button to change
the display to either English or metric
units.
See Section 3 of your Owner Manual.
DIC Programming
DIC Personal Choice Programming
The DIC can be used to program the fol-
lowing features for two drivers:
•Outside Curb View Assist Mirror
•Automatic Door Locks
•Delayed Locking
•Security Feedback
•Perimeter Lighting
•Memory Seats
•Window Lockout
•Driver ID
•Language Selection
The DIC recognizes the drivers as
Driver #1 and Driver #2 (Memory 1 and
Memory 2).
Each key fob/transmitter is unique and
marked with either a #1 or #2 on the
back.
15778 LeSABRE GUIDE 5/22/03 1:55 PM Page 17

19
Perimeter Lighting
To turn the headlamps, parking lamps
and backup lamps on when you press
on the key fob/transmitter:
1.PERIMETER LIGHTS (OFF/ON)
Press ENG/METto select OFF or
ON.
If you select OFF for PERIMETER
LIGHTS, there will be no perimeter
lighting.
If you select ON for PERIMETER
LIGHTS, the lights will illuminate.
Press RESETto record your choice.
Memory Seats Recall
To recall the position of your seat and
mirrors when you press unlock on the
key fob/transmitter:
1.SEAT RECALL (OFF/ON)Press
ENG/METto select OFF or ON.
If you select OFF for SEAT RECALL,
there will be no seat recall feature.
If you select ON for SEAT RECALL,
the seat and mirrors will move to their
preset memory positions when the
vehicle is unlocked using the key
fob/transmitter.
Press RESETto record your choice.
2.RECALL POSITION MEMORY
(EXIT)Press ENG/METto select
MEMORY or EXIT.
If you select MEMORY for RECALL
POSITION, the seat and mirrors will
move to their preset memory
positions.
Note:If you desire perimeter lighting,
you must select LIGHTS for UNLOCK
FEEDBACK.If you select EXIT for RECALL POSI-
TION, the seat and mirrors will move
to their preset exit positions.
Press RESETto record your choice.
Window Lockout
To select the number of passenger win-
dows you want to prevent from being
opened:
1.WINDOW LOCK (R+ PASS/REAR)
Press ENG/MET to select R+ PASS
or REAR.
If you select R+ PASS for WINDOW
LOCK, all three passenger windows
will lock out.
If you select REAR, the two rear win-
dows will lock out.
Press RESETto record your choice.
See your Owner Manual for Driver ID and
Language Selection programming.
Note:This feature is activated by press-
ing the WINDOW LOCK switch on the
driver’s door.
15778 LeSABRE GUIDE 5/22/03 1:55 PM Page 19