lock BUICK TERRAZA 2007 Service Manual

If your vehicle has power sliding door(s), you can
prevent power opening of the sliding door from
the passenger power sliding door (psd) activation
switch by pressing the psd second row passenger
override (deactivation) switch located on the
overhead console. SeePower Sliding Door (PSD)
on page 112.
If you want to open the sliding door while the
security lock is on, unlock and open the door from
the outside.
You should let adults and older children know how
the security lock works, and how to cancel the lock.
If you do not, adults or older children who ride in the
rear will not be able to open the sliding door from
the inside while the security lock feature is in use.
Canceling the Sliding Door
Security Lock
1. Unlock the sliding door and open the door
from the outside.
2. Push the security lock lever all the way down.
3. Close the door.
4. Repeat Steps 1 through 3 for the other door.
The sliding door lock will now work normally.
Power Sliding Door (PSD)
If your vehicle has this feature, you can open and
close the power sliding door(s) using the
switches inside your vehicle. You can also operate
the sliding door(s) with your remote keyless
entry transmitter. SeeRemote Keyless Entry
System on page 98.
{CAUTION:
Leaving your children or pets unattended
in your vehicle can be dangerous. They
could operate the power sliding door. A
child or others could be injured. Do not
leave children or pets unattended in your
vehicle.
112

Press the power sliding door button on the
remote keyless entry transmitter.
To manually open the power sliding door(s)
while the switch(es) are in the activation
position, pull and release the inside or outside
door handle to release the door latch. The
door will fully open.
To manually close the power sliding door(s)
while the switches are in the activation
position, pull the inside or outside door handle
or the edge of the door. Move the door
about 4 inches (10 cm) toward the closed
position and release it. The door will close
completely and latch.
If a power sliding door is locked, it cannot be
unlocked and opened using the overhead console
PSD switch(es) or the passenger PSD activation
switch(es). The power sliding door must either be
manually unlocked or unlocked using the power
door unlock switch located on the driver’s or front
passenger’s armrest, and then opened using the
overhead or passenger PSD activation switch(es).The remote keyless entry transmitter can also be
used to open the power sliding door(s). If the
vehicle is locked, press the power sliding
door button(s) and all doors will unlock and the
sliding door(s) will open. SeeRemote Keyless
Entry System Operation on page 99.
If the power sliding door has been manually locked,
you must unlock the PSD before it can be opened.
Notice:If you leave the power sliding door on
when you go through an automatic car
wash, the door may accidentally open. Be sure
the power sliding door is turned off when
going through a car wash.
115

Power Sliding Door Second Row
Passenger Override (Deactivation)
To help avoid accidental operation of the sliding
door(s) by using the passenger PSD activation
switch, press the override (deactivation) part of the
overhead console switch. The door can still be
manually opened from the inside or outside
with the override (deactivation) on.
To open a power sliding door(s) manually when
the overhead console switch is in override
(deactivation) position, pull the inside or outside
door handle and slide the door all the way back.
To close the door(s) manually when the override
switch(es) is in the override (deactivation) position,
pull the inside or outside door handle and slide
the door all the way forward to the latched position.
To stop the door(s) immediately while the
door(s) is opening or closing, press the PSD
override (deactivation) part of the switch.
Pressing the PSD button(s) on the remote keyless
entry will open and close the door unless the
door has been manually locked using the
mechanical slider.
Resetting the Power Sliding Door
The power sliding door may operate incorrectly or
not at all because of the following conditions:
A low voltage or dead battery
A disconnected battery
If the instrument panel PSD/fuse 21,
LHPSD/fuse 24 or RHPSD/fuse 25 are
removed or blown.
SeeFuses and Circuit Breakers on page 497for
more information.
If any of these conditions occur, the power sliding
door may need to be reset. If your vehicle has
the dual power sliding doors, both doors will have
to be reset. To reset a door, do the following:
1. Check to be sure the power sliding door is
unlocked and securely closed.
2. Turn the ignition to LOCK.
118

