ignition BUICK LESABRE 2005 Get To Know Guide

9
Window Controls
The power window controls are located
on the driver’s door armrest.
ExpressDown Window
AUTO:
Press this switch rearward and
release to express open the window.Press the switch again to stop a windowin express.
Window Lockout
LOCK:
Press this switch to disable the
passenger window switches. The switch
will illuminate to indicate the lock isactive.
Press the switch again to enable the
passenger window switches.
Window Lockout is a programmable fea
ture. Refer to the DIC Programming section in this guide for further information.
See Section 2 of your Owner Manual.
Sunroof (if equipped)
The ignition must be in the ON position
or the Retained Accessory Power (RAP)must be active to operate the sunroof.
The sunroof switch is located on the
headliner, between the sun visors.
Press and hold the switch rearward and
release to express open the glass paneland sunshade. The sunroof will open
automatically to the fullopen position.
Press the switch again at the desired
point to stop the panel in a partially openposition.
Press and hold the switch forward to
close the glass panel. The sunshademust be manually closed.
Vent
The vent position raises the rear portion
of the sunroof. Once it is closed, the
sunroof can be opened to a vent position. (The sunshade must be openedand closed manually for vent operation.)
Push the sunroof switch upward to vent.Pull the sunroof switch downward to
close.
See Section 2 of your Owner Manual.

Turn Signal/Multifunction Lever
Windshield Wiper Controls
MIST
Turn the WIPER band toward you and
release it for a single wipe cycle. Formore cycles, hold the band on MIST
longer.
WASH
Push the washer PUSH tab to spray
washer solvent on the windshield. The headlamps, parking and backup
lamps will illuminate when you press theunlock symbol ( ) on the keyfob
transmitter.
See Section 3 of your Owner Manual.
Getting to Know YourLeSabre10
Lamp Controls
Interior Lamps
See Section 3 of your Owner Manual for
interior lamp operating instructions.
Daytime Running Lamps
The Daytime Running Lamps will come
on when the ignition is on, the headlamp
switch is OFF, and the transaxle is not inPark (P).
Twilight Sentinel
This feature automatically switches the
headlamps on and off by sensing how
dark it is outside. You should not have to
manually turn the headlamps on or off.
The Twilight Sentinel control lever is
located to the left of the steering
column. To operate it, slide the leverfrom OFF to MAX to adjust the headlamps ON time from a few secondsto three minutes, after the ignition has
been turned OFF.
Perimeter Lighting
Notice:
Driver #1 and Driver #2 key
fob settings are unique. Refer to DICProgramming.

Getting to Know YourLeSabre12
Trunk ReleaseValet Key (if equipped)
The remote TRUNK RELEASE button is
located on the driver’s door.
Remote Trunk Release
Vehicle must be in Park (P) or Neutral
(N) and the trunk release lockoutunlocked.
Press the TRUNK RELEASE button to
open the trunk lid.
Remote Trunk Release Lockout
This feature allows you to secure items
in the trunk by disabling the TRUNKRELEASE button.
Insert the ignition key into the TRUNK
RELEASE button. Turn the key onequarter of a turn to the right. Remove
the key.
See Section 2 of your Owner Manual.
The Valet Key is used for the ignition
and side doors only. It does not openthe trunk or glove box. Use this keywhen valet parking your vehicle. Use theignition key to open all doors, the trunk,
and glove box. Do not use a Valet Key
to duplicate an ignition key.
See Sections 2 and 5 of your Owner Manual.

15
Press the image height adjuster control’s
up or down arrow to raise or lower the
HUD image on the windshield to suityour personal preference.
See Section 3 of your Owner Manual.
Universal Transmitter
(if equipped)
Programmable Universal Transmitter
You can program up to three transmit
ters. The vehicle’s engine should be
turned off during programming.
To erase any previous settings
Press and hold the two outside buttons
simultaneously until the indicator light
flashes rapidly. Release the buttons.Hold your handheld transmitter against
the bottom surface of the Universal
Transmitter (UT) so you can see theindicator light.
Choose one of the three buttons to
program. Press and hold the transmitter
button and the UT button until the indicator light flashes rapidly (this couldtake up to 90 seconds). Release bothbuttons.
Operate Universal Transmitter
Press and hold the appropriate button.
The light will illuminate while the signalis being transmitted.
PASSKey®III
The PASSKey®III is a passive theft
deterrent system that provides your
vehicle with a higher level of security by
offering 3 trillion electronic securitycodes.
A single key opens all locks and oper
ates the ignition. A transponder is locat
ed in the key. With the key in the igni
tion, the transponder is activated and
emits an encoded signal. This signalallows the engine to start.
Note:Make sure people and objects
are clear of the garage door you areprogramming.
New Key
If a new ignition key is required, it
should be purchased at a Buick dealer
ship. The key is matched to your vehi
cle’s module. The module will then learnthe new transponder key code.
See Section 2 of your Owner Manual.

To program and recall your personal
choice features
Turn the ignition on and place vehicle in
Park (P).
1. To inform the DIC which driver you
are, press the appropriate memoryseat control button, or press theunlock symbol on your key fob/
transmitter.
2.Press and hold ENG/MET for five
seconds. “Welcome to Buick Options
Feature” will appear on the DIC dis
play. The next display will be your
driver number. Press ENG/MET to
select the feature you want to program.
Follow the display information for each
feature. Press RESET to save the selection and advance to the next feature.
When finished programming, “Options
Feature Selection Done” will appear on
the DIC display.
To exit without programming each
personal choice feature
Press another DIC button or turn the
ignition to off. Your selections will beretained.
17
• Press the GAGE INFO button to dis
play oil pressure, coolant temperature, battery state, oil life index andtire pressure information.
• Press the RESET button, along with
other buttons, to reset system functions.
After an oil change
• Press and hold the RESET button
while the oil life index is displayed in
the DIC. After 5 seconds, the oil life will change to 100%.
•Press the ENG/MET button to change
the display to either English or metric
units.
See Section 3 of your Owner Manual.
DIC Programming
DIC Personal Choice Programming
The DIC can be used to program the fol
lowing features for two drivers:
• Outside Curb View Assist Mirror
• Automatic Door Locks
• Delayed Locking
• Security Feedback
• Perimeter Lighting
• Memory Seats
• Window Lockout
• Driver ID
• Language Selection
The DIC recognizes the drivers as
Driver #1 and Driver #2
(Memory 1 and
Memory 2).
Each key fob/transmitter is unique and
marked with either a #1 or #2 on theback.