display CADILLAC CTS 2003 1.G Manual PDF

3-28 Audio Steering Wheel Controls
Some audio controls can be adjusted at the steering
wheel. They include the following:
Volume: Turning the
knob increases and
decreases volume.
(Band/Source): Press this button to select AM,
FM1, FM2 or a source, either radio, cassette tape or CD.
The cassette or CD must be loaded to play. Available
loaded sources are shown on the display as a tape or a
CD symbol. (For vehicles with the six
-disc changer
radio
- If none of the audio sources are loaded, and this
button is pressed, NO SOURCE LOADED will appear
on the display.)
(Mute): Press this button to silence the system.
Press it again to turn on the sound. If your vehicle has
the Navigation system, this button does not have a
mute function.
See ªReconfigurable
Steering Wheel Controls
(SWC)º in the Index for
more information on
this feature.

3-31 Care of Your Cassette Tape Player
A tape player that is not cleaned regularly can cause
reduced sound quality, ruined cassettes or a damaged
mechanism. Cassette tapes should be stored in their
cases away from contaminants, direct sunlight and
extreme heat. If they aren't, they may not operate
properly or may cause failure of the tape player.
Your tape player should be cleaned regularly after every
50 hours of use. Your radio will display CLEAN TAPE
to indicate that you have used your tape player for
50 hours without resetting the tape clean timer. If this
message appears on the display, your cassette tape
player needs to be cleaned. It will still play tapes,
but you should clean it as soon as possible to prevent
damage to your tapes and player. If you notice a
reduction in sound quality, try a known good cassette to
see if the tape or the tape player is at fault. If this other
cassette has no improvement in sound quality, clean the
tape player.
For best results, use a scrubbing action, non
-abrasive
cleaning cassette with pads which scrub the tape head as
the hubs of the cleaner cassette turn. The recommended
cleaning cassette is available through your dealer
(GM Part No. 12344789).For vehicles with the single compact disc player, use the
following steps:
1. Turn the ignition to ON or ACCESSORY.
2. Turn the radio on.
3. Insert the scrubbing action cleaning cassette.
4. Eject the cleaning cassette after the manufacturer's
recommended cleaning time.
For vehicles with the six
-disc compact disc player, when
cleaning the cassette tape player with the recommended
non
-abrasive cleaning cassette, it is possible that the
cassette may eject, because the cut tape detection feature
on your radio may recognize it as a broken tape, in error.
To prevent the cleaning cassette from being ejected, use
the following steps:
1. Turn the ignition to ON or ACCESSORY.
2. Turn the radio on.
3. Insert the scrubbing action cleaning cassette.
4. Eject the cleaning cassette after the manufacturer's
recommended cleaning time.

3-32
You may also choose a non-scrubbing action, wet-type
cleaner which uses a cassette with a fabric belt to clean
the tape head. This type of cleaning cassette will not
eject on its own. A non
-scrubbing action cleaner may
not clean as thoroughly as the scrubbing type cleaner.
The use of a non
-scrubbing action, dry-type cleaning
cassette is not recommended.
After you clean the player, perform the following steps:
1. Press the TUNE/SEL knob.
2. Turn the TUNE/SEL knob until SETUP is displayed.
3. Press the TUNE/SEL knob to enter SETUP.
4. Turn the TUNE/SEL knob until CLEAR TAPE
HOURS is displayed.
5. Press the TUNE/SEL knob to select. The radio
will display CLEARED to show that the indicator
was reset.
Cassettes are subject to wear and the sound quality
may degrade over time. Always make sure the cassette
tape is in good condition before you have your tape
player serviced.
Care of Your Compact Discs
Handle discs carefully. Store them in their original cases
or other protective cases and away from direct sunlight
and dust. If the surface of a disc is soiled, dampen a
clean, soft cloth in a mild, neutral detergent solution and
clean it, wiping from the center to the edge.
Be sure never to touch the side without writing when
handling discs. Pick up discs by grasping the outer edges
or the edge of the hole and the outer edge.
Care of Your Compact Disc Player
The use of CD lens cleaner discs is not advised, due to
the risk of contaminating the lens of the CD optics with
lubricants internal to the CD mechanism.