3. If the power sliding door overhead console
switch is in the override (deactivation)
position, return to the activation position.
4. Open the sliding door using the remote
keyless entry transmitter, overhead console
switch, or passenger switch. Allow the door to
travel fully open.
If the door does not travel to the fully open
position, press the overhead console switch to the
override (deactivation) position and slide the
door fully open and closed. Check for foreign
objects in the tracks. Repeat the procedure starting
with Step 1. If the door resists travel to the fully
open position, see your dealer for service.Liftgate
To unlock or lock the liftgate from the outside, use
the remote keyless entry transmitter. For more
information, seeRemote Keyless Entry System
Operation on page 99.
You can also use the power door lock switch to
lock and unlock the liftgate.
Open the liftgate using the handle located above
the license plate. Once slightly opened, the
liftgate will rise by itself. Lamps in the rear of the
vehicle will come on, illuminating the rear
cargo area.
Notice:If you open the liftgate without
checking for overhead obstructions such as a
garage door, you could break the liftgate
glass. Always check to make sure the area
above the liftgate is clear before opening it.
119

Power Rear Quarter Windows
Your vehicle has power rear quarter windows.
This switch, located in
the overhead console
switchbank, is used
for opening and closing
the power rear
quarter windows.
Press the top of the switch to open the windows;
both windows will open. The windows will
continue to open as long as the switch is pressed,
until they are fully opened.
Press the bottom of the switch with the symbol to
close both windows. The windows can be
closed fully or partially, depending on how long
the switch is pressed.The ignition must be in RUN, ACCESSORY, or
Retained Accessory Power (RAP) must be active,
to use the power rear quarter windows. See
Retained Accessory Power (RAP) on page 130.
Sun Visors
To block out glare, you can swing down the visors
and slide them along the rod to cover different
areas of the front window. You can also remove
them from the center mount and swing them to
the side.
Lighted Vanity Mirror
Your vehicle has lighted vanity mirrors. Pull down
the sun visor and ip up the cover to expose
the vanity mirror. The lamps will come on when
you ip up the cover.
Theft-Deterrent Systems
Vehicle theft is big business, especially in some
cities. Although your vehicle has a number of
theft-deterrent features, we know that nothing we
put on it can make it impossible to steal.
123

Content Theft-Deterrent
Your vehicle has a theft-deterrent alarm system.
A light located on top of your instrument panel,
near the center of the vehicle next to the
windshield, will ash slowly to let you know that
the system has been armed.
While armed, the doors will not unlock with the
power door lock switch.Once armed, the alarm will go off if someone tries
to enter the vehicle without using the remote
keyless entry transmitter or a key, or turns
the ignition to RUN. The horn will sound and the
turn signal lamps will ash for up to two minutes.
Arming with the Power Lock Switch
Your alarm system will arm when the key is
removed from the ignition and you use the driver’s
power door lock switch, with the driver’s door
open or the passenger’s door power door
lock switch with the passenger’s door open to lock
the vehicle. If you would like to turn on power
door lock switch arming, seeDIC Vehicle
Personalization (Uplevel Only) on page 249
When the security light ashes quickly the system
is arming. After all doors and the liftgate are
closed and locked, the security light will begin
ashing at a very slow rate to let you know
the system is armed.
124

Arming with the Remote Keyless Entry
Transmitter
Your alarm system will arm if the key is not in the
ignition and you use your remote keyless entry
transmitter to lock the doors. The security light will
ash to let you know the system is arming. If
you press the transmitter’s lock button twice within
5 seconds, the horn will sound. After all doors
and the liftgate are closed and locked, the security
light will begin ashing at a very slow rate to let
you know the system is armed.
Arming with Your Key
Your alarm system will arm when you use your
key to lock the driver’s door. The security light will
ash to let you know the system is arming.
After all doors and the liftgate are closed and
locked, the security light will begin ashing at a
very slow rate to let you know the system is
armed. If you would like your key not to arm the
system, seeDIC Vehicle Personalization (Uplevel
Only) on page 249.
Arming Conrmation
If remote unlock conrmation is on, the turn signal
lamps will ash briey to let you know when
your alarm system has disarmed. If you would not
like the turn signal lamps to ash, seeDIC
Vehicle Personalization (Uplevel Only) on
page 249.
Disarming with the Remote Keyless
Entry Transmitter
Your alarm system will disarm when you use your
remote keyless entry transmitter to unlock the
doors. The security light will stop ashing to let you
know the system is no longer armed.
Disarming with Your Key
Your alarm system will disarm when you use your
key to unlock the driver’s door. The security
light will stop ashing to let you know the system
is no longer armed. If you would like your key
not to disarm the alarm system, seeDIC Vehicle
Personalization (Uplevel Only) on page 249.
125

