display CADILLAC CTS 2003 1.G Owners Manual

1-5 Heated Front Seats (If Equipped)
If your vehicle is equipped
with heated front seats, the
buttons are located on the
climate control panel.There is a button for the driver and one for the front
passenger. Each button has the following three settings:
LO, HI and off. The active setting appears on the
climate control panel display. The LO setting warms the
seatback and cushion until the seat approximates normal
body temperature. The HI setting has a slightly higher
temperature.
To turn on the heated seats, press the button once. The
seat will heat to the HI setting. Press the button again to
switch to the LO setting. Pressing the button a third time
turns the system off.
The heated seats can only be used when the ignition is
turned on. When the vehicle is turned off, the heated
seats automatically turn off. If you wish to have the
heated seats on once the vehicle is restarted, press the
button again.

2-9
Automatic Door Locks
If your vehicle has an automatic transmission, your
vehicle is programmed so that when the doors are
closed, the ignition is on and the shift lever is moved out
of PARK (P), all the doors will lock. The doors will
unlock every time you stop the vehicle and move the
shift lever back into PARK (P).
If your vehicle has a manual transmission, the doors
will lock automatically after the vehicle speed reaches
5 mph (8 km). The doors will not automatically unlock
until the ignition is turned off and the key is removed
from the ignition switch.
If someone needs to exit the vehicle once the doors have
locked, have that person use the manual lever or power
door lock switch. When the door is closed again, it will
not lock automatically. Use the manual lever or power
lock switch to lock the door.
Programmable Automatic Door Locks
The power door locks can be programmed through
prompts displayed on the Driver Information Center
(DIC). These prompts allow you to choose various
lock and unlock settings. For more information on
programming, see ªVehicle Programming and
Personalization Featuresº in the Index.
Rear-Door Security Locks
Your vehicle is equipped with rear door security locks
that prevent passengers from opening the rear doors on
your vehicle from the inside.
The rear door security locks
are located on the inside
edge of each rear door. You
must open the rear doors to
access them.
To use these locks, do the following:
1. Insert your key into the slot next to the rear door
security lock label and turn it to engage the lock.
2. Close the door.
3. Repeat the steps for the other rear door.
The rear doors on your vehicle cannot be opened from
the inside when this feature is in use.

2-15
2. Scroll through the menu by turning the knob.
3. When SETUP appears on the display, press the knob
once to select it.
4. Scroll through the SETUP menu by turning
the knob.
5. When CONFIGURE SWC KEYS appears on the
display, press the knob once to select it.
6. Scroll through the buttons (1, 2, 3 or 4). When you
reach the control you wish to program, press the
knob once to select it.
7. Choose a new function for the control by scrolling
through the list of available functions.
8. Once you've highlighted your choice, press the knob
once to select it.
The control you selected is now programmed with
the function you selected.
9. Press the BACK button to exit each menu.
If you desire to program another control, repeat
the procedure.
If your vehicle is equipped with the Navigation system,
do the following:
1. Press the MAIN button located to the lower left of
the display.2. Press the multi-function button next to the Setup
prompt at the right of the display.
3. Turn the TUNE/SEL knob located to the lower right
of the display to scroll through the Setup menu.
4. When Program SWC appears on the display, press
the knob once to select it.
5. Turn the knob to scroll through the available
functions.
6. Once the function desired is highlighted, press and
hold the multi
-function button next to the control
you wish to program (1, 2, 3 or 4). The buttons are
located at the right of the display.
When a control is successfully programmed, the
function you selected will appear next to the number
of the control at the right of the display.
7. Press the multi
-function button next to the Back
prompt to exit each menu. If you desire to program
another control, repeat the procedure.
Each function can only be used once. When you
program a control with a function, that function is
removed from the list of functions available. It will
return to the list if you remove it from the SWC it is
programmed to by programming another function to
that control.