4-10
To turn the system off, press
the TC (traction control)
button located in the
glove box.
If you press the TC button once, the traction control
system will turn off and the traction control system
warning light will come on. Press the TC button again
to turn the system back on. If you press and hold the
TC button for five seconds, the Stabilitrak system will
turn off. Press the TC button again to turn Stabilitrak
back on.
Stabilitrak
- Vehicle Stability
Enhancement System (If Equipped)
Your vehicle may be equipped with a vehicle stability
enhancement system called Stabilitrak. Stabilitrak is an
advanced computer controlled system that assists you
with directional control of the vehicle in difficult driving
conditions.Stabilitrak has sensors that detect the direction your
vehicle is going and compares it to the direction that you
are steering the vehicle. Stabilitrak activates when the
computer senses a discrepancy between your intended
path and the direction the vehicle is actually traveling.
To assist you in returning your vehicle to the intended
path, Stabilitrak selectively applies braking pressure at
any one of the vehicle's brakes to help steer the vehicle
in the direction which you are steering.
When the system activates, a STABILITY SYS
ENGAGED message will be displayed on the Driver
Information Center. See ªDriver Information Center
Messagesº in the Index. You may also hear a noise or feel
vibration in the brake pedal. This is normal. Continue to
steer the vehicle in the direction you want it to go.
If there is a problem detected with Stabilitrak, a
SERVICE STABILITY SYS message will be displayed
on the Driver Information Center. See ªDriver
Information Center Messagesº in the Index. When this
message is displayed, the system is not operational.
Driving should be adjusted accordingly.
Stability comes on automatically whenever you start
your vehicle. To help assist you with directional control
of the vehicle, you should always leave the system on.
You can turn Stabilitrak OFF if you ever need to trough
the Traction On/Off button. See ªTraction Control
Systemº in the Index.

5-9
To disconnect the jumper cables from both vehicles, do
the following:
1. Disconnect the black negative (
-) cable the vehicle
that had the dead battery.
2. Disconnect the black negative (
-) cable from the
vehicle with the good battery.
3. Disconnect the red positive (+) cable from the
vehicle with the good battery.
4. Disconnect the red positive (+) cable from the
other vehicle.
Towing Your Vehicle
Consult your dealer or a professional towing service if
you need to have your disabled vehicle towed. See
ªRoadside Assistanceº in the Index. If you want to tow
your vehicle behind another vehicle for recreational
purposes (such as behind a motorhome), see
ªRecreational Vehicle Towingº in the Index.
Engine Overheating
There are three engine hot messages that may be
displayed in the Driver Information Center (DIC).
See ªEngine Hot Warning Messagesº in the Index.

6-7
CAUTION:
If you get fuel on yourself and then something
ignites it, you could be badly burned. Fuel can
spray out on you if you open the fuel cap too
quickly. This spray can happen if your tank is
nearly full, and is more likely in hot weather.
Open the fuel cap slowly and wait for any ªhissº
noise to stop. Then unscrew the cap all the way.
Be careful not to spill fuel. Clean fuel from painted
surfaces as soon as possible. See ªCleaning the Outside
of Your Vehicleº in the Index.
When you put the fuel cap back on, turn it to the right
(clockwise) until you hear a clicking sound. Make sure
you fully install the cap. The diagnostic system can
determine if the fuel cap has been left off or improperly
installed. This would allow fuel to evaporate into the
atmosphere. See ªMalfunction Indicator Lampº in
the Index.The Check Gas Cap message will appear on the DIC
display if the fuel cap is not reinstalled properly. See
ªCheck Message, Gas Capº in the Index for more
information.
NOTICE:
If you need a new fuel cap, be sure to get the
right type. Your dealer can get one for you. If you
get the wrong type, it may not fit properly. This
may cause your malfunction indicator lamp to
light and may damage your fuel tank and
emissions system. See ªMalfunction Indicator
Lampº in the Index.

6-15
How to Reset the Change Engine Oil Message and
the Oil Life Indicator
The GM Oil Life System
calculates when to change
your engine oil and filter based on vehicle use. Anytime
your oil is changed, reset the system so it can calculate
when the next oil change is required. If a situation
occurs where you change your oil prior to a Change
Engine Oil message in the DIC being turned on, reset
the system.
After the oil has been changed, the Change Engine
Oil message and the oil life indicator must be reset.
To reset the message and indicator, use one of the
following procedures:Base Audio System
Press the CLR button located to the right of the DIC
display to acknowledge the CHANGE ENGINE OIL
message. This will clear the message from the display
and reset it.
To reset the oil life indicator, use the following steps:
1. Press the up or down arrow on the INFO button
located to the right of the DIC display to access the
DIC menu.
2. Once XXX% ENGINE OIL LIFE menu item is
highlighted, press and hold the CLR button.
The percentage will return to 100, and the oil life
indicator will be reset.
3. Repeat the steps if the percentage does not
return to 100.