The starter will not work and fuel will stop being
delivered to the engine. Anyone using a
trial-and-error method to start the vehicle will be
discouraged because of the high number of
electrical key codes.
If the engine does not start and the security
message comes on, the key may have a damaged
transponder. Turn the ignition off and try again.
If the engine still does not start, and the key
appears to be undamaged, try another ignition key.
At this time, you may also want to check the
instrument panel PASS KEY fuse. If the engine still
does not start with the other key, your vehicle
needs service. If your vehicle does start, the rst
key may be faulty. See your dealer or a locksmith
who can service the PASS-Key
®III to have a new
key made. SeeFuses and Circuit Breakers on
page 497.
It is possible for the PASS-Key
®III decoder to learn
the transponder value of a new or replacement key.
Up to 10 keys may be programmed for the vehicle.
This procedure is for learning additional keys only.
If all the currently programmed keys are lost or do
not operate, you must see your dealer or a
locksmith who can service PASS-Key
®III to have
keys made and programmed to the system.See your dealer or a locksmith who can service
PASS-Key
®III to get a new key blank that is
cut exactly as the ignition key that operates the
system.
To program the new key, do the following:
1. Verify the new key has PK3 stamped on it.
2. Insert the original, already programmed
key into the ignition lock cylinder and start the
engine. If the engine will not start, see your
dealer for service.
3. After the engine has started, turn the key to
LOCK and remove the key.
4. Insert the key to be programmed and turn it to
RUN within 10 seconds of removing the
previous key.
5. The security message will turn off once the
key has been programmed. It may not be
apparent that the security message went on
due to how quickly the key is programmed.
6. Repeat Steps 1 through 4 if additional keys
are to be programmed.
127

If you are ever driving and the security message
comes on and stays on, you will be able to restart
your engine if you turn it off. Your PASS-Key
®III
system, however, is not working properly and must
be serviced by your dealer. Your vehicle is not
protected by the PASS-Key
®III system at
this time.
If you lose or damage a PASS-Key
®III key, see
your dealer or a locksmith who can service
PASS-Key
®III to have a new key made.
Starting and Operating Your
Vehicle
New Vehicle Break-In
Notice:Your vehicle does not need an
elaborate break-in. But it will perform better in
the long run if you follow these guidelines:
Do not drive at any one constant speed,
fast or slow, for the rst 500 miles
(805 km). Do not make full-throttle starts.
Avoid downshifting to brake, or slow,
the vehicle.
Avoid making hard stops for the rst
200 miles (322 km) or so. During this time
your new brake linings are not yet broken
in. Hard stops with new linings can mean
premature wear and earlier replacement.
Follow this breaking-in guideline every time
you get new brake linings.
Do not tow a trailer during break-in. See
Towing a Trailer on page 386for the trailer
towing capabilities of your vehicle and more
information.
Following break-in, engine speed and load can
be gradually increased.
128

Ignition Positions
The key can be turned to one of four positions
while in the ignition switch.
A (LOCK):This is the only position from which
you can remove the key. This position locks
your ignition and transaxle.Notice:Using a tool to force the key from the
ignition switch could cause damage or
break the key. Use the correct key and turn the
key only with your hand. Make sure the key
is all the way in. If none of this works,
then your vehicle needs service.
B (ACCESSORY):This is the position in which
you can operate the electrical accessories, such as
the radio.
C (RUN):This is the position to which the switch
returns after the engine is started and the ignition
key is released. This is the position for driving. Even
while the engine is not running, RUN can be used to
operate your electrical accessories and to display
some instrument panel warning lights.
The battery could be drained if you leave the key in
the ACCESSORY or RUN position with the engine
off. You may not be able to start your vehicle if the
battery is allowed to drain for an extended period
of time.
D (START):This position starts the engine. When
the engine starts, release the ignition key. The
switch will return to RUN for driving.
129