2-47
Turn Signal On Chime
If the turn signal is left on for approximately 1 mile
(1.61 km), a warning chime will sound and the
Turn Signal On message will appear on the Driver
Information Center (DIC) display. See ªTurn Signal
On Messageº later in this section for more information.
Headlamps
The exterior lamp control is located at the end of the
turn signal/multifunction lever.
: Turn the control with this symbol on it to operate
the exterior lamps.
The exterior lamp control has three positions:
: Turning the control to this position turns off all
lamps except the Daytime Running Lamps (DRL).
: Turning the control to this position turns on the
parking lamps together with the following:

Sidemarker Lamps

Taillamps

License Plate Lamps

Instrument Panel Lights
: Turning the control to this position turns on the
headlamps, together with the previously listed lamps
and lights.
AUTO (Automatic): Turning the control to this
position puts the headlamps in automatic mode. AUTO
mode will turn the exterior lamps on and off depending
upon how much light is available outside of the vehicle.
Wiper
-Activated Headlamps
This feature activates the headlamps and parking lamps
after the windshield wipers have been in use for
approximately six seconds. For this feature to work, the
exterior lamp control must be in AUTO.
When the exterior lamp control is off or in the parking
lamp position and the windshield wiper control is in any
position except off, the Headlamps Suggested message
will appear on the DIC display. See ªHeadlamps
Suggested Messageº later in this section for more
information.
When the ignition is turned to OFF, the wiper
-activated
headlamps will immediately turn off. They will also turn
off if the windshield wiper control is turned off.

2-52
Windshield Washer
CAUTION:
In freezing weather, don't use your washer until
the windshield is warmed. Otherwise the washer
fluid can form ice on the windshield, blocking
your vision.
The windshield washer button is located at the end of
the windshield wiper lever.
(Washer Fluid): Press the button with this
symbol located at the end of the windshield washer lever
to wash the windshield. Washer fluid will squirt onto the
windshield and the wipers will run for a few cycles to
clear the windshield. For more wash cycles, press and
hold the button.
If your vehicle is low on washer fluid, the Check
Washer Fluid message will appear on the Driver
Information Center (DIC) display. See ªDriver
Information Center (DIC) Messagesº listed later in this
section for more information.
If the headlamps are on when you wash the windshield,
the headlamp washers (if equipped) will turn on. Both
the windshield and the headlamps will be washed. See
ªHeadlamp Washersº listed previously in this section for
more information.

2-54
Setting Cruise Control
CAUTION:
If you leave your cruise control switch on when
you're not using cruise, you might hit a button
and go into cruise when you don't want to. You
could be startled and even lose control. Keep the
cruise control switch off until you want to use
cruise control.
1. Press the cruise control on/off button to turn cruise
control on. An indicator light will come on to show
that the cruise control is on.
2. Accelerate to the speed you want.
3. Press either the plus or minus button and release it.
This will set the cruise control.
4. Remove your foot from the accelerator pedal.
This light on the instrument
panel cluster will come on
when cruise control is on.
It will go out when cruise
control is turned off.
Resuming a Set Speed
Suppose you set your cruise control at a desired speed
and then you apply the brake. This shuts off the cruise
control. But you don't need to reset it.
Once the vehicle is traveling approximately 25 mph
(40 km/h) or more, you can press the resume/accelerate
button to return to your desired preset speed. The cruise
control light will be displayed again.
The vehicle will return to and stay at your preset speed.
If you press and hold the resume/accelerate button, the
vehicle speed will increase until you release the button
or apply the brake. Unless you want to go faster, do not
press and hold the resume/accelerate button.

2-57
Daytime Running Lamps
Daytime Running Lamps (DRL) can make it easier for
others to see the front of your vehicle during the day.
DRL can be helpful in many different driving
conditions, but they can be especially helpful in the
short periods after dawn and before sunset. Fully
functional daytime running lamps are required on all
vehicles first sold in Canada.
The DRL system will make the turn signal lamps come
on when the following conditions are met:

It is still daylight and the ignition is in ON
or START,

the exterior lamp control is in OFF or AUTO with
the headlamps off, and

an automatic transmission is not in PARK (P) or the
parking brake is not set on a manual transmission.
When DRL are on, only your turn signal lamps will be on.
No other exterior lamps will be on when the DRL are
being used. Your instrument panel won't be lit up either.
When the exterior lamp control is in AUTO and it's dark
enough outside, the DRL will turn off and the low
-beam
headlamps will turn on. When it's bright enough
outside, the low
-beam headlamps will go off, and the
DRL will turn back on.If it's dark enough outside and the exterior lamp control
is in OFF, a Headlamps Suggested message will appear
on the Driver's Information Center (DIC) display. This
message informs the driver that turning on the exterior
lamps is recommended even though the DRL are still
illuminated. Turning the exterior lamp control to AUTO
or to the low
-beam headlamp position will turn off the
DRL and cancel the Headlamps Suggested message.
If the parking lamps or the fog lamps were turned on
instead, the DRL will still turn off and the Headlamps
Suggested message will be displayed. You can turn it off
by pressing the OK button if you have the Navigation
audio system or the CLR button if you have the base
audio system.
To operate your vehicle with the DRL off, turn the
exterior lamp control to OFF. Then turn on the fog
lamps or parking lamps, and the DRL will turn off.
The Headlamps Suggested message will appear on the
DIC display. This will work regardless of gear position
and whether or not the parking brake is set.
As with any vehicle, you should turn on the regular
headlamp system when you need it.

2-59
Interior Lamps
Instrument Panel Brightness Lever
This feature controls the brightness of the instrument
panel lights.
The lever for this feature
is located on the
overhead console.
Slide the lever toward the symbol to brighten the lights
or away from it to dim them.
If you slide the lever all the way toward the symbol past
the resistance point, the interior lamps will come on. To
turn them off, slide the lever back toward the minimum
brightness setting.
Illuminated Entry
The illuminated entry system turns on the reading and
dome lamps and the backlighting to the exterior lamp
control when a door is opened or if you press the remote
keyless entry transmitter unlock button. If activated by
the transmitter, the lighting will remain active for about
25 seconds. The illuminated entry system uses the light
sensor, it must be dark outside in order for the lamps to
turn on. The lamps turn off approximately 25 seconds
after the last door is closed. They will dim to off if the
ignition key is placed in ON, or immediately deactivate
if the power locks are activated.
Parade Dimming
This feature prohibits dimming of the instrument panel
displays and backlighting during daylight hours when
the key is in the ignition and the headlamps are on.
This feature operates with the light sensor and is fully
automatic. When the light sensor reads darkness outside
and the parking lamps are active, the instrument panel
displays can be adjusted by sliding the instrument panel
brightness lever toward the symbol to brighten or away
from the symbol to dim the lighting.

2-61
Electrochromic Day/Night Rearview
Mirror with Compass and OnStar
System
(If Equipped)
Your vehicle may have an electrochromic inside
rearview mirror with a compass. The mirror also
contains OnStar controls. For more information about
OnStar, see ªOnStarº in the Index.
The mirror has an eight
-point compass display in the
upper right corner of the mirror face. When on, the
compass automatically calibrates as the vehicle is
driven.
(On/Off): This is the on/off button, located on the
lower left side of the mirror for the electrochromic
functions of the rearview mirror.
Mirror Operation
The electrochromic feature on the mirror functions
exactly the same as the base electrochromic mirror.
See ªElectrochromic Day/Night Rearview Mirror with
OnStar

Systemº listed previously in this section for
more information.Compass Operation
Press the on/off button once to turn the compass on
or off.
When the ignition and the compass feature are on,
the compass will show two character boxes for
approximately two seconds. After two seconds, the
mirror will display the current compass heading.
Compass Calibration
If after two seconds the display does not show a
compass heading (N for North for example), there may
be a strong magnetic field interfering with the compass.
Such interference may be caused by a magnetic antenna
mount, note pad holder or similar object. If the letter C
should ever appear in the compass window, the compass
may need calibration.
The mirror can be calibrated by driving the vehicle in
circles at 5 mph (8 km/h) or less until the display reads
a direction.
The compass can be placed in calibration mode by
pressing and holding the on/off button until a C is
shown in the compass display.

2-62
Compass Variance
Compass variance is the difference between earth's
magnetic north and true geographic north. If the mirror
is not adjusted for compass variance, your compass
could give false readings.
The mirror is set in zone eight upon leaving the factory.
It will be necessary to adjust the compass to compensate
for compass variance if you live outside zone eight.
Under certain circumstances, such as a long distance,
cross
-country trip, it will be necessary to adjust the
compass variance.
To adjust for compass variance, do the following:
1. Find your current location and variance zone number
on the zone map that follows.
2. Press and hold the on/off button until a zone number
appears on the display.
3. Once the zone number appears on the display, press
the on/off button quickly until you reach the correct
zone number. Stop pressing the button and the mirror
will return to normal operation. If C appears in the
compass window, the compass may need calibration.
See ªCompass Calibrationº listed previously.