6-16
Navigation System
Press the multi
-function button, next to the OK prompt
in the upper right of the display, to acknowledge the
Change Engine Oil message. This will clear the message
from the display and reset it.
To reset the oil life indicator, use the following steps:
1. Turn the system on by pressing the PWR/VOL knob
once. The PWR/VOL knob is located to the lower
left of the DIC display.
2. Press the INFO button located to the left
of the display to access the Vehicle Info
(Information) menu.
3. Turn the TUNE/SEL knob located to the lower right
of the display until Engine Oil Life is highlighted.
Press the knob once to select it.
4. Once XXX% Engine Oil Life is displayed, press the
multi
-function button next to the Reset prompt in the
upper right corner of the display.
The percentage will return to 100, and the oil life
indicator will be reset.
5. Repeat the steps if the percentage does not
return to 100.
What to Do with Used Oil
Used engine oil contains certain elements that may be
unhealthy for your skin and could even cause cancer.
Don't let used oil stay on your skin for very long. Clean
your skin and nails with soap and water, or a good hand
cleaner. Wash or properly throw away clothing or rags
containing used engine oil. See the manufacturer's
warnings about the use and disposal of oil products.
Used oil can be a threat to the environment. If you
change your own oil, be sure to drain all the oil from the
filter before disposal. Never dispose of oil by putting it
in the trash, pouring it on the ground, into sewers, or
into streams or bodies of water. Instead, recycle it by
taking it to a place that collects used oil. If you have
a problem properly disposing of your used oil, ask
your dealer, a service station or a local recycling center
for help.

6-22 How to Reset the Change Transmission
Fluid Message and the Transmission Fluid
Indicator (Automatic Transmission Only)
After the transmission fluid has been changed, the
Change Trans Fluid message and the transmission fluid
life indicator must be reset. To reset the message and
indicator, use one of the following procedures:
Base Audio System
Press the CLR button located to the right of the DIC
display to acknowledge the CHANGE TRANS FLUID
message. This will clear the message from the display
and reset it.
To reset the transmission fluid life indicator, use the
following steps:
1. Press the up or down arrow on the INFO button
located to the right of the DIC display to access the
DIC menu.
2. Once the XXX% TRANS FLUID LIFE menu item is
highlighted, press and hold the CLR button.
The percentage will return to 100, and the
transmission fluid life indicator will be reset.
3. Repeat the steps if the percentage does not
return to 100.Navigation System
Press the multi
-function button located to the right of
the DIC display, next to the OK prompt to acknowledge
the Change Trans Fluid message. This will clear the
message from the display and reset it.
To reset the transmission fluid life indicator, use the
following steps:
1. Turn the system on by pressing the PWR/VOL knob
once. The PWR/VOL knob is located to the lower
left of the DIC display.
2. Press the INFO button located to the left of
the DIC display to access the Vehicle Info
(Information) menu.
3. Turn the TUNE/SEL knob located to the lower right
of the DIC display until Trans Fluid Life is
highlighted. Press the knob once to select it.
4. Once XXX% Trans Fluid Life is displayed, press the
multi
-function button next to the Reset prompt in the
upper right corner of the display.
The percentage will return to 100, and the
transmission fluid life indicator will be reset.
5. Repeat the steps if the percentage does not
return to 100.

6-31
Brakes
Brake Fluid
Your brake master cylinder reservoir is on the driver's side
of the engine compartment. It is filled with DOT
-3 brake
fluid. See ªEngine Compartment Overviewº in the Index.
There are only two reasons why the brake fluid level in the
reservoir might go down. The first is that the brake fluid
goes down to an acceptable level during normal brake
lining wear. When new linings are put in, the fluid level
goes back up. The other reason is that fluid is leaking out
of the brake system. If it is, you should have your brakesystem fixed, since a leak means that sooner or later your
brakes won't work well, or won't work at all.
So, it isn't a good idea to ªtop offº your brake fluid.
Adding brake fluid won't correct a leak. If you add fluid
when your linings are worn, then you'll have too much
fluid when you get new brake linings. You should add
(or remove) brake fluid, as necessary, only when work is
done on the brake hydraulic system.
CAUTION:
If you have too much brake fluid, it can spill on the
engine. The fluid will burn if the engine is hot
enough. You or others could be burned, and your
vehicle could be damaged. Add brake fluid only
when work is done on the brake hydraulic system.
If the ignition is in ON and the brake fluid is low, the
Check Brake Fluid message will be displayed in the
DIC. See ªCheck Message, Brake Fluidº in the Index
for more information.
When your brake fluid falls to a low level, your brake
warning light will come on. See ªBrake System Warning
Lightº in the Index.